Panasonic Network Disk Recorder Wjnd300a Setup Instructions

							21
Status Display Area
wer
q
qThe status of live/playback image will be
displayed.
(LIVE]:
Indicates that a live image is being displayed.
(Playback):
Indicates that a playback image is being dis-
played.
(Reverse playback):
Indicates that a reverse playback image is being
displayed.
(Fast playback):
Indicates that a fast playback image is being dis-
played.
(Fast reverse playback):
Indicates that a fast reverse playback image is
being displayed.
(Pause):
Indicates that a paused image is being dis-
played.
:
Indicates that the A-B repeat playback mode is
active.
:
Indicates that the A-B repeat reverse playback
mode is active.
:
Indicates that the A-B repeat fast playback mode
is active.
:
Indicates that the A-B repeat fast reverse play-
back mode is active.
:
Indicates that the A-B repeat pause mode is
active.
[DL]:
Indicates that the playback images are currently
being downloaded.
[END]:
Indicates that download of the playback images
has ended.– [Step 1] – [Step 7]:
Indicates the playback speed.
Step 1:Normal playback speed 
Step 2:Approx. 4x playback speed 
Step 3:Approx. 8x playback speed 
Step 4:Approx. 16x playback speed 
Step 5:Approx. 32x playback speed 
Step 6:Approx. 48x playback speed 
Step 7:Approx. 96x playback speed 
[SEQ]:
Indicates that the sequence display is currently
being performed.
[HDD]:
Indicates that playback of a recorded image
stored in the normal recording area or the event
recording area of the built-in hard disk of this unit
is currently being selected.
[HDD COPY]:
Indicates that the HDD copy area is currently
being selected.
[RECOVER]: 
Indicates that RAID recovery is currently being
performed.
[FILTERING]:
Indicates that the recording event list is filtered.
Refer to the Operating Instructions (PDF) for fur-
ther information about filtering of the recording
event list.
wIndicator
The status of recording will be displayed.
When lit red:Indicates that recording is being per-
formed.
When not lit:Indicates that recording is not being
performed. 
						

							22
eIndicates the following statuses:
[BUSY]:
Indicates that the camera is not operable
because a user with higher priority is currently
operating that camera.
[COPY]:
Indicates that copying is being performed.
[DELETE]:
Indicates that deletion of a recorded image is
being performed.
rIndicates information about events and errors.
[ALARM SUSPEND]:
Clicking this button will temporarily disable alarm
detection. (Refer to the Operating Instructions
(PDF).)
[ALARM SUSPEND]:
This indication will be displayed while an alarm is
being suspended.
[ALARM RESET]:
Indicates an event occurrence. The alarm display
action will be canceled by clicking this button.
(Refer to the Operating Instructions (PDF).)
[ALARM RESET]:
Indicates no event occurrence.
[ERROR]:
Indicates an error occurrence.
Refer to the Operating Instructions (PDF) for fur-
ther information about error.
[ERROR]:
Indicates no error occurrence. 
						

							23
qIndicates the start time and the end time of a down-
load or a A-B repeat. (Refer to the Operating
Instructions (PDF).)
[Start] button
Indicates the start time for the time and date of
the image to be downloaded.
[End] button
Indicates the end time for the time and date of
the image to be downloaded.w[GO TO DATE] button
Indicates the time and date of a marked point. Use
this button to designate the desired time and date of
a recorded image to be played. (Refer to the
Operating Instructions (PDF).)
e[GO TO LAST] button
Skips to the latest recorded time of a recorded
image from the currently displayed camera channel
and plays it.
Playback Point Operation Area
[HDD] Tab
[REW] button
Fast reverse playback will be performed. Playback
speed for fast reverse playback will be changed in the
following order each time this button is clicked: Step2
(Approx. 4x) →Step3 (Approx. 8x) →
Step4 (Approx. 16x) →Step5 (Approx. 32x) →
Step6 (Approx. 48x) →Step7 (Approx. 96x)
[PREV RECORD] button
Skips to the previous recorded image and plays it.
[REV PLAY] button
Reverse playback of a recorded image will be per-
formed.
[PLAY] button
Playback of a recorded image will be performed.
[NEXT RECORD] button
Skips to the next recorded image and plays it.[FF] button
Fast playback will be performed. Playback speed will be
changed in the following order each time this button is
clicked: Step2 (Approx. 4x) →Step3 (Approx. 8x) →
Step4 (Approx. 16x) →Step5 (Approx. 32x) →
Step6 (Approx. 48x) →Step7 (Approx. 96x)
[PREV IMAGE] button
The previous frame will be displayed when this button is
clicked during playback/pausing.
[PAUSE] button
Playback will be stopped when this button is clicked dur-
ing playback. Playback will be resumed when this but-
ton is clicked during pausing.
[STOP] button
Stops playback and displays a live image.
[NEXT IMAGE] button
The next frame will be displayed when this button is
clicked during playback/pausing.
qwe 
						

