Panasonic Projector PT-DZ10KU User Manual

							Chapter 4 Settings — [3D SETTINGS] menu
ENGLISH - 91
[3D SETTINGS] menu
(Only for PT-DZ13KU, PT- DS12KU, PT- DW11KU)
On the menu screen, select [3D SETTINGS] from the main menu, and select \
an item from the 
sub-menu.
Refer to “Navigating through the menu” ( x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[3D SYSTEM SETTING]
Set a picture display method for use during 3D signal input as necessary\
 for the 3D system in use.
1) Press  as to select [3D SYSTEM SETTING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[SINGLE] During 3D signal input, sequential frames of images for the right eye and images for the left eye are 
alternately displayed.
[DUAL (LEFT)] Only images for the left eye are displayed during 3D signal input.
[DUAL (RIGHT)] Only images for the right eye are displayed during 3D signal input.
Note
 fWhen 2D images are input, 2D images are displayed regardless of [3D SYST\
EM SETTING] settings.
[3D SYNC SETTING]
Set the way in which the  terminal and the  terminal will be used.
Attention
 fBefore connecting external devices to the  terminal an\
d the  terminal using cables, complete the 
[3D SYNC MODE] setting and confirm that the external devices to be connected are turned of f.
 fChanging [3D SYNC MODE] while the cables are connected may result in malfunctions of the projector or the connected external devices.
1) Press  as to select [3D SYNC SETTING].
2)  
Press the  button.
 f The precaution message related to [3D SYNC SETTING] is displayed.
3) Press the  button.
 fThe  [3D SYNC SETTING] screen is displayed.
4) Press  as to select [3D SYNC MODE].
5)  
Press 
 qw to switch the item.
[3D SYNC MODE] Items set in [3D SYNC1] Items set in [3D SYNC2]
[OFF] Not used. Not used.
[1] 3D trigger output Stereo synch output
[2] 3D trigger output 3D trigger output
[3] Stereo synch input Through 3D SYNC1
[4] Stereo synch input Stereo synch output
[5] Stereo synch input 3D trigger output
[6] Frame synch input Through 3D SYNC1
[7] Frame synch input Stereo synch output
[8] Frame synch input 3D trigger output
[9] 3D trigger output Frame synch output   
						

							Chapter 4 Settings — [3D SETTINGS] menu
92 - ENGLISH
[3D SYNC MODE]Items set in [3D SYNC1] Items set in [3D SYNC2]
[10] Stereo synch output Frame synch output
[11] 3D IR TRANSMITTER (+) output 3D IR TRANSMITTER (
-) output
6) When [1], [4], [7], or [10] is selected, press as  to select [STEREO SYNC OUTPUT DELAY], and press 
qw to set the amount of delay output.
[0us] - [25 000 us] Allows you to set in increments of 10   us.
 fT

o synchronize multiple projectors to display 3D images, use a frame synch input and output.
Select [9] or [10] for the first projector.
Select [6], [7], or [8] for the second and subsequent projectors.
 f Stereo synchronization is a signal having a 

  50   % duty cycle where High is for the left eye and Low is for the right eye.
 f“H” is output to the 3D image display and “L” is output to the 2D image display from the terminal for which 3D trigger output is selected.
Note
 f[11] or [3D SYNC MODE] is the setting when the 3D IR transmitter TY-3DTRW of Panasonic is used with the projector. Consult your dealer 
regarding the connection method.
[3D SIMUL INPUT SETTING]
Set this item to input and use 3D video signals of the simultaneous syst\
em.
1) Press  as to select [3D SIMUL INPUT SETTING].
2)  
Press the  button.
 f The  [3D SIMUL INPUT SETTING]  screen is displayed.
3) Press as to select [LEFT:RGB1 RIGHT:RGB2], [LEFT:HDMI RIGHT:DVI-D], or [LEFT:SDI1 RIGHT:SDI2] 
(only for PT
-
 DZ13KU, PT
-
 DS12KU).
4)
 
Press 
 qw to switch the setting.
[OFF] Cannot use 3D simultaneous.
[AUTO] Displays 3D images of the simultaneous system.
Note
 fWhen set to [AUT O], 3D images are displayed when the same 3D compatible signals are entered to each input. However , the P IN P status 
during P IN P is maintained.
 f This may not function properly for some connected external devices. fCertain signals may not function properly

