Panasonic Mobile Stand For Plasma Display TY-ST58PF20 Installation Instructions

11
ÔŠ 

 

12
ÔŠ 
Óå¶ÚßµÓè Š.w	“Ž`Th



 ˆµ»ïÅwŠ.	“
ÇZ;Úé	Íw
ØtK”
Š.
HZw­;va(g(ÈŠ›	“Ž`oXi^M{











Óå¶ÚßµÓè Š.w<
æ›Ëj	Í[sU’
	
²t¾V‡b{



<w
ˆµÖ”±”UŽ•h’fw‡‡	ÍtËj
	Í[o	“Ž`‡b{Š.
HZw­;va(g

ˆµÖ”±”

  
 

　
　映像・ディスプレイデバイス事業グループ


13
English
WARNING
Installation and removal should only be carried out by a qualified technician.
• If the stand is not installed correctly, the Plasma display may fall over and become damaged, and 
personal injury may result.
Do not disassemble or modify the mobile stand.
•  Otherwise the unit may fall over and become damaged, and personal injury may result.
Set up in a location with little vibration that can support the weight of the unit.
•  Otherwise the unit may fall over or down, and personal...

14
Requests regarding handling
1)  Exercise care when selecting the location for the display because it may discolor or deform due to light 
or heat if it is placed where it is exposed to direct sunlight, or near a heater.
2)  For cleaning, wipe the display using a soft dry cloth (made of cotton or flannel). If the unit is extremely 
soiled, first wipe off soiling with a neutral detergent diluted in water, and then wipe with a dry cloth. Do 
not use cleaners such as benzene, thinner or furniture wax...

15
Main parts
English
Components
Check that all the parts are accounted for and 
present in their designated quantities.
  Base unit with casters (2)
 Base joint (1)
 Support column (left/right)
  (One for each side)
 Shelf plate (1)
 Bracket for shelf plate (2)
 Top bracket for plasma display (1)
 Bottom bracket for plasma display (1)
Accessory parts
  Hexagon socket cap button bolt (M8 × 65) 
Spring washer/Flat washer 
Cap nut with flange (M8)
 (Four each)  
Hexagon socket cap button bolt (M8...

16
1.  Assembling of the stand
2.  Attaching the support columns 
Preparing hexagon socket cap button bolts 
3.  Perpendicular adjustment and fixing of 
the support columns
  Adjust the suppor t columns (left /right) 
 so that 
they are perpendicular to the stand base. Tightly 
fasten the four hexagon socket cap button bolts 
 
that temporarily fixed the support columns.
  (Tightening torque: 8 to 10 N•m)
1.  Assembling the stand base
Preparing hexagon socket cap button bolts 

Ready four sets by...

17
5.  Preparation of the shelf plate
  
Face the unpainted side (back side) of the shelf 
plate 
 upward and place it on a soft cloth or the 
like. Align the positioning holes of the shelf plate 
with the bracket protrusions to position the two 
brackets for shelf plate 
, and attach them with 
four wood screws 
 through the outside holes.  
 (Tightening torque: 1 to 1.2 N•m)
 *  Do not excessively fasten the wood screws to 
prevent stripping screw holes. If a screw hole is 
stripped, use spare...

18
6.  Shelf plate fitting
 ●  Shelf plate fitting position can be adjusted for the top of 
the shelf plate to be either approx. 35 or 50 cm (13.8 or 
19.7 inches) from the floor.
  The figure shows an example of fitting to the upper level 
(50 cm [19.7 inches] from floor).
  Turn so the caution label of the readied shelf plate is 
on the back right, align the bracket for shelf plate 
 
screw holes and the support column 
 inside right 
and left screw holes, and fasten with four screws for 
fitting...

19
3. Fitting to the stand
Note
Before fitting the plasma display, make sure to lock the 
casters.
1.  Fitting plasma display
  Engage the upper insulation spacers of the 
plasma display with the cutouts at the top of the 
mobile stand, and slowly lower the plasma display 
into place.
  While lifting the plasma display slightly, insert the 
bottom insulation spacers into the holes at the 
lower end of the mobile stand, and then lower the 
plasma display straight down into place.
Caster locked
Push the...

20
4.  Setup and wiring of connected devices
  Insert the five clampers 
 in any of the six 
clamper attachment holes on the back side of  the 
left and right support columns at positions that 
make wiring easy. Wire as shown in the figure.
  Place cover stickers 
 in unused spare holes on 
the sides and back of the support columns and 
other locations. 
Note
Do not bundle the connection cables and main lead 
together.
5.  Preventing falling over
  In order to prevent the unit from falling over, fix...