Panasonic Network Camera Bb Hcm381a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 61
7.Click [Restar t].
8.Set up your VPN router as shown below.
 To use tunnel mode, you need to set up your VPN router.
SettingDescription
IPsec Check the box to enable IPsec features. If you clear the 
box, whole IPsec features will be invalid.
Encoding strength Encoding strength for IPsec can be selected. If you select 
[Standard], DES or NULL is valid as an algorithm, and then 
the data will become...

Operating Instructions
62
 Set up the IPsec policy as the following.
9.Access the camera (see page 13).
 If you can access the camera, the IPsec setup is complete.
Note
 In IPsec communications, IPsec is displayed on the Top page or the 
Single Camera page.
 If you cannot communicate using IPsec, see 2.9 IPsec in the 
Troubleshooting section of the Installation/Troubleshooting.
 See the Panasonic Network Camera support website at 
http://panasonic.co.jp/pcc/products/en/netwkcam/ for the IPsec...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 63
2.7 Using UPnP™ (Universal Plug and Play)
UPnPTM can automatically configure your router to be accessed from the Internet. 
In order to use this feature, your router needs to support this feature and it must be 
enabled. Most router manufacturers disable this feature as the default setting. See 
http://panasonic.co.jp/pcc/products/en/netwkcam/technic/rtr_setup/ for 
details and see your router manual...

Operating Instructions
64
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed. 
4.Click [Go to UPnP page].
 The UPnP page is displayed. 

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 65
2.8 Registering with the Viewnetcam.com service
Viewnetcam.com is a free service (dynamic DNS service) that allows you to assign 
an easy to remember name to the camera, similar to your favorite web site. 
Viewnetcam.com also allows you to easily access the camera, even when your ISP 
changes the IP address. Panasonic Communications recommends you to register 
with it for the Internet access to the...

Operating Instructions
66
Note
 When the Viewnetcam.com registration website is not displayed, confirm 
that the URL is displayed in the right column of the Your Account Link. If 
the URL is not displayed, follow the procedures below.
 Personal (Camera) URL is available after you registered with the 
Viewnetcam.com service.
 If port forwarding is not enabled or your network is not connected to the 
Internet, the Viewnetcam.com service is not available.
6.Register with the Viewnetcam.com service...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 67
2.9 Setting Date and Time
The Date and Time page allows you to set date and time. Date and time are used 
for image buffer/transfer, operation time and time stamps on the buffered image.
Note
Saving the date and time settings deletes all buffered images on the internal 
memory. The buffered images on the SD memory card are not deleted.
1.Click [Date and Time] on the Setup page.
2.Set each parameter.
...

Operating Instructions
68
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed.
4.Click [Go to Date and Time page].
 The Date and Time page is displayed.
Note
Date and time settings become incorrect depending on the length of power-on 
time or the internal temperature. Using the Automatic Time Adjustment is 
recommended. 
SettingDescription
Time Setting Select date and format (AM/PM or 24 H). These settings 
are used for image buffer/transfer, operation time...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 69
2.10 Changing Camera Settings
The Camera page allows you to set the camera name, white balance, AC power 
source frequency, automatic focus range, mounting type, pan/tilt range, return to 
specified position, color night view, and vertical resolution settings.
1.Click [Camera] on the Setup page.
2.Set each parameter.
 Clicking [Cancel] cancels your settings without saving changes.
NetworkCamera
Auto...

Operating Instructions
70
SettingDescription
Camera Name The camera name is displayed on the Single Camera 
page.
 Enter ASCII characters (see page 150) or characters in 
each language (1—15 characters for a 1-byte character 
and 1—7 characters for a 2-byte character). But [Space], 
[], [], [&], [] are not available.
White BalanceSelect from the following options.
 Auto (default)—Automatic adjustment
 Fixed Indoor—Electric bulb (2800 K) 
 Fixed Fluorescent 
(White)—White (3600 K)
 Fixed Fluorescent...