Panasonic Memory Card Camera Recorder Ajhpx2700 Operating Instructions

							151Maintenance and Inspections: Maintenance
Maintenance and Inspections

						

							152Maintenance and Inspections: Maintenance REMOTE
Panasonic part number K1AY110JA001
1 CAM DATA (H) Data from the camera to the remote control (H)Maker part number HR10A-10R-10SC(71)
(Hirose Denki)
2 CAM DATA (C) Data from the camera to the remote control (C)
3 CAM CONT (H) Control signals from the remote control to the camera (H)
4 CAM CONT (C) Control signals from the remote control to the camera (C)
Connector at the cable side
5
RC-ONIdentification signals of the remote control
Low: ONMaker part number HR10A-10P-10P(73)
(Hirose Denki)
6 RC VIDEO OUT Video signals output to the remote control
7 RC VIDEO GND GND of the video signals to the remote control
8 NC Not used
9 UNREG 12 V DC +12 V power supply (AJ-RC10G: Max. 0.75 A)
10 GND GND
VFPanasonic part number K1AB120H0001
1 UNREG-12 V DC +12 V power supply (AJ-HVF21G: About 0.35 A)Maker part number HR12-14RA-20SC
(Hirose Denki)
2 UNREG-12 V DC +12 V power supply
3 A9.0 V DC +9 V power supply (not used)
4 VF-PB-GND GND for the viewfinder P
B signals
5 VF-PR-GND GND for the viewfinder P
R signals
6 VF-Y Viewfinder Y signals output
7 VF-Y-GND GND for the viewfinder Y signals
8 VF-CLK Serial data clock pulse signals
9 VF-WR Pulse signals for reading serial-parallel conversion data
10 VF-DATA Serial data signals for serial-parallel conversion
11 UNREG-GND GND
12 ZEBRA-SW On/off of the zebra signals
13 PEAKING Control of the peaking (not used)
14 SPARE Standby (not used)
15 VF-PR Viewfinder P
R signal output
16 VF-PB Viewfinder P
B signal output
17 MARKER-SW On/off of the marker (not used)
18 FRONT-VR FRONT AUDIO LEVEL adjustment (not used)
19 VR-GND GND for the FRONT AUDIO LEVEL (not used)
20 UNREG-GND GND

						

							153Maintenance and Inspections: Maintenance
Maintenance and Inspections
LENSPanasonic part number K1AY112JA001
1 RET-SW On/off of the return video
RETURN ON: GND
RETURN OFF: OPENMaker part number HR10A-10R-12SC(71)
(Hirose Denki)
2REC-START/
STOPControl for recording start/stop
3GND GND
4 IRIS-AUTO On/off of the forced iris servo
SERVO ON: +5 V±0.5 V
SERVO OFF: OPEN
5 IRIS-CONT Control output for the lens iris
F2.8: –6.2 V, F16: +3.4 V, CLOSE: +2.5 V
6 UNREG-12 V +12 V power supply for the lens (Max. 1.5 A)
7 IRIS-POSI Iris position signals
+3.4 V (F16) to +6.2 V (F2.8)
8 IRIS-G-MAX IRIS REMOTE/LOCAL (AUTO) signals
REMOTE: +5 V±0.5 V
LOCAL (AUTO): GND
9 EXT-POSI On/off of the built-in extender
EXTENDER ON: GND
EXTENDER OFF: OPEN
10 ZOOM-POSI Zoom position signals
11 FOCUS-POSI Focus position signal
12 SPARE Standby (not used)
GPSPanasonic part number K1AY106J0001
1 GPS TXA Transmission data from the GPS unit to the cameraMaker part number HR10A-7R-6SC(73)
(Hirose Denki)
2 GPS RXA Transmission data from the camera to the GPS unit
3 GPS VBAT Backup power supply connector for the GPS unit
(DC +3.3 V)
4 REC START SW Control signals of recording start/stop
5 GPS VCC Power supply connector for the GPS unit (DC +3.3 V)
6GPS GND GND
STARTSTOPSTART+5 V
0 V
1
2
4
5 6
3789
10
11
12
1
2
4 56
3
AJ-HPX2700G-VQT1V27_eng.book  153 ページ  ２００８年９月２日　火曜日　午後５時４３分 
						

