Panasonic Memory Card Camera Recorder Ajhpx2000 Operating Instructions

							181Menu : Menu Description Tables
 Menu
‹Note
The frequency characteristics when the micro cut filter is applied are 
200 Hz to 10 kHz.
The ____ in the Adjustable Range column indicates the
preset mode. 
MIC/AUDIO1
Items/
Data Saved Adjustable 
RangeRemarks 
FRONT VR 
CH1OFF
FRONT
W. L .
REAR
ALL
Select whether or not to enable the 
FRONT AUDIO LEVEL control for the 
signal selected as the input signal to 
AUDIO CH1.
OFF:Disabled for any input selected.
Recording level does not change
by turning the volume control.
FRONT:Only enabled when FRONT is
selected. 
W. L . :Only enabled when WIRELESS
is selected. 
REAR:Only enabled when REAR is
selected. 
ALL:Enabled for any input selected. 
–CUF –
FRONT VR 
CH2OFF
FRONT
W. L .
REAR
ALL
Select whether or not to enable the 
FRONT AUDIO LEVEL control for the 
signal selected as an input signal to 
AUDIO CH2. 
OFF:Disabled for any input selected.
Recording level does not change
by turning the volume control.
FRONT:Only enabled when FRONT is
selected. 
W. L . :Only enabled when WIRELESS
is selected. 
REAR:Only enabled when REAR is
selected. 
ALL:Enabled for any input selected. 
–CUF –
MIC LOWCUT 
CH1OFF
FRONT
W. L .
REAR
Select the microphone low cut filter for 
Input Channel 1.
OFF:The microphone low cut filter is
disabled for any input.
FRONT:The microphone low cut filter is
enabled when the front
microphone is selected.
W. L . :The microphone low cut filter is
enabled only when the wireless
microphone is selected.
REAR:The microphone low cut filter is
enabled only when the rear
microphone is selected.
–CUF –
MIC LOWCUT 
CH2OFFFRONT
W. L .
REAR
Select the microphone low cut filter for 
Input Channel 2.
OFF:The microphone low cut filter is
disabled for any input.
FRONT:The microphone low cut filter is
enabled when the front
microphone is selected.
W. L . :The microphone low cut filter is
enabled only when the wireless
microphone is selected.
REAR:The microphone low cut filter is
enabled only when the rear
microphone is selected.
–CUF –
MIC LOWCUT 
CH3OFFFRONT
W. L .
REAR
Select the microphone low cut filter for 
Input Channel 3.
OFF:The microphone low cut filter is
disabled for any input.
FRONT:The microphone low cut filter is
enabled when the front
microphone is selected.
W. L . :The microphone low cut filter is
enabled only when the wireless
microphone is selected.
REAR:The microphone low cut filter is
enabled only when the rear
microphone is selected.
–CUF –
Items/
Data Saved Adjustable 
RangeRemarks 
MIC LOWCUT 
CH4OFF
FRONT
W. L .
REAR
Select the microphone low cut filter for 
Input Channel 4.
OFF:The microphone low cut filter is
disabled for any input.
FRONT:The microphone low cut filter is
enabled when the front
microphone is selected.
W. L . :The microphone low cut filter is
enabled only when the wireless
microphone is selected.
REAR:The microphone low cut filter is
enabled only when the rear
microphone is selected.
–CUF–
LIMITER CH1 ON
OFFSelect the limiter. 
The limiter is enabled when AUDIO 
SELECT CH1 switch is set to MAN.
–CUF–
LIMITER CH2 ON
OFFSelect the limiter. 
The limiter is enabled when AUDIO 
SELECT CH2 switch is set to MAN.
–CUF–
AUTO LEVEL 
CH3ONOFF
Select the level setting method.
For more information, see [CH3 and 
CH4 Recording Levels] (page 54)
–CUF–
AUTO LEVEL 
CH4ONOFF
Select the level setting method.
