Panasonic Network Camera Wv Sud638 Operating Instructions

							When the registration window is not displayed, check that the PC is being connected to the Internet,
and click the reload button of the browser.
3. Register the information for “Viewnetcam.com” by following the instructions of the wizard.
→ When the message  “The new camera is successfully registered to Viewnetcam.com ” is displayed, close
the registration window.
The URL set at the time of registration can be used for camera access. However, this URL is unavailable
when accessing the camera from the PC connected to the same network (LAN).
Note
•When the registration for the “Viewnetcam.com” service is completed, the URL registered for
“Personal( Camera) URL ” is displayed. It may take up to about 30 minutes until the URL of the registered
camera is validated.
• To cancel the enrollment in the “Viewnetcam.com” service, access the “Viewnetcam.com” website
(http://www.viewnetcam.com/) later.
• When “Expired” is displayed in the URL of “Viewnetcam.com” in the viewnetcam settings page or the
status page, restart the camera after registering the “Viewnetcam.com” service. After restarting the
camera, check that the registered URL is displayed in the URL of “Viewnetcam.com” of [Status] -
[Viewnetcam.com] on the “Maintenance” page.
• It is possible to check the information registered for the “Viewnetcam.com” service by accessing the
URL displayed beside  “Your Account Link ”. When the URL is not displayed, check that the PC is being
connected to the Internet, and click the [Set] button.
• If access often fails due to the change in the global address of router, set a smaller value for “Access
interval”.
Operating Instructions171
12 Configuring the network settings [Network]     
						

							12.6.4  Checking the information registered for the
“Viewnetcam.com” service
It is possible to check if the camera has been registered for the “Viewnetcam.com” service. ( ®page 184)
12.6.5  When using “Dynamic DNS Update”
[Host name]
Enter the host name to be used for the Dynamic DNS Update service.
• Available number of characters:  3 - 250 characters
Enter in the form of “(host name). (domain name)”.
• Available characters:  Alphanumeric characters, the colon (:), the period (.), the underscore (_), and the
hyphen (-).
• Default:  None (blank)
Note
•Refer to the network administrator for further information about the available host names.
[Access interval]
Select the interval to access the Dynamic DNS Update service server to check the IP address and the host
name from the following.
10min/ 20min/ 30min/ 40min/ 50min/ 1h/ 6h/ 24h
• Default:  24h
12.6.6  When using “Dynamic DNS Update(DHCP)”
172Operating Instructions
12 Configuring the network settings [Network]     
						

							[Host name]
Enter the host name to be used for the Dynamic DNS Update service.
• Available number of characters:  3 - 250 characters
Enter in the form of “(host name). (domain name)”.
• Available characters:  Alphanumeric characters, the colon (:), the period (.), the underscore (_), and the
hyphen (-).
• Default:  None (blank)
Note
•Refer to the network administrator for further information about the available host names.
Operating Instructions173
12 Configuring the network settings [Network] 
						

							13   Configure the settings relating to the
schedules [Schedule]
On the “Schedule” page, it is possible to configure the settings relating to schedules as follows.
• Alarm permission
• VMD permission
• Access permission
• Audio detection permission
• Scene file (image 1, image 2)
• FTP periodic image transmission
• Position refresh
• Preset position (1-256)
• All detect permission (only when Viewnetcam.com is used)
The “Schedule” page has only the [Schedule] tab.174Operating Instructions
13 Configure the settings relating to the schedules [Schedule] 
						

							Up to 5 schedules can be set.
1.Select an action to be assigned to the schedule from “Schedule mode”.
“Off” is selected at the default.
• Off:  No action will be taken for the respective schedule.
• Alarm permission:  Alarm input (terminal alarm) will be received during the period of the schedule.
• VMD permission:  The video motion detection (VMD) function will be active during the period of the
schedule.
Operating Instructions175
13 Configure the settings relating to the schedules [Schedule]   
						

							•Audio detection permission:  The audio detection function will be active during the period of the
schedule.
• Access permission:  Users whose access level is set to 2 and 3 on the [User auth.] tab
( ® page 121) can access the camera only in the period of schedule.
• Position refresh : The camera position will be refreshed at the designated time in the schedule.
• 1-256 : The camera will move to the designated preset position at the designated time in the schedule.
• All detect permission:  When “Viewnetcam.com” is selected for “DDNS”, only “Schedule 5” can be
selected. Alarm input is allowed during the period of the schedule. However, the schedule cannot be
changed.
• Image adjust 1:  Scene 1:  Images are set to the image settings of  “Scene file 1 ” at the designated time
in the schedule. When the designated time for the schedule finishes, images are set to the image
settings of “Scene file is not applied”.
• Image adjust 2:  Scene 2:  Images are set to the image settings of  “Scene file 2 ” at the designated time
in the schedule. When the designated time for the schedule finishes, images are set to the image
settings of “Scene file is not applied”.
• FTP periodic image transmission:  FTP periodic image transmission will be performed at the
designated time in the schedule.
Note
•Select “On”  for “User auth.”  on the [User auth. ] tab of “User mng.”  page (® page 121 ) and “Off” for
“Host auth.” on the “Host auth.” page ( ®page 122) to validate “Access permission”.
2. Select days of a week by checking the respective checkboxes.
3. From the pull-down menu, select the start time and the end time of the schedule.
When not designating time, check the checkbox of “24h”.
4. Click the [Set] button after completing the settings.
→ The result will be displayed at the bottom of the window.
Note
•The schedules displayed at the bottom of the window can be identified by colors assigned to each
schedule.
• If the schedules for position refresh and image quality are set to the same times, the action for image
quality will be performed after the action for position refresh is finished.
176Operating Instructions
13 Configure the settings relating to the schedules [Schedule] 
						

							13.1  How to set the schedules
1.Check the check box of the desired day of the week.
→ The selected day of the week will be validated for the schedule.
2. To designate time, select the desired “hour” and “minute” from the pull-down menu.
When not designating time, check the checkbox of “24h”.
Operating Instructions177
13 Configure the settings relating to the schedules [Schedule]   
						

							3.Click the [Set] button after completing the settings.
→ The result will be displayed at the bottom of the window.178Operating Instructions
13 Configure the settings relating to the schedules [Schedule]   
						

							13.2  How to delete the set schedule
1.Uncheck the check box of the set day of the week.
Operating Instructions179
13 Configure the settings relating to the schedules [Schedule]   
						

							2.Click the [Set] button after completing the settings.
→ The schedule of the selected day of the week is deleted.180Operating Instructions
13 Configure the settings relating to the schedules [Schedule]