Panasonic Network Camera Kx Hcm270 Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 21
2.4 Network Parameters
2.4.1 Preparing the Network Parameters for Network
Camera
Before starting to set up the network parameters of Network Camera, make note
of corresponding network parameters.
Refer to page 22 and page 23 for network parameters.
Network parameters memo for Network Camera
The devices on the network may not be assigned the same IP address. Each
device must have its own IP address. Overlapped IP addresses can cause other
network devices to stop working and may result in widespread network problems. [Ty p e 1]Ask your network administrator for the network parameters.
[Ty p e 2]Refer to the broadband router’s manual for the network parameters.
[Ty p e 3]Ask your ISP (Internet Service Provider) for the network parameters.
[Ty p e 4]Install Network Camera in the default condition. Set the PC
192.168.0.250 (IP address) and 255.255.255.0 (Subnet Mask).
Refer to page 24.
Default Gateway...
DNS Server 1 . . . IP Address . . .
DNS Server 2 . . .
Subnet Mask . . . 
						

							Operating Instructions
22
Network Parameters Table
*
1Many ISPs intentionally block port number 80 to guard against network
viruses. If your ISP blocks port number 80, substitute it to another unused port
number.
*
2When you use more than one Network Camera with a broadband router, each
Network Camera needs its own port number. The broadband router needs the
Port Forwarding feature. Refer to page 37.
*
3Refer to the broadband routers manual for the Port Forwarding feature.
*
4When you use Network Camera in DHCP feature, check [DHCP] and enter the
Host Name if your ISP requires. If you automatically get the address of Default
Gateway and DNS server from DHCP server, you do not need to set up.
*
5Verify that your ISP supports DHCP. If your ISP supports DHCP, or if you
assign a domain name to Network Camera, you need to contract and register
for DDNS service. Refer to the included leaflet for DDNS service. If you set
static global IP address to Network Camera and the broadband router, you do
not need to register DDNS service.
It can restrict the transmit bandwidth.
Select from 0.1 to Unlimited Mbit/s. Max.
Bandwidth
Usage
ParametersNetwork Camera Configuration Type
Por t No.
IP address
Subnet
Mask
Default
Gateway
DNS
Server 1, 2
DDNSCheck [Static],
and set the
static private
IP address.192.168.0.253
(default)
255.255.255.0
(default) Check [Static],
and set the
static global
IP address.*
4
Check [Static],
and set the
static private
IP address.*
3
Set Default
Gateway
address.Youdonot
need to set up.
Set DNS server address.[Type 1] [Type 2] [Type 3] [Type 4]
Set Default
Gateway
address.*
4
Set DNS server
address.*4
Set the private
IP address of the
broadband router
(on your network),
not of the gateway
of your ISP. *
3
80 (default)*180 (default) 80 (default)
Set the Subnet Mask fitted to your network.
Youdonot
need to setup.Youdonot
need to setup. *
5*5
80 (default)*1*2 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 23
How to refer the network parameters from the PC
If you cannot get the network parameters, you can refer to the network parameters
except for IP address from the PC on the same network in the following procedure.
When using Windows 95,Windows 98 or Windows Me
1.Click[Start]–>[Run...].Run windowappears.
These steps are slightly different depending on the operating system.
2.Enter winipcfgandclick[OK].IP configuration windowappears.
3.Select the proper Ethernet adaptor and click[More Info].
4.Click[OK]to close IP Configuration window.
When using Windows NT,Windows 2000 or WindowsXP
1.Click[Start]–>[Program](–>[Accessories])–>[MS-DOS®(Command)
Prompt].MS-DOS Prompt windowopens. These steps are slightly different
depending on the operating system.
2.Enter ipconfig /all and press[Enter].
3.Enter exit and press[Enter]to close the window. 
						