.
[3D INPUT FORMAT]
Set the 3D format for the image signals being input.
Set a 3D format that matches the input signal.
1) Press as to select [3D INPUT FORMAT].
2)  
Press the  button.
 f The  [3D INPUT FORMAT] screen is displayed.
3) Press  as to select a 3D format.
[AUTO]*1Automatically detects 3D format of input image signals and displays imag\
es.
[NATIVE] Forcibly displays 2D images regardless of input image signals.
[SIMULTANEOUS]
*2Forcibly displays 3D images in simultaneous system regardless of input v\
ideo signals.
[SIDE BY SIDE] Forcibly displays 3D images in side by side format regardless of input i\
mage signals.
[TOP AND BOTTOM] Forcibly displays 3D images in top and bottom format regardless of input\
 image signals.
[LINE BY LINE]
*3Forcibly displays 3D images in line by line system regardless of input v\
ideo signals.
[FRAME SEQUENTIAL]
*4Forcibly displays 3D images in frame sequential format regardless of input image signals.
*1 During DVI - D or HDMI input only
*2  
During 3G
 - SDI level B input only
*3
 
Only while signals other than interlaced signals are input
*4

 
Only while progressive signals with the vertical scanning frequency of 100
   Hz or 120   Hz are input to the // terminals
4) Press the  button.   
						

							Chapter 4 Settings — [3D SETTINGS] menu
ENGLISH - 93
Note
 fWhen set to [AUT O], [SIMULTANEOUS], [SIDE BY SIDE], [TOP AND BOTTOM], [LINE BY LINE], or [FRAME SEQUENTIAL], 3D images 
are not displayed in [3D SIMUL INPUT SETTING]. In [AUTO], however, this only occurs when 3D format can be recognized.
 f This may not function properly for some connected external devices.
[LEFT/RIGHT SWAP]
Display images by inverting the timing of horizontal image switching. Change the settings when there is something wrong with the 3D image 
being viewed.
1) Press  as to select [LEFT/RIGHT SWAP].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Do not change the [NORMAL] setting if the 3D images are displayed correc\
tly.
[SWAPPED] Select this when left and right 3D images are swapped to be displayed.
Note
 fThis is disabled when [3D SYSTEM SETTING] is set to other than [SINGLE].
[3D COLOR MATCHING]
Switches the color matching correction data applied to the displayed image.
1) Press  as to select [3D COLOR MATCHING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[SHARED 2D/3D] 2D signals and 3D signals use the same correction data.
[SEPARATE 2D/3D] 2D signals and 3D signals use different correction data.
Note
 fSwitch the setting of [COLOR MA TCHING] (x   page   96) while inputting the signal to be adjusted.
[3D PICTURE BALANCE]
Correct a shift when the brightness or color differ in the right eye and left eye images.
1) Press as to select [3D PICTURE BALANCE].
2)  
Press the  button.
 f The  [3D PICTURE BALANCE]  screen is displayed.
3) Press as to select an item, and press qw to adjust the setting.
 fCorrect the setting value parts of the right eye image based on the left\
 eye image.
 fFor [3D W

AVEFORM MONITOR], the left eye and right eye images are divided and displayed in a waveform on the left and right.
[CONTRAST] Adjusts the contrast of the colors.
[WHITE BALANCE HIGH  RED] Adjusts the high red white balance.
[WHITE BALANCE HIGH  GREEN] Adjusts the high green white balance.
[WHITE BALANCE HIGH  BLUE] Adjusts the high blue white balance.
[BRIGHTNESS] Adjusts the dark (black) part of the projected image.
[WHITE BALANCE LOW RED] Adjusts the low red white balance.
[WHITE BALANCE LOW  GREEN] Adjusts the low green white balance.
[WHITE BALANCE LOW  BLUE] Adjusts the low blue white balance.
[COLOR] Adjusts the color saturation of the projected image.
[TINT] Adjusts the skin tone in the projected image.
[CLOCK PHASE] Adjusts when the screen flickers or outline blurs.   
						