For more information, see [
CH3 and 
CH4 Recording Levels] (page 54)
–CUF–
25M REC CH 
SEL2CH
4CH
Select the audio channels to be 
recorded in the DVCPRO and DV 
for mats.
2CH:Only recorded in CH1 and CH2. 
4CH:Recorded in all channels from CH1 
to CH4. 
–CUF–
TEST TONE OFF
NORMAL
ALWAYS
CHSEL
Select the test signal. 
OFF:Disable test tone output. 
NORMAL:Test tone signals are output to
all of Channels 1 - 4 when the
OUTPUT/AUTO KNEE
selector switch has been
switched to BARS and CH1 of
the AUDIO IN switch has been
switched to FRONT.
ALWAYS:Test tone signals are always
output to all of Channels 1 - 4
when the OUTPUT/AUTO
KNEE selector switch has
been switched to BARS.
CHSEL:Output test tone to the
channels where the AUDIO IN
switch CH1 or CH2 is set to
FRONT when OUTPUT/AUTO
KNEE selector switch is set to
BARS. The test tone is not
output to CH3 and CH4.  –CUF–
AJ-HPX2000P(VQT1D27-1)E.book  181 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							182Menu : Menu Description Tables The ____ in the Adjustable Range column indicates the
preset mode. 
MIC/AUDIO2
Items/
Data Saved Adjustable 
RangeRemarks 
FRONT MIC 
POWERON
OFF
Select the phantom power supply for the 
front microphone. 
–CUF–
REAR MIC 
POWERONOFF
Select the phantom power supply for the 
rear microphone. 
When OFF is selected, no phantom 
power is supplied even if the REAR 
AUDIO CH1 or CH2 switch is set to +48.
–CUF–
MONITOR 
SELECTSTEREOMIX
When the MONITOR switch is set to ST 
(stereo), select the signal format for the 
monitor output. 
–CUF–
FRONT MIC 
LEVEL–40dB–50dB
Select the front microphone input level. 
–CUF–
REAR MIC 
CH1 LVL–50dB
–60dBSelect the rear microphone input level. 
–CUF–
REAR MIC 
CH2 LVL–50dB
–60dBSelect the rear microphone input level. 
–CUF–
REAR LINE IN 
LV L0dB
+4dB
–3dB
Select the rear line input level. 
–CUF–
AU DI O O U T 
LV L0dB
+4dB
–3dB
Select the audio output level. 
–CUF–
HEADROOM 18dB
20dBSet the headroom (standard level). 
–CUF–
WIRELESS 
WA RNON
OFFSelect whether or not to enable the 
alarm to trigger for poor wireless 
receiver reception. 
–CUF–
TC/UB
Items/
Data Saved Adjustable 
RangeRemarks 
TC MODEDF
NDF
Set the time code mode. DF:Drop frame. 
NDF:Non drop frame. 
‹Note
When the camera-recorder operates at 
50 Hz or in 24P or 24PA mode, the non-
drop frame is always used.
–CUF–
UB MODEUSERTIME
DATE
EXT
TCG
FRM RATE
REGEN
Select the user bits mode. 
USER:Select UB value set in the LCD
section. 
TIME:Select local time (hours,
minutes, seconds). 
DATE:Select local date and time (2 last
digits of year, month, date, time). 
EXT:When CAM , VIDEO, or
SDI is selected in REC
SIGNAL on the SYSTEM MODE
screen, the user bits input to the
TC IN connector are recorded. 
When 1394 is selected, the
user bits of signals input to the
DVCPRO/DV connector are
recorded.
If reading fails, USER value is
retained.
TCG:TCG value enters UB. 
FRM RATE:
Select the shooting information (e.g. 
frame rate) for the camera. For more 
information, see [
Frame rate 
information recorded in user bits] 
(page 58).
When clips recorded in Native mode 
are played back, the frame rate 
information recorded in users bits in 
the VAUX range is output.