							154Maintenance and Inspections: Maintenance Unislot Interface
Panasonic part number K1GB25A00010
1 CH-1 SHIELD GNDMaker part number HDBB-25S(05)
(Hirose Denki)
2 CH-1 HOT Audio input from the wireless receiver: CH1 HOT
3 CH-1 COLD Audio input from the wireless receiver: CH1 COLD
4GND GND
5 +12 V UNREG Power supply to the wireless receiver
6 RX ON Power supply remote output to the wireless receiver
7 RF WARN RF warning input from the wireless receiver
8 RM5 Not used
9 RM4 Not used
10 SPARE 1 Not used
11 SPARE 2 Not used
12 EXT CLK Not used
13 CLK SHIELD Not used
14 CH-2 SHIELD GND
15 CH-2 HOT Audio input from the wireless receiver: CH2 HOT
16 CH-2 COLD Audio input from the wireless receiver: CH2 COLD
17 +5.6 V Power supply to the wireless receiver
18 VIDEO OUT Not used
19 VIDEO RET Not used
20 VIDEO EN Not used
21 RM 1 (RM CLK) Not used
22 RM 2 (RM DATA) Not used
23 RM 3 (RM WR) Not used
24 RM +5 V Not used
25 RM GND Not used
13
1
14
25
AJ-HPX2700G-VQT1V27_eng.book  154 ページ  ２００８年９月２日　火曜日　午後５時４３分 
						

							155Maintenance and Inspections: Warning System
Maintenance and Inspections
If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the WARNING 
lamp, lamps inside the viewfinder and a warning tone.

						

							156Maintenance and Inspections: Warning System 6. Recording Error
Display window 
indication“00:00:00:11” appears in the time code 
display field. Even after recording is 
stopped, this display continues to blink 
until the next operation is performed.
WARNING lampBlinks 4 times per second while recording 
continues.
Tally lampBlinks 4 times per second while recording 
continues.
ViewfinderThe “REC WARNING” indicator lights up.
Warning toneBeeps 4 times per second while recording 
continues.
Warning descriptionThis indicates a failure either in the P2 
card recording or the recording circuit. 
This is displayed when attempting to 
record clips where the total quantity 
exceeds the upper limit (1000 pieces) for 
a single P2 card.
Recording/playback 
operationThe recording may stop or continue.
CountermeasuresConfirm the recording/playback operation 
after turning off the power supply once 
and then turning it on again.
If the recording cannot be performed 
normally, change the P2 card.
7. Low Wireless Signal Reception
Display window 
indicationNo display.
WARNING lampBlinks 4 times per second (during pause 
and recording).
Tally lampBlinks 4 times per second while recording 
continues.
ViewfinderThe “WIRELESS-RF” indicator lights up 
while recording continues.
Warning toneBeeps 4 times per second while recording 
continues.
Warning descriptionThis error indicates poor wireless audio 
reception conditions.
Recording/playback 
operationContinues to operate without receiving 
the wireless microphone signal.
CountermeasuresCheck the microphone power supply and 
the reception status of the wireless 
receiver.
8. 1394 Error
Display window 
indicationThe “1394 E-92” indicator in the display 
window blinks.
WARNING lampBlinks 4 times per second while recording 
continues.
Ta l l y  l a m pBlinks 4 times per second while recording 
continues.
Viewfinder“1394 INITIAL ERROR” indicator lights up 
(during pause and recording).
Warning toneBeeps 4 times per second while recording 
continues.
Warning descriptionThis indicates a failure of the DVCPRO 
connector.
Recording/playback 
operationSignals cannot be controlled or supplied 
to the device connected to the DVCPRO 
connector. However, recording and 
playback can be performed on the unit.
CountermeasuresCheck the connection between the 
IEEE1394 cable and the DVCPRO 
connector, settings of any external device 
and menus, and the turn on the power 
again.
If the warning indication is still 
illuminated, consult your distributor.
9. Battery Nearly Empty
Display window 
indicationOne of the bars in the battery remaining 
indicator starts blinking.
WARNING lampBlinks once per second.
Ta l l y  l a m pBlinks once per second.
ViewfinderThe “BATT” LED blinks.
Warning toneBeeps 4 times per second.
Warning descriptionThe battery is about to run out.
Recording/playback 
operationContinues to operate.
CountermeasuresReplace the battery as required.
10. P2 Card Nearly Full
Display window 
indicationOne of the bars for remaining MEDIA 
capacity starts blinking.
WARNING lampBlinks once per second while recording 
continues.
Ta l l y  l a m pBlinks once per second while recording 
continues.
ViewfinderThe P2 card remaining capacity indicator 
blinks.
Warning toneBeeps once per second while recording 
continues.
Warning descriptionThe total remaining capacity of all the P2 
cards is 2 minutes or less.
Recording/playback 
operationContinues to operate.
CountermeasuresReplace the cards. If there is an empty 
card slot, insert a new card.
AJ-HPX2700G-VQT1V27_eng.book  156 ページ  ２００８年９月２日　火曜日　午後５時４３分 
						