							24
[A-B Repeat] box
The A-B repeat playback will be performed.
[START] button
Starts repeated playback of images between the A-B
repeat start/end points. 
Date and time of the A-B start/end points will be dis-
played in the playback position operations area. 
[Cancel] button
The A-B repeat playback will be canceled.
[Download (TO PC)] box
Downloads the image currently playing to a PC.
[Download] button
Displays the download setting window for download-
ing images.
Date and time of the download start/end points will
be displayed in the playback position operations
area. 
[VIEWER] button
Clicking this button will start downloading the viewer
software that can play downloaded images.
[TEXT] button
The attached text information will be displayed when
this button is clicked during pausing.
[REC] box
The recording button, the recording stop button and the
SD memory data obtain button will be displayed when
the  button is clicked.
Displaying the recording button, the recording stop but-
ton and the SD memory data obtain button will be
unavailable when the  button is clicked.
SD memory data obtain button:Obtains
recorded images on the SD memory card on the
camera. The letters SD on this button will be displayed
in red when there are recorded images on the SD
memory card. The letters SD on this button will be
displayed in blue when there is no recorded image on
the SD memory card. When this button is clicked while
the letters SD are displayed in blue, the unit will check
if there is any recorded image on the SD memory card
or not. When a recorded image is found, the letters SD
on the SD memory data obtain button will turn red.
Recording button:Starts manual recording.
Recording stop button:Stops manual recording.
Important:
•To display the recording button and the recording
stop button, hold down the  button until they are
displayed.
Note:
When played image is in MPEG-4 format, results
from operating the some buttons will be as follows.
[GO TO DATE] button:Playback sometimes may
start from a point several seconds after the des-
ignated time and date.
[REV PLAY] button:Some frames of recorded
images will not be displayed. Reverse playback
will be performed with the set refresh interval of
the camera.
[PLAY] button (during playback):When the
[PLAY] button is clicked during playback, images
will be skipped for several seconds. (Playback
will starts from a point several seconds after the
current point.)
[PREV IMAGE] button:Some frames of recorded
images will not be displayed. Reverse frame play
will be performed with the set refresh interval of
the camera.
[FF]/[REW] button:Some frames of recorded
images will not be displayed. Fast playback/fast
reverse playback will be performed with the set
refresh interval of the camera.
[START] button (in the [A-B Repeat] box):Black
screen may be displayed when the A-B repeat
playback is performed.
[Download] button (during playback):Download
may start from a point several seconds later than
the designated start time and may end at a point
several seconds after the designated end time
when downloading MPEG-4 images. 
						

							25
[Zoom] box
Zooming can be adjusted by clicking the 
[Wide] button or the  [Tele] button.
[Focus] box
Focusing can be adjusted by clicking the  [Near]
button or the  [Far] button.
The auto focus function can be performed by clicking
the [Auto] button.
[Auto mode] box
This box allows users to select the auto mode function
and operate the camera.
Click the  button to select the auto mode function
(Auto Track, Auto Pan, Preset Sequence, Sort, or
Patrol) of the camera, and click  [Start] button.
Control pad/buttons
Clicking the buttons around the control pad can move
(pan/tilt) a camera in the clicked direction. Clicking
inside the control pad also can adjust the vertical/hori-
zontal position (pan/tilt) of the displayed image.
Panning/tilting speed will be faster if a clicked point gets
farther from the center point of the control pad.[Brightness] box
The brightness can be adjusted by clicking the 
[Close] button or the  [Open] button. It is possible
to reset the set brightness by clicking the  [Reset]
button.
[Preset] box 
This box allows users to register the current camera
direction on a specified preset position. Aim the camera
at a direction to be registered, click the  button to
select a preset number (1-256), and click the 
[Program] button.
Move the camera to the preset position registered in
advance. Click the  button to select the preset number
and click the  [Go] button.
[CAM] Tab
Control pad/buttons 
						

							26
Setup items
Display Setup
Camera Setup
Rec & Event Setup
Network SetupDescription
Perform the display settings such as the display position of the camera
title and time, and the settings for other basic operations of this unit.
For performing camera network settings and group settings. 
Perform the basic settings for recording operation and for event action.
Settings for a network can be performed.Page
28
30
31
35
Setup Menu (Quick)
Performing each setting item on the setup menu should be completed in advance to operate this unit.
The setup menu operations are performed from the [Setup] tab.
Using the setup menu (Quick) and the setup menu (Advanced). First, check the settings items of the setup menu
(Quick) and perform the settings. When more detailed settings are required, perform the settings on the setup menu
(Advanced). Refer to page 37 for further information about the setup menu (Advanced).
The following are available on the setup menu (Quick).
Setup Menu (Quick) Chart
Basic Operation with the Setup Menu (Quick)
Screenshot 1
Start operation from the top page.
Step 1
Click the [Setup] tab. 
						