							Operating Instructions
24
2.4.2 Setting IP Address of the PC in[Ty p e 4]
Configuration Type
Your PC needs to have a static private IP address to access Network Camera in
[Typ e 4]configuration.
1.Follow the steps below, appropriate for your operating system to openTCP/IP
Properties windowon the PC.
Note
When using Windows NT, Windows 2000 and Windows XP, log on as an
administrator to accessTCP/IP Properties window. TCP/IP Properties Table
Operating
SystemSteps
Windows 95
Windows 98
Windows Me[Start]–>[Settings]–>[Control Panel]–>[Network]–>
Select[TCP/IP]with adaptor in use–>[Properties]–>
[Specify an IP address]
Windows NT[Start]–>[Settings]–>[Control Panel]–>[Network]–>
[Protocols]tab–>[TCP/IP Protocol]–>[Properties]–>
Select[Adaptor]in use–>[Specify an IP address]
Windows
2000[Start]–>[Settings]–>[Control Panel]–>[Network and
Dial-up Connections]–>[Local Area Connection Icon]in
use–>[Properties]–>Select Internet Protocol[TCP/IP]
–>[Properties]–>[Use the following IP address]
Windows XP[Start](–>[Settings])–>[Control Panel]–>[Network and
Internet Connections]–>[Network Connections]–>
[Local Area Connection Icon]in use–>[Properties]–>
Select Internet Protocol[TCP/IP]–>[Properties]–>[Use
the following IP address] 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 25
2.TCP IP Properties windowappears. Set 192.168.0.250 in the IP address
data field and 255.255.255.0 in the Subnet Mask data field.
3.Click[OK].
Private IP address
Private IP address is the network ID that is not used on the Internet. They are
classified into Class A, Class B and Class C, as shown in the next table. Set the
IP address in the range of the number specified in the class meeting to your local
network scale.
Class Subnet MaskPrivate IP address (It can be set freely within
the range in your group.)
Class A 255. 0. 0. 0 10. 0. 0. 1 — 10. 255. 255. 254
Class B 255. 255. 0. 0 172. 16. 0. 1 — 172. 31. 255. 254
Class C 255. 255. 255. 0 192. 168. 0. 1 — 192. 168. 255. 254 
						

							Operating Instructions
26
2.5 Proxy Server Setting
A proxy server may prevent you from connecting directly to Network Camera in
some corporate environments. The web browser can set up the IP address
communication without using a proxy server. Consult your ISP or network
administrator.
Note
A proxy server is generally used to maintain security on a network that offers
an Internet connection. The network of Network Camera with the proxy server
may cause some problems to the image quality such as taking much time in
refresh interval. Consult your ISP or network administrator for details.
1.Start up the Internet Explorer. (The window is Internet Explorer 5.50.)
2.Select[Tools]–>[Internet Options...]–>[Connections]taband click[LAN
Settings].SeeiftheUse a proxy servercheck box is checked or not in the
next window. When checked, click[Advanced...].
When not checked, click[Cancel]. Your proxy settings are causing no
problems.
See if the check
box is checked or not.
When checked, click
[Advanced...]. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 27
3.Enter the IP address of Network Camera assigned from your ISP or network
administrator into theDo not use proxy server for addresses beginning
withdata field.
4.Click[OK]on all of the opening windows. 
						

							Operating Instructions
28
2.6 Simple Installation using the Setup CD-ROM
After finishing cabling, turn on Network Camera and insert the Setup CD-ROM in
the CD-ROM drive of the PC. Setup CD-ROM should start the application
automatically. This program automatically finds Network Cameras on the network.
1.Turn on Network Camera.
2.Insert the Setup CD-ROM in the CD-ROM drive of the PC.
(IfNetwork Camera Setup windowdoes not appear, click setup.exe on the
Setup CD-ROM.) 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 29
3.Click[Network Configuration]. Network Camera List windowappears.
Setup program finds all Network Cameras connected on your local network. It
lists all of MAC addresses and IP addresses of Network Cameras. Network
Cameras that are isolated by the use of a home gateway or broadband router
will not be detected. Record MAC address on the Network Camera Memo on
page 3. It is useful for customer servicing.
Notes
 The setup program finds and identifies Network Camera by listening for
data, which Network Camera sends out for the first 20 minutes after
powering up. If the installation is not completed within 20 minutes,
disconnect temporarily the AC adaptor to restart this operation.
 Each Network Camera has a unique MAC address labeled on the back.
Refer to page 15.
 Network Cameras that are isolated by the use of a home gateway or
broadband router will not be detected.
(A) 
						

							Operating Instructions
30
4.Select your target Network Camera from the list as shown in example(A)on
Network Camera List windowonpage29andclick[Select].Configuration
windowappears. Refer to page 21 and page 22 and enter the correct network
parameters. Refer to page 59 for details of each parameter.
5.Click[Save]when finished. The Successful! message box appears.
Notes
 Network Camera automatically restarts after saving the network
configuration.
 Overlapped IP address displays the next box. If you cannot set up, ask your
ISP or the administrator.