Panasonic Network Disk Recorder Wjnd300a Setup Instructions

							11
Screenshot 3
The Network and Internet Connections window will be
displayed.
Step 3
Click Network Connections.
Screenshot 4
The Network Connections window will be displayed.
Step 4
Double click Local Area Connection.
Screenshot 5
The Local Area Connection Status window will be dis-
played.
Step 5
Click Properties. 
						

							12
Screenshot 6
The Local Area Connection Properties window will be
displayed.
Step 6
Click Internet Protocol (TCP/IP), and then click
Properties.
Screenshot 7
The Properties window of Internet Protocol (TCP/IP)
will be displayed.
Step 7
Click Use the following IP address and enter the IP
address and the subnet mask as follows;
•IP address: 192.168.1.100
•Subnet mask: 255.255.255.0
Depending on the network configuration, it may be nec-
essary to set the Default gateway. Refer to a system
administrator for further information.
Step 8
Click the OK button and close the window. 
						

							13
Equipped Security Functions
qAccess restrictions by the host authentication and the user authentication
It is possible to restrict users from accessing this unit by setting the host authentication and/or the user authenti-
cation to on. (page 75)
wAccess restrictions by changing the HTTP port
It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP port number. (page 65)
For Enhanced Security
Divide the subnet using a router to enhance the network security by double authentications of IP addresses using
this unit and a router. When required to connect this unit with a network without enhanced security, connect the unit
after the network security is enhanced, such as by installing a VPN (Virtual Private Network) device, etc.
Important:
The settings of the unit will be different depending on the settings of the LAN or the Internet service provider to
which the unit is to be connected. Refer to an administrator of each network for further information about the
respective network.
[Connection example]
Installing a firewall to use the packet filtering and the protocol filtering functions can better enhance the network
security.
[Connection example]
About the Network Security of this Unit
WAN*
Router Router
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
IP Address: 192.168.1.250
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
IBM PC/AT Compatible IP Address: 192.168.0.1
Subnet Mask: 255.255.255.0
This unit
* Stands for Wide Area Network
10/100BASE-T
21
EXT STORAGESERIAL
PCCAMERAAC   INON
ALARM/CONTROLALARM
SIGNAL GNDPOWEROFF
WAN*
Switching hub Firewall
Router Router
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0 IP Address: 192.168.0.1
Subnet Mask: 255.255.255.0
IP Address: 192.168.1.250
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
IBM PC/AT Compatible* Stands for Wide Area Network
This unit
10/100BASE-T
21
EXT STORAGESERIAL
PCCAMERAAC   INALARM/CONTROLALARM
SIGNAL GNDPOWER
ONOFF 
						

							14
Display the Operation Window
To display the operation window to operate the unit from the web browser installed on the PC, proceed as follows.
Screenshot 1
Start just after the PC is started up.
Step 1
After the browser starts, enter the IP address set to this
unit in the address box, and press the enter key.
Important:
•Refer to a system administrator for the set IP
address of this unit.
•It is impossible to access this unit from a PC without
a registered IP address when ON is selected for
Host Authentication on the Basic Setup of User
Mng. menu.
Refer to a system administrator for further informa-
tion.
•Do not attach 0 before the numbers when entering
IP address.
Example
Correct: 192.168.0.50
Wrong: 192.168.0.050
•If a message is displayed on the information bar,
see page 101.
Screenshot 2
The user authentication window will be displayed.
This window will not be displayed when OFF is select-
ed for User Authentication on the Basic Setup of
User Mng. menu.
Step 2
Enter the user ID and password registered on this unit.
Important:
•Refer to a system administrator for the set user
name and password.
Refer to page 77 for the descriptions of how to regis-
ter users.
•The default administrator name and password are
as follows.
USER ID: ADMIN
Password: 12345
•To enhance the security, change the password for
an administrator before running the unit. It is recom-
mended to change the password for the administra-
tor periodically. Refer to page 76 for descriptions of
how to change the password. 
						

							15
Screenshot 3
The top page will be displayed.
Step 3
Click the buttons or the tabs for operations.
Important:
If a message is displayed on the information bar,
see page 101.
Note:
When the top page is displayed for the first time, the
install wizard of the ActiveX control required to dis-
play images from the camera will be displayed.
Follow the instructions of the wizard.
•When the install wizard is displayed again even
after completing the installation of the ActiveX,
restart the PC.
Important:
When the unit is being operated without changing
the default administrator name and password, the
pop-up window saying that it is recommended to
change the password will be displayed. 
						