REGEN:Read out value stored in the
card and record value
continuously. 
‹NoteWhen the camera-recorder is in 720P 
mode, FRM RATE is always selected.
–CUF–
AJ-HPX2000P(VQT1D27-1)E.book  182 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							183Menu : Menu Description Tables
 Menu
‹Note
Please refer to [Setting UMID Information] (page 67) for the
UMID information setting. 
The ____ in the Adjustable Range column indicates the
preset mode. 
Items/
Data Saved Adjustable 
RangeRemarks 
VITC UB 
MODEUSER/EXT
TIME
DATE
TCG
FRM RATE
REGEN
Select the user bits mode for VAUX TC 
(VITC). 
USER/EXT:
If UB MODE is set to EXT, the EXT 
value is recorded. If not, USER value 
set by UB is recorded. 
TIME:Select local time (hours,
minutes, seconds). 
DATE:Select local date and time (2 last
digits of year, month, date, time). 
TCG:TCG value enters UB. 
FRM RATE:
Select camera shoting information 
(frame rate, etc.). For more 
information, see [
Frame rate 
information recorded in user bits] 
(page 58).
REGEN:Read out value stored in card
and record value continuously. 
‹Note
When the unit operates in 24P, 24PA, 
720P, and Native mode, the FRM RATE is 
fixed.
–CUF –
TCG SET 
HOLDON
OFFON/OFF switching for the feature that 
always starts recording (when the power 
is turned ON again) the TCG value that 
was set before the power is turned OFF. 
–CUF –
FIRST REC 
TCPRESET
REGENFor the first recording after the power is 
turned on, a P2 card is inserted and 
then switching from this P2 card to 
another recording-target P2 card is 
performed, select whether or not to 
regenerate the time code as the value 
on the new P2 card.
PRESET:
Use the camera-recorder’s internal 
time code. 
REGEN:
For clips recorded on the recording-
target P2 card, regenerate the time 
code as the time code of the clip that 
has the most recent date and time. 
‹Notes
z
Set the date and time accurately. For
guidance on setting, see [Setting the
Internal Clock’s Date and Time] (page
60).
zDuring operation in either 24P or
24PA mode, regeneration of the value
of the card recorded in drop-frame is
not permitted.
–CUF –
P. O F F  L C D  
DISPLAYONOFF
Select whether or not to display the time 
code setting and counter indication on 
the LCD monitor when the power is 
turned OFF. 
ON:Display setting and indication while 
the power is turned OFF. 
OFF:Power-down LCD monitor while 
camera power is turned OFF. 
Setting and indication disabled. 
–CUF –
TC OUTTCG
TCG/TCR
Select the time code to be output to the 
time code output connector. 
TCG:Always output time code generator 
value. 
TCG/TCR:
Display time code generator value 
in recording mode, and time code 
reader value in playback mode. 
–CUF –
Items/
Data Saved Adjustable 
RangeRemarks 
TC DISP SEL30F24F
Select the display format for the time 
code frame digits. (For 1080-59.94i, 
720-59.94P or 480-59.94i only
£
For details, refer to [Recording time code 
and user bits] (page 56).
30F:Display time code frame digits in 30 
frames. 
24F:Convert time code frame digits into 
24 frames for display. 
–CUF–
TC VIDEO 
SYNCRO0
1
2
3
For setting to correct the time code 
according to the delay of video signals.
0:
Do not correct.1:To delay the time code to be input 
according to the timing of the video 
images.
2:To forward the time code to be output 
according to the timing of the video 
images.
3:To delay the time code to be input and 
forward the time code to be output, 
respectively, according to the timing of 
the video images.
For details, refer to [Externally Locking 
the Time Code] (page 62).