							Chapter 4 Settings — [3D SETTINGS] menu
94 - ENGLISH
[3D WAVEFORM MONITOR][OFF]
Hides the 3D waveform monitor.
[ON] Displays the 3D waveform monitor.
Note
 fThe [CLOCK PHASE] setting is enabled at simultaneous input of RGB1 and R\
GB2 to adjust the right eye image. fThis is disabled when [3D SYSTEM SETTING] is set to other than [SINGLE]. fThis is disabled when [3D 

TEST PATTERN] is displayed.
 fThis is disabled when [3D 

TEST MODE] is set to other than [NORMAL] or [SIDE BY SIDE].
 fThe 3D waveform monitor is displayed only when the  [3D PICTURE BALANCE] screen is displayed. fThe normal waveform monitor cannot be displayed in 3D images.
[DARK TIME SETTING]
Set the black display period to be displayed between the right eye image and the left eye image as necessary for the 3D system used.
1) Press  as to select [DARK TIME SETTING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[0.5 ms]
Set so that the 3D setting is displayed correctly.
[1.0 ms]
[1.5 ms]
[2.0 ms]
[2.5 ms]
[2.7 ms]
Note
 f
This is disabled when [3D SYSTEM SETTING] is set to other than [SINGLE]. fWhen the setting does not correspond to the 3D system in use, phenomenon\
 such as increased crosstalk and darkening of displayed 
images may occur
.
[3D FRAME DELAY]
Adjust the timing of the left-right switch of an image.
1) Press as to select [3D FRAME DELAY].
2)  
Press 
 qw to switch the item.
[0us] - [25 000 us] Allows you to set in increments of 10   us.
 fThe adjustment range depends on the input signal.
[3D TEST MODE]
Set the image display system for use with 3D system adjustments.
1) Press  as to select [3D TEST MODE].
2)  
Press 
 qw to switch the item.
[NORMAL] Standard setting.
[SIDE BY SIDE] The left eye image is displayed on the left, next to the right eye image\
 displayed on the right.
[LEFT/LEFT] Both the left eye image and right eye image display the left eye input s\
ignal.
[RIGHT/RIGHT] Both the left eye image and right eye image display the right eye input \
signal.
[LEFT/BLACK] The left eye input signal is displayed in the left eye image and a compl\
etely black image is displayed 
in the right eye image.
[BLACK/RIGHT] A completely black image is displayed in the left eye image and the right\
 input signal is displayed in 
the right eye image.
Note
 f
The [3D TEST MODE] settings return to [NORMAL] when the projector is switched off. fThis is disabled when [3D SYSTEM SETTING] is set to other than [SINGLE]. fThis is disabled when [3D 

TEST PATTERN] is displayed.   
						

							Chapter 4 Settings — [3D SETTINGS] menu
ENGLISH - 95
[3D TEST PATTERN]
The 3D test pattern can be used to check operation and make adjustments even without a 3D signal.
1) Press as to select [3D TEST PATTERN].
2)  
Press 
 qw to switch the item.
Menu screen + Entry screen
Select a test pattern so that it is easy to check operations and make ad\
justments.
Menu screen + Left: white/
Right: black
Menu screen + Left: black/ Right: white
Note
 fThe 3D test pattern cannot be displayed when the following inputs are selected. gVIDEO input gRGB1 input (only when [RGB IN] is set to [Y/C]) fThis is disabled when [3D SYSTEM SETTING] is set to other than [SINGLE].
[SAFETY PRECAUTIONS MESSAGE]
Set to show or hide the safety precautions message related to 3D viewing when the projector is switched on.
1) Press  as to select [SAFETY PRECAUTIONS MESSAGE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[ON] Shows the safety precautions message related to 3D viewing when the projector is switched on.
[OFF] Hides the safety precautions message related to 3D viewing when the projector is switched on.
Note
 fSet to [OFF] to hide the safety precautions message related to 3D viewing when the projector is switched on. fA
 confirmation screen is displayed when switched from [ON] to [OFF]. Press qw to select [OK], and press the  button to change 
the setting to [OFF].
Attention
 f When 3D images are viewed by unspecified number of people for commercial use, display the safety precautions message related to 3D 
viewing to notify viewers.
[3D SAFETY PRECAUTIONS]
Show the safety precautions message related to 3D viewing.
1) Press  as to select [3D SAFETY PRECAUTIONS].
2)  
Press the  button.
 f The  [3D SAFETY PRECAUTIONS] screen is displayed.
 fPress 

