Panasonic Network Camera BB-HCM381A BB-HCE481A Getting Started Manual

							Operating Instructions
93
3.3 Creating, Modifying or Deleting General 
Users
The General User page allows you to create, modify or delete general users. Up to 
50 general users can be registered. The access level is set for each general user. 
If you set [Permit access from guest users] or [Permit access from guest users 
(mobile only)] on the Security: Administrator page, the access level can be set for 
guest users.
Note
 For general users, the Setup and Maintenance tabs are not displayed.
1.Click [General Users] on the Setup page.
2.To create a general user, click [Create].
 When setting [Do not permit 
access from guest users] When setting [Permit access 
from guest users] or [Permit 
access from guest users 
(mobile only)]
 To change the settings of general users or guest users, select their 
name and click [Modify]. The modification page is displayed.
 To delete a general user, select the name and click [Delete]. The 
confirmation page is displayed. 
						

							Operating Instructions
94
3.Set each parameter.
 Settings for general users  Settings for guest users
 Clicking [Cancel] takes you back to the previous page without 
saving changes.
Setting Description
User ID List  Up to 50 general users can be registered.
 The list is used to modify or delete general user settings.
User Name/
Password User Name (6 to 15 characters): Enter the user name.
 Password (6 to 15 characters): Enter the password.
Note
 The password must be different from the user name.
 Retype Password: Reenter the password.
 Enter ASCII characters (see page 190). Note that 
[Space], [], [], [&], [] and [:] are not available. 
						

							Operating Instructions
95
4.Click [Save] when finished.
 The new settings are saved.
 When finished, Success! is displayed.
5.Click [Go to General User page].
 The General User page is displayed.Setting Description
Access Level An access level is set for each general user. Check each 
feature to enable access to it.
 In the limit time of continuous Motion JPEG setting, set the 
time for changing video (Motion JPEG) to still images for 
each user. (Not permitted, Unlimited, 10 seconds—60 
minutes) In the refresh interval setting, set the refresh 
interval after the video has changed to still images. (3—60 
seconds)
 See the corresponding page for details of the following 
features.
Pan/Tilt Control (see page 25)
Zoom Control (see page 26)
Focus Control (see page 28)
Preset Control (see page 23)
Click to Center Control (see page 21)
Brightness Control (see page 24)
External Output Control (see page 24)
Change Refresh Interval (see page 24)
Change Resolution (see page 24)
Change Quality (see page 24)
Capture Image Button (see page 22)
Listen (see page 34)
Talk (see page 34)
View Multi-Camera page (see page 36)
View Buffered Image page (see page 38) 
						

							Operating Instructions
96
4 Buffering or Transferring Images
4.1 Procedures of Buffering or Transferring 
Images
The procedures from this page to page 130 are described about settings of the 
image buffer or transfer. See the procedures below to understand the general 
outline of the settings.
Buffer/Transfer by Timer 
(Page 97)
Transfer Method 
(Select one from the lists.)
 No Transfer, No Memory 
Overwrite
 No Transfer, Memory 
Overwrite
 FTP
 E-mailTransfer Method 
(Select one from the lists.)
 No Transfer, No Memory 
Overwrite
 No Transfer, Memory 
Overwrite
 FTP
 E-mailTransfer Method 
(Select one from the lists.)
 No Transfer, No Memory 
Overwrite
 No Transfer, Memory 
Overwrite
 FTP
 E-mail Buffer/Transfer by Alarm 
Signal (Page 107)
E-mail Notification When 
Triggered Setting
Changing Motion Detection 
Sensitivity (Page 133)
E-mail Notification When 
Triggered Setting
Notifying the Alarm Log 
(Page 137)Notifying the Alarm Log 
(Page 137) Buffer/Transfer by 
Motion Detection Signal 
(Page 119)
Time Setting
Image Setting
Image Buffer Frequency Setting
Time Setting
Image Setting
Image Buffer Frequency Setting
Save the settings to complete.
Save the settings to complete.
Time Setting
Image Setting
Lens Position When 
Triggered SettingLens Position When 
Triggered Setting
Image Buffer Frequency Setting
Save the settings to complete. 
						

							Operating Instructions
97
4.2 Buffering or Transferring Images by Timer
The Trigger page allows you to enable image buffer/transfer by E-mail or FTP.
Note
 If you are recording images to the SD memory card, refresh interval slows 
down.
1.Click [Trigger] on the Setup page.
2.Click a No. to enable buffer/transfer.
3.Check [Enable Image Buffer/Transfer], select [Timer] for the trigger, and click 
[Next>].
 Click [Delete Buffered Images] to delete images already buffered.
 Click [Save] to save the settings.
 Clicking [Cancel] takes you back to the Trigger page without saving 
changes.
Note
 If you click [Save], all buffered images on the SD memory card are 
deleted.
Setting Description
Enable Image 
Buffer/Transfer Check the box to enable the buffer/transfer. Uncheck the 
box to disable it. 
						

							Operating Instructions
98
4.Set the time, and click [Next>].
Note
The timer works by an internal clock. Set the date and time before using timer 
buffer/transfer (see page 77).
 Clicking [].
 Clicking [
						

							Operating Instructions
99
6.Set the image buffer frequency, and click [Next>].
 Clicking [
						

							Operating Instructions
100
7.Select the transfer method, and click [Next>].
 Clicking [
						

							Operating Instructions
101
When you set [FTP] for Transfer Method
Select [FTP], and click [Next>]. The following page is displayed.
 Clicking [
						

							Operating Instructions
102
Overwrite 
Setting Selecting [Overwrite File] overwrites the image on the server 
with a newer image. Selecting [Save as New File with Time 
Stamp] saves the image attaching time stamps on the file 
name, and the images are not overwritten.
E.g. image20050101093020500
.jpg
The underlined numbers mean 9h30min20s500ms on 
January 1, 2005. The letter s is inserted after the day when 
referring to a daylight saving time zone.
Data 
Transfer 
Method Select [Passive Mode] normally. If the transfer does not work, 
select [Active Mode] and check the operation.
*1 Note that [Space], [], [], [&], [] are not available.
*2 Note that [] is not available.
Setting Description