–CUF–
REC REVIEW 
REGENON
OFFFor selecting whether the time code is 
regenerated to the value on the P2 card 
or not, when subsequent recording 
starts after setting the RET SW item on 
the SW MODE screen to R.REVIEW 
and pressing the RET button on the lens 
or the USER button on the unit on which 
the RET SW function is assigned.
ON:The time code is regenerated to 
the value on the tape.
OFF:The time code is not regenerated.
–CUF–
UMID SET/INFO
Items/
Data Saved Adjustable 
RangeRemarks 
COUNTRYNO-INFOInput the user’s country. NO-INFO is 
displayed until the input completes. 
–CUF–
ORGANIZATIONNO-INFOInput the user’s organisation or 
company name. NO-INFO is displayed 
until the input completes. 
–CUF–
USERNO-INFOInput the user name. NO-INFO is 
displayed until the input completes. 
–CUF–
DEVICE 
NODEIndicate the product ID number. 
–––––
AJ-HPX2000P(VQT1D27-1)E.book  183 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							184Menu : Menu Description Tables
‹Note
For a USB DEVICE mode, errors occur even if the
respective items for SD CARD READ/WRITE are
executed, since it does not access an SD memory card.
Set PC MODE to “OFF” and then execute the operation
again.
The ____ in the Adjustable Range column indicates the
preset mode. 
FILE
SD CARD READ/WRITE
Items/
Data Saved Adjustable 
RangeRemarks 
R.SELECT1
 : 
8
Select the file number to read out. 
–––F–
READRead out the data from the SD memory 
card. 
–––––
W. S E L E C T1 : 
8
Select the file number to write in. 
–––F–
WRITEWrite the camera-recorder’s menu data 
to the SD memory card.
–––––
CARD 
CONFIGFormat the SD memory card. 
–––––
TITLE READRead out the title of the data recorded 
on the SD memory card. 
–––––
TITLE1 - 8¢¢¢¢
¢¢¢¢Up to 8 letters can be set for the title 
name. 
–––––
SD CARD R/W SELECT
Items/
Data Saved Adjustable 
RangeRemarks 
SYSTEM 
MODE R/WON
OFFSpecify whether or not to use the 
settings for the options on the SYSTEM 
MODE screen when data is read or 
written from or to SD memory cards.
–––F–
ID READ/
WRITEON
OFFSelect whether or not to include the 
CAMERA ID when reading out or writing 
to the SD memory card. 
–––F–
USER MENU 
SELECT R/WON
OFF
Select whether or not to include the 
FILE MENU SELECT settings when 
reading out or writing to the SD memory 
card. 
–––F–
SYSTEM 
MENU R/WONOFF
Specify whether or not to use the 
settings on all screens except the 
SYSTEM MODE screen on the 
SYSTEM SETTING page and the 
settings on the OPTION MENU page 
when data is read or written from or to 
SD memory cards.
–––F–
PAINT MENU 
LEVEL R/WONOFF
Select whether or not to include the 
adjusted values on the PAINT page 
when reading out or writing to the SD 
memory card. 
–––F–
PAINT MENU 
SW(
„) R/WONOFF
Select whether or not to include the set 
values on the PAINT MENU page when 
reading out or writing to the SD memory 
card. 
–––F–
VF MENU 
R/WONOFF
Select whether or not to include the set 
values on the VF page when reading out 
or writing to the SD memory card. 
–––F–
CAM OPE 
MENU R/WON
OFF
Select whether or not to include the set 
values on the CAM OPERATION page 
when reading out or writing to the SD 
memory card. 
–––F–
MAIN OPE 
MENU R/WONOFF
Select whether or not to include the set 
values on the MAIN OPERATION page 
when reading out or writing to the SD 
memory card. 
–––F–
MAINTE 
MENU R/WONOFF
Select whether or not to include the set 
values on the MAINTENANCE page 
when reading out or writing to the SD 
memory card. 