							27
Screenshot 2
The setup menu (Quick) will be displayed.
Step 2
Click an item on the setup menu (Quick).
Note:
When ADVANCED is selected for REC Type of
Rec & Event Setup on the setup menu (Quick)
(page 32) the setup menu (Advanced) will be dis-
played when the [Setup] tab is clicked. In this case,
click Quick Setup Menu. The top page of the setup
menu (Quick) will be displayed.
Screenshot 3
The settings page of the selected menu will be dis-
played in the image display area.
Step 3
Perform the settings for each item.
Click the [SET] button after completing the settings.
When the [CLEAR] button is clicked, the contents of the
settings will be cleared.
Step 4
To complete the settings, click the [Registration] button.
→The settings will be applied.
Important:
•If the settings are applied, all login users will be
forcibly logged out.
•The settings will not be applied by clicking the [SET]
button in step 3. To apply the settings, click the
[Registration] button on the setup menu (Advanced).
•Recording is interrupted for about 4 seconds after
changing the settings and clicking the [Registration]
button. 
•If an unnecessary status bar or scroll bar is dis-
played in the popup window, see page 101.
Menu 
						

							28
Language
Select the display language for the web browser from
the following.
JAPANESE/ENGLISH/FRANÇAIS/ESPAÑOL/
DEUTSCH/ITALIANO/RUSSIAN/CHINESE
Date Format
Select a date format to be displayed from the following.
Example: (Ex. April 1, 2007)
YY.MM.DD:07.04.01
MMM.DD.YY:APR.1.07
DD.MMM.YY:1.APR.07
Time Format
Select a time format to be displayed from the following.
(Example for 3 o’clock in the afternoon)
12h:3:00:00PM
24h:15:00:00
Time & Date
Adjust the current time and date.
Select numbers for year, month, day, hour, minute and
second, and click the [SET] button on the right.
Summer Time (Daylight Savings)
Perform the settings for summer time from the following.
OUT:Does not function.
AUTO:Applies summer time in accordance with the set-
ting of summer time. (Refer to pages 44 and 45 for
the descriptions of how to perform the settings.)
Sequence Setup
Perform the settings for the sequential display of live
images.
The following window will be displayed when the
[SETUP] button is clicked.
Display/System Settings [Display Setup]
Perform the time and date, display settings such as the time and date display, the camera title display, the sequen-
tial display and the language setting.
Screenshot 1
Click Display Setup on the setup menu (Quick) to dis-
play the display settings window.
Step 1
Perform the settings for each item. Refer to the follow-
ing for further information about the settings for each
item.
Step 2
Click the [SET] button after completing the settings.
Important:
Live images will turn to black screen and recording
will not be performed for around 4 seconds just after
changing the time and date settings such by editing
the time and date settings or by shifting to/from sum-
mertime. 
Setup items 
						

							29
Select SPOT or 4 Screens as the sequence. 
Clicking the [SET] button for the selected sequence will
display the following window for setting the various
items. Click the [SET] button after completing the set-
tings, and close the window by clicking the [×] button at
the top right of the window.
[CAM]
Select a camera image to be displayed at each step
from the following.
--:Skips the selected step.
CAM1 - 32:Displays an image from the selected cam-
era channel on a single screen.
4A - 4H:Switches the images of the preset camera
groups (A – H) of 4 channels in sequence on a 4-
Screen, starting from A. 
Camera groups can be set from [System] – [Basic
Setup] – [Monitor Display] on the setup menu
(Advanced) (page 42).[PRESET]
Enter a camera preset position (blank, 1 to 256). When
no position is entered (blank), the camera does not
move to any preset position.
[DWELL]
Select an interval time to go to the next sequential step
from 1 - 30 seconds (in 1 second intervals). 
						

							30
Camera Network Settings and Group Settings [Camera Setup]
Performs network settings such as camera IP address and port number, and group settings.
Screenshot 1
Click Camera Setup on the setup menu (Quick) to dis-
play the camera setting window.
Step 1
Click the [SETUP] button and perform the settings for
each item.
Refer to the following for further information about the
settings for each item.
Setup items
NW Camera Setup
Perform the network camera settings such as the cam-
era IP address and the port number. The following win-
dow will be displayed when the [SETUP] button is
clicked.
Click the [SET] button after completing the settings, and
close the window by clicking the [×] button at the top
right of the window.[Manufacturer]
Select the manufacturer of the camera.
[MODEL/COMPRESSION]
Select a camera number and image compression
method.
[ADDRESS]
Enter an IP address. Enter up to 255 alphanumeric
characters.
[Port Number]
Set the http port number used by the camera. A number
from 1 - 65535 is available.
[GROUP]
Select the group to which the camera is assigned (G1 -
G8).
[CAM TITLE]
Set the camera title displayed on the [Cam Select] tab,
etc. Enter up to 16 alphanumeric characters except the
following: ! $ %  < = > @ [  ] ^ _ ` { | } ~