							157Maintenance and Inspections: Warning System
Maintenance and Inspections
11. P2 Card Error
Display window 
indicationIf the error occurs during recording, 
“00:00:00:11” appears in the time code 
display field. The indication continues to 
flash after recording is stopped and until 
the next operation is performed. There is 
no indication if the error occurs during 
playback.
WARNING lampIf the error occurs during recording, the 
lamp flashes 4 times per second for a 
period of about 3 seconds after recording 
stops. The lamp does not light if the error 
occurs during playback.
Ta l l y  l a m pIf the error occurs during recording, the 
lamp flashes 4 times per second for a 
period of about 3 seconds after recording 
stops. The lamp does not light if the error 
occurs during playback.
ViewfinderA flashing “CARD ERR 
						

							158Maintenance and Inspections: Warning System The following error codes are displayed in the display window if an error occurs in the camera:
Confirm the type of warning and refer to the details in the [Warning Description Tables] (page 155) for countermeasures.
Error Codes
Code No. Description Type of warnings
E-11 Video initialization error 1. System Errors
E-27 Recording control error 1. System Errors
E-30 P2 card removal error 2. Card removal error
E-34 LCD microcontroller error 1. System Errors
E-38 P2 streaming microcontroller error 1. System Errors
E-39 Abnormal initialization of the AVC-Intra codec 1. System Errors
E-3F Microprocessor error in the camera control circuit 1. System Errors
E-40 Image sequence error (in case of 24P, 30P and 25P), GENLOCK error 5. Image Sequence Error (24P, 30P, 25P)
E-63 Something is wrong with the system control microprocessor. 1. System Errors
E-6F Reference signal error. 1. System Errors
00:00:00:11 Recording error on a P2 card 6. Recording Error/11. P2 Card Error
Card Warning Code
Code No. Description RecordingIndication in display 
window
E-70The directory structure on the P2 card is not 
supported. ([DIR NG CARD (Slot No.)] is 
indicated on the viewfinder.)Operation continues. However, back up data 
on the P2 card as soon as possible, and 
format the card before using it again.A warning code blinks once 
every 2 seconds on the time 
code display section of the 
display window.
E-71The maximum number of overwrites on the P2 
card has been exceeded. ([RUN DOWN 
CARD (Slot No.)] is indicated on the 
viewfinder.)Operation continues. However, recording or 
playback may not operate correctly. It is 
recommended that you replace the P2 card 
with another one.
AJ-HPX2700G-VQT1V27_eng.book  158 ページ  ２００８年９月２日　火曜日　午後５時４３分 
						