qw to switch the page.
1/2
MENU
2/2
MENU
3D SAFETY PRECAUTIONS
If you view 3D images, please note below.
In addition, when 3D images will be viewed
by unspecified number of people
or used for commercial applications,
someone in authority should convey
the following precautions.
To enjoy 3D images safely and comfortably,
please refer to the Operating Instructions
for in-depth description.
CHANGE
EXIT
3D SAFETY PRECAUTIONSPlease refrain from viewing 3D images
if you do not feel well or are experiencing
visual fatigue.
Please use the contents which has been
properly made for 3D.
View from at least the recommended distance.
(3 times the effective height of the screen)
Refer to the Operating Instructions
if this message is no longer needed.
CHANGE
EXIT   
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
96 - ENGLISH
[DISPLAY OPTION] menu
On the menu screen, select [DISPLAY OPTION] from the main menu, and select an item from 
the sub-menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[COLOR MATCHING]
Correct the color difference between projectors when using multiple projectors simultaneously.
Adjusting the color matching as desired
1) Press  as to select [COLOR MATCHING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Color matching adjustment is not carried out.
[3COLORS] Adjusts the three colors [RED], [GREEN], or [BLUE].
[7COLORS] Adjusts the seven colors [RED], [GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW], or [WHITE].
[709MODE] Refer to “Adjusting the color matching using a colorimeter” ( x
  page   97) for details about this mode.
[MEASURED]
3) Select [3COLORS] or [7COLORS], and press the  button.
 f The  [3COLORS] or [7COLORS] screen is displayed.
4) Press  as to select [RED], [GREEN], or [BLUE] ([RED], [GREEN], [BLUE], [CYAN], [MAGENTA], 
[YELLOW], or [WHITE] for [7COLORS]).
5)
 
Press the  button.
 f The  [3COLORS:RED], [3COLORS:GREEN], or [3COLORS:BLUE] screen is displayed.
For [7COLORS], the  [7COLORS:RED], [7COLORS:GREEN], [7COLORS:BLUE], [7COLORS:CYAN], [7COLORS:MAGENTA], 
[7COLORS:YELLOW] , or [7COLORS:WHITE] screen is displayed.
 fSet [AUT

O TESTPATTERN] to [ON] to display a test pattern of selected colors.
6) Press  as to select [RED], [GREEN], or [BLUE].
7)  
Press 
 qw to adjust.
 fThe adjustment value changes between 0 and 2   048.
Note
 fOperation when correcting the adjustment color
When the correction color same as the adjustment color is changed: 
The luminance of the adjustment color changes.
When correction color red is changed: Red is added to or subtracted from\
 the adjustment color.
When correction color green is changed: Green is added to or subtracted \
from the adjustment color.
When correction color blue is changed: Blue is added to or subtracted fr\
om the adjustment color.
 f This adjustment should be carried out by a person who is familiar with the projector or by a service person because a high level of skill is 
required to make a successful adjustment.
 fPressing the  button will restore the factory default settings for all items.
 fWhen [COLOR MA

TCHING] is set to other than [OFF], [COLOR TEMPERATURE] is fixed to [USER1].
 fSet [3D COLOR MA

TCHING] (x   page   93) to set whether 2D and 3D signals are set separately or whether common data is used. (Only 
for PT
-

DZ13KU, PT
-
 DS12KU, PT
-
 DW11KU)
 fWhen 2D and 3D settings are set separately

, [NATIVE] or [3D] is displayed in the upper right of the menu. (Only for PT
-
 DZ13KU, 
PT
-

DS12KU, PT
-
 DW11KU)   
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 97
Adjusting the color matching using a colorimeter
Use a colorimeter that can measure chromaticity coordinates and luminanc\
e to change the colors [RED], [GREEN], [BLUE], [CYAN], 
[MAGENTA], [YELLOW], or [WHITE] to desired colors.
1) Press as to select [COLOR MATCHING].
2)  
Press 
 qw to select [709MODE] or [MEASURED].
3)
 
Press the  button.
 f The  [709MODE] or [MEASURED MODE] screen is displayed.
4) Press  as to select [MEASURED DATA].
5)  
Press the  button.
 f The  [MEASURED DATA] screen is displayed.
6) Measure the current luminance (Y) and the chromaticity coordinates (x\
, y) using the colorimeter .
7)  
Press 
 as to select a color, and press qw to adjust the setting.
 fSet [AUTO TESTPATTERN] to [ON] to display a test pattern of selected colors.
8) Once all the input is completed, press the  button.
 fThe  [709MODE] or [MEASURED MODE] screen is displayed.
 fWhen [MEASURED] is selected in Step  2)

