Panasonic Memory Card Camera Recorder Ajhpx3000g Operating Instructions

101PreparationPower Supply
 Preparation
A battery pack or an external DC power supply can be used as AJ-HPX3000’s power supply.
Battery packs from the following manufacturers can be
used:
 Anton/Bauer
 IDX
 PA C O
 Sony
The type of the battery can be checked or changed
through the viewfinder or menu screen on the monitor.
zPressing the MODE CHECK button on the side of the
camera-recorder displays the current type of the battery
in the upper right corner of the viewfinder display.
zNavigate the menu...

102PreparationPower Supply
1Mount the Anton/Bauer battery pack.

The Anton/Bauer battery holder includes both a power
supply output connector for lighting and a lighting control
switch, which are convenient when attaching a light.
Please contact Anton/Bauer for information about the
lighting system. 
2Insert the battery and slide it in the direction of the 
arrow. 

Removing the battery pack 
Completely push down and hold the release lever on 
the battery holder. Then, slide the battery pack in the...

103PreparationPower Supply
 Preparation
1Remove the battery holder. 
2Mount the NP-1 type battery case on the camera-
recorder. 
1Tighten the mounting screws. 
2Tighten the power contact screws. 
3Insert the upper part of the removed cover in the 
direction of the arrow. 
4Align the holes in the bottom part (metal part) of 
the cover with the holes in the case, and secure the 
cover with the screw. 
‹Note
When mounting the battery holder, take care not to 
pinch the connection cord. When using a...

104PreparationPower Supply
1Connect the external DC power supply to the DC IN 
socket on the unit.
2Turn “ON” the power switch of the external DC power 
supply. (If the power switch is available on the external 
DC power supply)
3Turn ON the POWER switch on the unit.
‹Notes
zIf both the battery pack and the external DC power
supply are connected, the electric power is supplied
from the external DC power supply. While the
external DC power supply is used, the battery can
be mounted and removed on/from...

105PreparationMounting the lens and Performing the Flange Back and White Shading Adjustments
 Preparation
1Raise the lens clamping lever and remove the mount 
cap. 
2To mount the lens, align the indentation at the top 
center of the lens mount with the center mark of the 
lens. 
3Lower the lens clamping lever to clamp the lens. 
4Secure the cable through the cable clamp, and plug it 
into the LENS connector. 
5Adjust the lens flange back. 
‹Notes
zPlease refer to the lens instruction manual for...

106PreparationMounting the lens and Performing the Flange Back and White Shading Adjustments
8Repeat Steps 5 to 7 until the lens is in focus at both 
the telephoto and wide-angle positions. 
9Firmly tighten the F.f ring clamping screw. 
Method to correct the waveform to be more flat by 
combining the sawtooth-shaped waveform and the 
parabola waveform when watching the respective 
waveforms of R, G and B of the video signals.
Adjust the white shading in the following manner after
turning OFF the DS....

107PreparationMounting the lens and Performing the Flange Back and White Shading Adjustments
 Preparation
When making the white shading correction, make the
adjustment while observing the R, G, and B waveforms in
the horizontal and vertical directions with the waveform
monitor.
This now completes the white shading adjustments.
The adjustment values are now stored in the non-volatile
memory so that even when the unit’s power is turned off,
there will be no further need to perform the white shading...

108PreparationPreparing for Audio Input
Take the following steps to prepare the camera for connecting audio input devices. 
AJ-HPX3000 can be equipped with the AJ-MC900G stereo
microphone kit (an extra-cost option).
1Open the microphone holder. 
2Mount the microphone and tighten the clamping 
screw. The microphone must be attached with the UP 
mark on the microphone facing up.
3Connect the microphone cable to the MIC IN jack on 
the camera. 
4Set the AUDIO IN switch to [FRONT] depending on 
the audio...

109PreparationMounting the Camera on a Tripod
 Preparation
1Connect the audio device to the AUDIO IN jack with 
the XLR cable. 
2Set the AUDIO IN switch to [REAR] for the channel to 
which the XLR cable is connected. 
3Set the LINE/MIC/+48V selector switch on the rear 
panel to [LINE]. 
When mounting the camera on a tripod, use the tripod adapter supplied with the camera. 
1Mount the tripod adapter on the tripod. 
‹Note
Select an appropriate hole in the adapter, taking into 
account the center of...

110PreparationAttaching the Shoulder Strap
To detach the shoulder strap, first open the hooks, then
detach the strap. 
‹Note
Make sure that the shoulder strap is securely attached. 
Attaching the Shoulder Strap
Shoulder Strap 
Press to 
open the 
Attaching the Rain Cover
When using the SHAN-RC700 Rain Cover
Secure with the surface fastener
Tighten the cord 
Secure with the 
surface fastener
AJ-HPX3000G(VQT1D27)E.book  110 ページ  ２００７年９月３日　月曜日　午後２時３４分