							159Maintenance and Inspections: Warning System
Maintenance and Inspections
Warning and Error Display for Thumbnail Operation and USB HOST MODE
ItemMessageDescriptionMeasure
ThumbnailsCANNOT ACCESS! Data cannot be accessed because it is corrupted 
or for other reasons.Restore media and clips to normal state before 
access.
WRITE 
PROTECTED!The P2 or SD card is write protected. Insert write-enabled media.
CARD FULL! The P2 or SD card is full. Insert media with sufficient capacity.
NO CARD! No P2 or SD card is inserted. Insert compatible media.
NO FILE! The designated file is not found. Check the file.
CANNOT COPY! Images cannot be copied. Check the conditions for copying.
CANNOT DELETE ! Contents version mismatch prevents deletion. Match devices and contents version.
UNKNOWN 
CONTENTS 
FORMAT!Warning displayed to indicate contents version 
mismatch.Match devices and contents version.
CANNOT FORMAT! P2 card problem prevents formatting. Check P2 card.
CANNOT REPAIR! Data cannot be repaired since content that 
cannot be repaired is selected.Check selected content.
CANNOT RE-
CONNECT!A clip that does not span multiple P2 cards 
cannot be reconnected.Check selected content.
INVALID VALUE! Entered data was invalid. Enter data in a valid range.
UNKNOWN DATA! The metadata character code is invalid. Use UTF-8 for the metadata character code. Use 
the viewer to enter correct characters.
CANNOT REPAIR IN 
SELECTION!Some of the selected clip could not be repaired.
NO SD CARD! No SD card is inserted. Insert an SD card.
NO COPY TO SAME 
CARD!A clip cannot be copied to the card storing the 
original clip.Copy the selected clip to a card that does not 
contain the original clip.
SAME CLIP IS 
SELECTED!The clip cannot be copied because a clip that has 
already been copied and the original clip have 
been selected.Confirm the selected clip and release either the 
source clip or the destination clip and then 
execute the copy operation.
USER CLIP NAME 
MODIFIED!Characters in the clip name had to be deleted in 
adding the counter value.The user clip name plus the counter value can 
only contain up to 100 bytes. Characters in the 
clip name are automatically deleted when the 
total exceeds 100 bytes.
TOO MANY CLIPS! Too many clips are selected. Reduce the number of selected clips.
LACK OF REC 
CAPACITY!There is not enough recording capacity left on the 
card.Insert a card with sufficient recording capacity.
CANNOT CHANGE! Any thumbnails that cannot be produced on the 
AVC-Intra100 or AVC-Intra50 and displayed in 
gray cannot be changed at the text memo 
position.Set SYSTEM MODE according to the clips.
MISSING CLIP! A shot mark will be added to the clips recorded 
on multiple P2 cards when all P2 cards are not 
inserted yet.Insert all P2 cards with recorded clips, and 
confirm that the   incomplete clip indicators 
disappear, and then add shot marks.
Soft 
keyboardCANNOT CHANGE!  [PERSON] will be entered while the text memo is 
not available.Enter [TEXT] before entering [PERSON].
CANNOT SET!
I N VA L I D  VA L U E !The entered value is incorrect. Change the value.
AJ-HPX2700G-VQT1V27_eng.book  159 ページ  ２００８年９月２日　火曜日　午後５時４３分 
						

							160Maintenance and Inspections: Warning System
HDD
(USB HOST 
mode)HDD CAPACITY 
FULL!Not enough space left on the hard disk. There is not enough space on the connected 
hard disk. Use a new hard disk or formatted hard 
disk.
TOO MANY 
PA R T I T I O N S !There are too many partitions. Hard disks can handle up to 23 partitions. Use a 
new hard disk or formatted hard disk.
HDD 
DISCONNECTED!The unit is not connected to a hard disk. Reconnect the USB cable. If the hard disk does 
not operate normally, turn it off and turn it back on 
again.
CANNOT FORMAT! The hard disk cannot be initialized. Connect another hard disk drive.
TOO MANY 
TA R G E T S !Multiple devices are connected. Disconnect devices, turn off the unit and turn it 
back on again.
UNKNOWN DEVICE 
CONNECTED!The connected DVD drive is not compatible. Disconnect devices, turn off the unit and turn it 
back on again.
CANNOT ACCESS 
TA R G E T !An error occurred during hard disk access. Check hard disk status and connection.
CANNOT 
RECOGNIZE HDD!The destination target cannot be properly 
recognized.Reboot the hard disk or connect a different hard 
disk.
CANNOT ACCESS 
CARD!An error occurred during P2 card access. Check P2 card.
MISMATCH 
COMPONENT!Copying is not possible since the model number 
of the destination card does not match that of the 
source card.Use a P2 card with the same model number or 
import video in clip units.
P2 CARD IS 
UNFORMATTED!The P2 card is not formatted. Use a formatted P2 card.
CARD IS EMPTY! 
CANNOT COPY!The P2 card selected for copying is empty. Copying is not performed since the card is empty.
VERIFICATION 
FA IL E D !The compare check after copying failed. Copy the data again.
PLEASE FORMAT P2 
CARD!This warning indicates that data could not be 
imported from a hard disk to a P2 card because 
the P2 card contained recorded data.You cannot copy to a P2 card that contains data. 
Format the card on a P2 device and copy again.
ItemMessageDescriptionMeasure
AJ-HPX2700G-VQT1V27_eng.book  160 ページ  ２００８年９月２日　火曜日　午後５時４３分