Panasonic Network Camera Bb Hcm381a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 81
2.14 Creating, Modifying or Deleting General Users
The General User page allows you to create, modify or delete general users. Up to 
50 general users can be registered. The access level is set for each general user. 
If you set [Permit access from guest users] on the Security: Administrator page, the 
access level can be set for guest users.
Note
 For general users, the Setup and Maintenance tabs are...

Operating Instructions
82
4.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed.
SettingDescription
User ID List Up to 50 general users can be registered.
 The list is used to modify or delete general user settings.
User Name/
Password User Name (6 to 15 characters): Enter the user name.
 Password (6 to 15 characters): Enter the password.
Note
The password must be different from the user name.
 Retype Password: Reenter the password.
 Enter ASCII characters...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 83
5.Click [Go to General User page]. 

Operating Instructions
84
2.15 Changing Initial Settings on the Single 
Camera page or the Multi-Camera page
The Image Display page allows you to change initial settings (display settings when 
a user accesses the camera) of image resolution, image quality and refresh 
interval. You can display a time stamp on the image. The initial language can be 
selected from eight languages. The banner can be displayed for administrator or 
general users or both.
1.Click [Image Display] at the top of the page.
2.Set...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 85
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed.
SettingDescription
Image Resolution Select the image resolution.
640 x 480 pixels (Only for the Single Camera page)
320 x 240 pixels (default)
160 x 120 pixels (Only for the Multi-Camera page)
Image Quality Select the image quality.
[Favor Clarity] optimizes for good quality.
[Standard] offers standard...

Operating Instructions
86
4.Click [Go to Image Display page].
 The Image Display page is displayed. 

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 87
2.16 Configuring Multiple Cameras
The Multi-Camera Setup page allows you to configure the camera IP addresses 
and camera names to view multiple images on the Multi-Camera page. These 
configurations are required to use the Multi-Camera page. Up to 12 cameras can 
be configured.
1.Click [Multi-Camera] on the Setup page.
2.Click [Add].
Note
 If you click the camera number, the modification page is...

Operating Instructions
88
Note
 Set the local IP address and port number for the camera on the same 
LAN.
 If the cameras will be accessed from the Internet, be sure to use the global 
IP address. In this situation, local IP addresses such as 192.168. x.x 
cannot be used.
4.Click [Save] when finished.
 New settings are saved.
 The Multi-Camera Setup page is displayed.
SettingDescription
Display Check the box to enable the camera.
IP Address*1 or 
Host Name*2 Set the IP address or the host name to...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 89
2.17 Format the SD memory card
Before you record the camera image, you need to format the SD memory card.
Note
 You can confirm the SD memory capacity on the Status page (see page 
118).
1.Insert the SD memory card (see page 36 of the Installation/Troubleshooting).
2.Click [Buffer/Transfer] on the Setup page.
3.Click [Format].
4.Click [OK] on the confirmation window.
 Format is complete.
5.Click [Go...

Operating Instructions
90
2.18 Stop the SD Memory Recording
After you stop the SD memory recording, remove the SD memory card.
Note
 You can confirm the SD memory capacity on the Status page (see page 
118).
1.Click [Buffer/Transfer] on the Setup page.
2.Click [SD video recording stop].
3.Click [OK] on the confirmation window.
 The SD memory recording is stopped.
4.Click [Go to Image Buffer/Transfer page].
 The Image Buffer/Transfer page is displayed.
Note
 If the camera is restarted (see page 119),...