Panasonic Network Camera Bb Hcm311a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 101
2.22 Transfer the Camera Image in Tunnel Mode
The camera can transfer the image in tunnel mode by E-mail or FTP.
Prepare the following requirements.
See page 52 and set up the E-mail or FTP server.Item Supported Feature
VPN Router ISP Service
(in IPv4)
ISP Service
(in IPv6): Services for static global addresses (A 
global address must be set up to the WAN 
side.)
: "IPv4/IPv6 Dual-Stack" or...

Operating Instructions
102
2.23 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The camera image 
turns to a gray screen outside the operation time.
Notes
• If you wrongly set the time period, your privacy may be seen. Confirm the 
time period after the setup.
• If you access the camera as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the Setup page.
2.Click [No.] to set the operation time.
Note
If No. 1—7 are...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 103
4.Click [Save] when finished.
• New settings are saved.
• The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.Setting Description
Enable • Check the box to...

Operating Instructions
104
2.24 Controlling External Output Terminal
The digital output terminal allows you to control the external devices.
1.Click [External Output] on the Setup page.
2.Click [Save] when finished.
• Clicking [Cancel] cancels your settings without saving changes.
• New settings are saved.
• When finished, "Success!" is displayed. 
3.Click [Go to External Output Control page].
• The External Output Control page is displayed.Setting Description
External Device 
Control Output• If...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 105
2.25 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
three options.
•Always on
• Turn the indicator on when the camera is accessed.
•Always off
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
• Clicking [Cancel] cancels your settings without saving changes.
Notes
• See page 11 in the Installation/Troubleshooting...

Operating Instructions
106
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(14) StatusDisplays the camera settings and status (see page 107).
(15) RestartRestarts the camera (see page 107).
(16) Update FirmwareUpdates the camera firmware (see page 108).
(17) Save SettingsCreates a configuration file (see page 111).
(18) Load SettingsLoads settings from a configuration file (see page 112).
(19) Reset to Factory 
DefaultResets the camera to its default settings (see page 113).
(14)
(15)
(16)
(17)...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 107
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2Restarting the Camera
The camera restarts by disconnecting...

Operating Instructions
108
3.1.3 Updating the Camera Firmware
The Update Firmware page allows you to update the camera firmware. If the new 
firmware is available, install it into the camera.
Notes
• Do not turn off the power during firmware update.
• All buffered images on the internal memory will be deleted after the 
firmware update. The buffered images on the SD memory card are not 
deleted.
• The firmware version is displayed on the Top page and the Status page.
1.Download the new firmware on the...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 109
• The Update page is displayed in about a minute.
4.Click [Browse...].
• A dialog box is displayed to select the firmware.
5.Select the firmware (including directory information) and click [Open].
• The firmware file name is displayed.
6.Confirm the firmware file name, and click [Update Firmware].
• Clicking [Cancel] takes you back to the Top page without firmware update.
• The next message is...

Operating Instructions
11 0
7.Confirm that the version number on the Top page is updated.
• If the version number is updated, the firmware update is complete.
Updated version