							16
About the Operation Window
[Control] tab
[Cam Select] tab
[Setup] tabStatus display areaCurrent time display area
Playback image
display area
Time and date of the
selected camera
Playback point
operation area
[HDD] tab
[CAM] tab
Camera title
Top Page
[Control] tab (page 17)
This tab is for performing operations such as searching
for recorded pictures on an HDD and copying recorded
pictures into the copy area of the HDD. From this tab,
you can also perform the functions of the camera pic-
ture switcher such as changing the display of camera
live pictures to quad or sequence display. Search
results or log information will also be displayed on this
page.
[Cam Select] tab (page 18)
The switcher functions such as switching camera chan-
nels are operable on this page.
[Setup] tab (pages 19 and 20)
Operations for setup of this unit can be performed on
this tab. Using the setup menu (Quick) and the setup
menu (Advanced)
Status display area (Page 21)
Current status such as playback status or recording sta-
tus will be displayed.
Current time display area
Current time will be displayed.Playback image display area
Recorded images and live images will be displayed. The
setup menu will be displayed while setting up.
The camera title is displayed at the top left of the picture
and the time (current camera time for live pictures and
recorded time for recorded pictures) at the top right.
Clicking the camera title during quad display will display
the clicked picture on a single screen.
Playback point operations area (page 23)
It is possible to mark playback points or skip to the lat-
est recorded image.
[HDD] tab (page 23)
Operation for recorded images such as playback or
downloading (saving) recorded images can be per-
formed on this page.
[CAM] tab (page 25)
Perform the camera operations such as zooming, focus-
ing, auto functions, etc. on this panel. 
						

							17
[Control] Tab
[Multiscreen Select] box
Up to 4 camera images can be displayed simultaneous-
ly on a 4-Screen.
Each time the button is clicked, the camera picture is
changed to quad display according to the settings made
in [System] – [Basic Setup] – [Monitor Display] of the
setup menu (Advanced).
[Sequence] box
Camera images to be displayed will be switched by
clicking this button. Camera images will be displayed
sequentially according to the settings performed in
advance.The lamp on the button lights (green) during sequence
operation.
[EL-Zoom] box
Camera images will be displayed in the proportion of the
clicked zoom ratio button.
:1x :2x :4x
[Search] box
[Search] button:The recording event
search will be displayed. Use this button to search
the recorded images. (Refer to the Operating
Instructions (PDF).)
Search results will be displayed in list form in the log
display area. (Refer to the Operating Instructions
(PDF).)
[Disk Select] button:The disk select win-
dow will be displayed. Use this button to select a
disk to be played/searched. (Refer to the Operating
Instructions (PDF).)
[Copy] box
The copy window will be displayed by clicking this but-
ton. This window is used to copy recorded images into
the copy area of the HDD.
[Log] box
[Error Log] button:The error logs of this unit
will be displayed. Logs will be displayed in list form
in the log display area.
[Access Log] button:The time when logged
in/out for this unit, the user ID, and the IP address
will be displayed.
Logs will be displayed in list form in the log display
area.
[Event Log] button:The event logs (event
occurrence times and their details) will be displayed.
Logs will be displayed in list form in the log display
area.
[Network Log] button:The network error logs
will be displayed.
Logs will be displayed in list form in the log display
area.
[Zoom In]:Enlarges the live camera image
and playback picture. 
						

							18
[Cam Select] Tab
[Multiscreen Select] box
Multiscreen button:
Up to 4 camera images can be displayed simultaneous-
ly on a multi-screen.
Each time the button is clicked, the camera picture is
changed to quad display according to the settings made
in [System] – [Basic Setup] – [Monitor Display] of the
setup menu (Advanced).
[Sequence] box
Sequence button:
Camera images to be displayed will be switched by
clicking this button. Camera images will be displayed
sequentially according to the settings performed in
advance.
[EL-Zoom] box
Camera images will be displayed in the proportion of the
clicked zoom ratio button.
:1x :2x :4x
[Cam Select] box
Clicking the camera title will display a list of cameras
connected to the unit.
Images from the selected camera channel will be dis-
played on the image display area by clicking one of
camera names.
Group title
Camera title 
						

							19
[Setup] Tab (Quick)
Display Setup
This button is for performing basic settings such as
date, time, and language display. Refer to page 28 for
further information.
Camera Setup
This button is for performing camera network settings
and group settings. Refer to page 30 for further informa-
tion.
Rec & Event Setup
Performs the basic settings for recording operation and
for event action. Refer to page 31 for further informa-
tion.
Network Setup
Settings for a network can be performed. Refer to page
35 for further information.
[Registration] button
Applies the settings to this unit. Click this button to com-
plete the setting after editing on the setup menu. 
						

							20
[Setup] Tab (Advanced)
Important:
When the settings are applied, all users who have
logged in to this unit will be forcibly logged out.
[System] button
The menu for the required system settings to activate
this unit will be displayed. Refer to page 42 for further
information.
[Recording] button
The menu for the recording settings will be displayed.
Perform the basic settings for recording and the settings
for emergency recording. Refer to page 46 for further
information.
[Event] button
Displays the setting menu for event actions of each
event type (site alarm, terminal alarm and command
alarm). Refer to page 49 for further information.
[Schedule] button
The menu for the settings of the recording schedule
(performs recording/event action by designating the
time and a day of the week) will be displayed. Refer to
page 53 for further information.
[Camera]
This button is for performing camera network settings,
group settings and sequence operation settings. 
Refer to page 60 for further information.
[Comm] button
The menu for basic network settings will be displayed.
Refer to page 64 for further information.
[User Mng.] button
Displays a menu for registering user information. Refer
to page 75 for further information.
[Maintenance] button
The menu for the settings of the hard disk will be dis-
played. Refer to page 82 for further information.
[Registration] button
Applies the settings to this unit. Click this button to com-
plete the setting after editing on the setup menu.Main menu
Submenu