, proceed to Step 9) and enter the coordinates of desired colors.
9) Press as to select [TARGET DATA].
10)  
Press the  button.
 fThe  [TARGET DATA] screen is displayed.
11) Press  as to select a color and press qw to input coordinates for desired colors.
 fSet [AUTO TESTPATTERN] to [ON] to display a test pattern of selected colors.
12) Once all the input is completed, press the  button.
Note
 f When [709MODE] is selected in [COLOR MA TCHING], the ITU - R BT.709 standard three primary colors are set as target data. fColors are not displayed properly when target data is a color outside the region of this projector . fThe [709MODE] may dif

fer slightly from the ITU - R BT.709 standard colors.
 fSet the [AUT

O TESTPATTERN] to [ON] to automatically display a test pattern for use in adjust\
ing the selected adjustment colors.
 fBefore using a colorimeter or similar instrument to measure measurement \
data, set [PICTURE MODE] to [DYNAMIC]. fA

 difference in the color coordinates of target data and measurement values o\
btained from an instrument may occur for certain instruments 
and measurement environments used.
 f [AUT

O TESTPATTERN] settings change together with the [AUTO TESTPATTERN] of [EDGE BLENDING].
[LARGE SCREEN CORRECTION]
Corrects the phenomenon in which colors that appear lighter when viewed on a large screen viewed from a close distance compared to when 
viewed on an average screen size so that colors appear the same.
1) Press  as to select [LARGE SCREEN CORRECTION].
2)  
Press 
 qw to switch the item.
[OFF] Performs no correction.
[1] Performs weak correction.
[2] Performs strong correction.
[SCREEN SETTING]
(Only for PT-DZ13KU, PT- DS12KU, PT- DZ10KU)
Set the screen size.
When changing the aspect of a projected image, correct to the optimum im\
age position for the set screen. Set as necessary for the screen in 
use.
1) Press  as to select [SCREEN SETTING].
2)  
Press the  button.
 f The  [SCREEN SETTING] screen is displayed.   
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
98 - ENGLISH
3) Press qw to switch the [SCREEN FORMAT] item.
 fThe items will switch each time you press the button.
Model No. [SCREEN FORMAT] Range when [SCREEN POSITION] is selected
PT
-

DZ13KU, PT
-
 DZ10KU [16:10]
Cannot be adjusted.
[4:3] Adjusts the horizontal position between 
-160 and 160.
[16:9] Adjusts the vertical position between 
-60 and 60.
PT
-

DS12KU [4:3]
Cannot be adjusted.
[16:9] Adjusts the vertical position between 
-132 and 131.
4) Press as to select [SCREEN POSITION].
 fIf [SCREEN FORMA T] is set to [16:10] in PT- DZ13KU and PT- DZ10KU, or [SCREEN FORMAT] is set to [4:3] in PT- DS12KU, then 
selection and adjustment of [SCREEN POSITION] are not available.
5) Press  qw to adjust [SCREEN POSITION].
[AUTO SIGNAL]
Set whether to execute automatic setup of signals automatically.
The screen display position or signal level can be adjusted automatically without pressing the  button on the remote control 
on each occasion if you input unregistered signals frequently at meetings, etc.
1) Press  as to select [AUTO SIGNAL].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Sets the auto signal function to off.
[ON] Executes automatic setup automatically when images are changed to unregistered signals during 
projection.
[AUTO SETUP]
Set this when adjusting a special signal or horizontally long (such as 16:9) signal.
Setting with [MODE]
1) Press 
as to select [AUTO SETUP].
2)  
Press the  button.
 f The  [AUTO SETUP] screen is displayed.
3) Press  as to select [MODE].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[WIDE] Select when an image aspect is a wide-screen signal, which does not meet the [DEF AULT] settings.
[USER] Select when receiving a signal with a special horizontal resolution (number of display dots).
 fWhen [DEF

AULT] or [WIDE] is selected, proceed to Step  7).
 fWhen [USER] is selected, proceed to Step  5)

.
5) Press as to select [DISPLAY DOTS], and press qw to adjust [DISPLAY DOTS] to the horizontal 
resolution of the signal source.
6)
 
