Panasonic Network Camera Bb Hcm381a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 111
2.21 Transfer the Camera Image in Transport Mode
The camera can transfer the image in transport mode by E-mail or FTP.
Prepare the following requirements.
See page 56 and set up the E-mail or FTP server.
ItemSupported Feature
E-mail or FTP 
ServerOperating 
System
ISP Service
: IPsec supported
: Services for multiple static global 
addresses (A global address must be set up 
to the server.)
CameraISP...

Operating Instructions
112
2.22 Transfer the Camera Image in Tunnel Mode
The camera can transfer the image in tunnel mode by E-mail or FTP.
Prepare the following requirements.
See page 59 and set up the E-mail or FTP server.
ItemSupported Feature
VPN RouterISP Service
(in IPv4)
ISP Service
(in IPv6)
: Services for static global addresses (A 
global address must be set up to the WAN 
side.)
: IPv4/IPv6 Dual-Stack or IPv6 over IPv4 
Tunneling service
CameraISP Service
(in IPv4)
ISP Service
(in IPv6)
:...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 113
2.23 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The camera image 
turns to a gray screen outside the operation time.
Note
 If you wrongly set the time period, your privacy may be seen. Confirm the 
time period after the setup.
 If you access the camera as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the...

Operating Instructions
114
4.Click [Save] when finished.
 New settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.
Note
An administrator can view images anytime regardless of the setting for the 
operation time.
SettingDescription
Enable...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 115
2.24 Controlling External Output Terminal
The digital output terminal allows you to control the external devices. You can 
change the initial status of the output signal.
1.Click [External Output] on the Setup page.
2.Click [Save] when finished.
 Clicking [Cancel] cancels your settings without saving changes.
 New settings are saved.
 When finished, Success! is displayed. 
3.Click [Go to External...

Operating Instructions
116
2.25 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
three options.
Always on
 Turn the indicator on when the camera is accessed.
Always off
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
 Clicking [Cancel] cancels your settings without saving changes.
Note
 See page 11 in the Installation/Troubleshooting for indicator display.
 Selecting [Never turn indicator on] keeps indicator...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 117
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(1)StatusDisplays the camera settings and status (see page 118).
(2)Session StatusDisplays information on access to the camera (see page 
118).
(3)RestartRestarts the camera (see page 119).
(4)Update FirmwareUpdates the camera firmware (see page 120).
(5)Save SettingsCreates a configuration file (see page 123).
(6)Load SettingsLoads settings from a...

Operating Instructions
118
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2 Confirming Session Status
Displays client information connecting to camera.
Clicking [Session Status] displays the following page....

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 119
3.1.3 Restarting the Camera
The Restart page can restart the camera. The camera can also be restarted by 
pressing the RESTART button or by disconnecting the power cord from the outlet 
and reconnecting it again.
Note
When the camera restarts, the buffered images will be deleted. The buffered 
images on the SD memory card are not deleted. 
1.Click [Restart] on the Maintenance page.
2.Click [Restar...

Operating Instructions
120
3.1.4 Updating the Camera Firmware
The Update Firmware page allows you to update the camera firmware. If the new 
firmware is available, install it into the camera.
Note
 Do not turn off the power during firmware update.
 All buffered images on the internal memory will be deleted after the 
firmware update. The buffered images on the SD memory card are not 
deleted.
 The firmware version is displayed on the Top page and the Status page.
1.Download the new firmware on the...