Panasonic Network Disk Recorder Wjnd300a Setup Instructions

11
Screenshot 3
The Network and Internet Connections window will be
displayed.
Step 3
Click Network Connections.
Screenshot 4
The Network Connections window will be displayed.
Step 4
Double click Local Area Connection.
Screenshot 5
The Local Area Connection Status window will be dis-
played.
Step 5
Click Properties. 

12
Screenshot 6
The Local Area Connection Properties window will be
displayed.
Step 6
Click Internet Protocol (TCP/IP), and then click
Properties.
Screenshot 7
The Properties window of Internet Protocol (TCP/IP)
will be displayed.
Step 7
Click Use the following IP address and enter the IP
address and the subnet mask as follows;
•IP address: 192.168.1.100
•Subnet mask: 255.255.255.0
Depending on the network configuration, it may be nec-
essary to set the Default gateway. Refer to a system
administrator...

13
Equipped Security Functions
qAccess restrictions by the host authentication and the user authentication
It is possible to restrict users from accessing this unit by setting the host authentication and/or the user authenti-
cation to on. (page 75)
wAccess restrictions by changing the HTTP port
It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP port number. (page 65)
For Enhanced Security
Divide the subnet using a router to enhance the network security by double...

14
Display the Operation Window
To display the operation window to operate the unit from the web browser installed on the PC, proceed as follows.
Screenshot 1
Start just after the PC is started up.
Step 1
After the browser starts, enter the IP address set to this
unit in the address box, and press the enter key.
Important:
•Refer to a system administrator for the set IP
address of this unit.
•It is impossible to access this unit from a PC without
a registered IP address when ON is selected for
Host...

15
Screenshot 3
The top page will be displayed.
Step 3
Click the buttons or the tabs for operations.
Important:
If a message is displayed on the information bar,
see page 101.
Note:
When the top page is displayed for the first time, the
install wizard of the ActiveX control required to dis-
play images from the camera will be displayed.
Follow the instructions of the wizard.
•When the install wizard is displayed again even
after completing the installation of the ActiveX,
restart the PC.
Important:
When...

16
About the Operation Window
[Control] tab
[Cam Select] tab
[Setup] tabStatus display areaCurrent time display area
Playback image
display area
Time and date of the
selected camera
Playback point
operation area
[HDD] tab
[CAM] tab
Camera title
Top Page
[Control] tab (page 17)
This tab is for performing operations such as searching
for recorded pictures on an HDD and copying recorded
pictures into the copy area of the HDD. From this tab,
you can also perform the functions of the camera pic-
ture switcher...

17
[Control] Tab
[Multiscreen Select] box
Up to 4 camera images can be displayed simultaneous-
ly on a 4-Screen.
Each time the button is clicked, the camera picture is
changed to quad display according to the settings made
in [System] – [Basic Setup] – [Monitor Display] of the
setup menu (Advanced).
[Sequence] box
Camera images to be displayed will be switched by
clicking this button. Camera images will be displayed
sequentially according to the settings performed in
advance.The lamp on the button lights...

18
[Cam Select] Tab
[Multiscreen Select] box
Multiscreen button:
Up to 4 camera images can be displayed simultaneous-
ly on a multi-screen.
Each time the button is clicked, the camera picture is
changed to quad display according to the settings made
in [System] – [Basic Setup] – [Monitor Display] of the
setup menu (Advanced).
[Sequence] box
Sequence button:
Camera images to be displayed will be switched by
clicking this button. Camera images will be displayed
sequentially according to the settings...

19
[Setup] Tab (Quick)
Display Setup
This button is for performing basic settings such as
date, time, and language display. Refer to page 28 for
further information.
Camera Setup
This button is for performing camera network settings
and group settings. Refer to page 30 for further informa-
tion.
Rec & Event Setup
Performs the basic settings for recording operation and
for event action. Refer to page 31 for further informa-
tion.
Network Setup
Settings for a network can be performed. Refer to page
35 for...

20
[Setup] Tab (Advanced)
Important:
When the settings are applied, all users who have
logged in to this unit will be forcibly logged out.
[System] button
The menu for the required system settings to activate
this unit will be displayed. Refer to page 42 for further
information.
[Recording] button
The menu for the recording settings will be displayed.
Perform the basic settings for recording and the settings
for emergency recording. Refer to page 46 for further
information.
[Event] button
Displays the...