Press 
 as to select [MODE].
7)
 
Press the  button.
 f Automatic adjustment is executed. [PROGRESS] is displayed while automatically adjusting. When complete, the system returns to the 
[AUT
O SETUP] screen.
Adjusting position automatically
1) Press  as to select [AUTO SETUP].   
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 99
2) Press the  button.
 fThe  [AUTO SETUP] screen is displayed.
3) Press  as to select [POSITION ADJUST].
4)  
Press 
 qw to switch the item.
[OFF] Does not perform automatic adjustment.
[ON] Adjust the screen position and size when automatic setup is executed.
Adjusting signal level automatically
1) Press as to select [AUTO SETUP].
2)  
Press the  button.
 f The  [AUTO SETUP] screen is displayed.
3) Press  as to select [SIGNAL LEVEL ADJUST].
4)  
Press 
 qw to switch the item.
[OFF] Does not perform automatic adjustment.
[ON] Adjusts black level (on-screen menu [BRIGHTNESS]) and white level (on-screen menu 
[CONTRAST]) when automatic setup is executed.
Note
 f
[SIGNAL LEVEL ADJUST] may not function properly unless a still image containing clear blacks and whites is input.
[RGB IN]
Set to match the signal to input to the  terminal.
Setting [RGB1 INPUT SETTING]
1) Press  as to select [RGB IN].
2)  
Press the  button.
 f The  [RGB IN] screen is displayed.
3) Press  as to select [RGB1 INPUT SETTING].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[RGB/YPBPR] Select when inputting an RGB signal or YCBCR/YPBPR signals to the  terminal.
[Y/C] Select when inputting a luminance signal and color signal to the  terminal.
Switching the slice level of an input sync signal
1) Press as to select [RGB IN].
2)  
Press the  button.
 f The  [RGB IN] screen is displayed.
3) Press  as to select [RGB1 SYNC SLICE LEVEL] or [RGB2 SYNC SLICE LEVEL].
4)  
Press 
 qw to switch the item.
[LOW] Sets the slice level to [LOW].
[HIGH] Sets the slice level to [HIGH].   
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
100 - ENGLISH
[DVI-D IN]
Switch the setting when the external device is connected to the  terminal of the projector and the image is not projected correctly.
1) Press as to select [DVI-D IN].
2)  
Press the  button.
 f The  [DVI-D IN] screen is displayed.
3) Press  as to select [EDID].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[EDID3] Recognizes movie-based video signals and still image signals automatically .
[EDID1] Select mainly when an external device that outputs movie-based video signals (such as a blu-ray disc 
player) is connected to the  terminal.
[EDID2:PC] Select mainly when an external device that outputs still image signals (such as a computer) is 
connected to the  terminal.
5) Press 
as to select [SIGNAL LEVEL].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.
[0 - 255:PC] Select when an external device (such as a computer) is connected via the DVI
- D terminal output.
[16
- 235] Select when an external device (such as a blu-ray disc player) is connected via the HDMI terminal 
output using a conversion cable, etc.
Note
 f
The optimal setting varies depending on the output setting of the connec\
ted external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
 fThe data for Plug and play will change when the setting is changed. Refer to “List of compatible signals” ( x

  page   175) for a resolution that 
supports plug and play.
[HDMI IN]
Switch the setting when the external device is connected to the  terminal of the projector and the image is not projected correctly .
1) Press as to select [HDMI IN].
2)  
Press the  button.
 f The  [HDMI IN] screen is displayed.
3) Press  qw to switch the [SIGNAL LEVEL] item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.
[64 - 940] Select when the HDMI terminal of an external device (such as a blu-ray disc player) is connected to 
the  terminal.
[0
- 1023] Select when the DVI
- D terminal output of an external device (such as a computer) is connected to the 
 terminal via a conversion cable or similar cable.
Select also when the HDMI terminal output of a computer or other device is connected to the  terminal.
Note
 f The optimal setting varies depending on the output setting of the connec\
ted external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
 fThe HDMI signal level is displayed for every 30

  bits of input.
[SDI IN]
(Only for PT-DZ13KU, PT- DS12KU, PT- DZ10KU)
Set to match the signal to input to the / terminals (PT
-
 DZ13KU, PT
-
 DS12KU) or  terminal (PT
-
 DZ10KU).