–––F–
AJ-HPX2000P(VQT1D27-1)E.book  184 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							185Menu : Menu Description Tables
 Menu
‹Note
For a USB DEVICE mode, errors occur even if the
respective items of LENS FILE CARD R/W are executed,
since it does not access an SD memory card. Set PC
MODE to “OFF” and then execute the operation again.
‹Note
For a USB DEVICE mode, errors occur even if the READ
USER DATA item is executed, since it does not access an
SD memory card. Set PC MODE to “OFF” and then
execute the operation again.
‹Note
For a USB DEVICE mode, errors occur even if the READ
FACTORY DATA item is executed, since it does not access
an SD memory card. Set PC MODE to “OFF” and then
execute the operation again.
The ____ in the Adjustable Range column indicates the
preset mode. 
LENS FILE
Items/
Data Saved Adjustable 
RangeRemarks 
FILE NO.1
 : 
8
Select the lens file number. 
–––F–
READRead the lens file data. 
–––––
WRITEWrite the lens file data. 
–––––
RESET ALLFor resetting the all data of the lens file.
–––––
TITLE1 - 8¢¢¢¢¢¢¢
¢¢¢¢¢Up to 12 letters can be set for the title 
name. 
–––––
LENS FILE CARD R/W
Items/
Data Saved Adjustable 
RangeRemarks 
CARD FILE 
SELECT1
 : 
8
For selecting the number of the lens file 
in the SD memory card.
–––F–
READFor reading the lens file data from the 
SD memory card.
–––––
WRITEFor writing the lens file data into the SD 
memory card.
–––––
TITLE READFor reading the title of the lens file in the 
SD memory card.
–––––
TITLE1 - 8¢¢¢¢¢¢¢
¢¢¢¢¢For setting a title consisting of not more 
than 12 characters.
–––––
SCENE
Items/
Data Saved Adjustable 
RangeRemarks 
READ USER 
DATARead out the data from the user area in 
the memory. 
–––––
SCENE SEL1 : 
4
Select the scene file. 
–––F–
READRead the scene file. 
–––––
WRITEWrite the scene file. 
–––––
RESETReset the scene file values to the initial 
values. 
–––––
TITLE 1-4Create the scene file title. 
–––––
INITIALIZE
Items/
Data Saved Adjustable 
RangeRemarks 
READ 
FA C TO RY  
DATAThe menu (MAIN MENU, OPTION 
MENU) values are all reset to factory 
settings. 
‹NoteThe settings for the following are not 
reset to the factory-set values.
zScene filezUser data
zLens filezBlack shading data
–––––
WRITE USER 
DATASave the user preference menu data in 
the camera’s internal memory. 
–––––
AJ-HPX2000P(VQT1D27-1)E.book  185 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							186Menu : Menu Description Tables
zData adjusted on the LENS FILE ADJ screen can be
stored on an SD memory card as a lens file.
The ____ in the Adjustable Range column indicates the
preset mode. 
MAINTENANCE
SYSTEM CHECK
Items/
Data Saved Adjustable 
RangeRemarks 
COLOR 
CHECKON
OFFON/OFF switching for checking proper 
operation of the camera-recorder. 
The RGB level in the area around the 
center of the screen is indicated in the 
viewfinder to show whether each signal 
is successfully communicated from the 
optical channel to the digital channel 
and processed.
–––––
LENS ADJ
Items/
Data Saved Adjustable 
RangeRemarks 
F2.8 ADJ ON
OFFThe iris is only set to F2.8 when this item 
set to ON. (Adjustment to F2.8 will be 
executed on the lens)
–––––
F16 ADJ ON
OFFThe iris is only set to F16 when this item 
set to ON. (Adjustment to F16 will be 
executed on the lens
£–––––
BLACK SHADING
Items/
Data Saved Adjustable 
RangeRemarks 
CORRECTON
OFF
ON/OFF switching for digital black 
shading compensation. 
–CUFR
DETECTION
(DIG)–Execute digital black shading 
compensation. 
–––––
WHITE SHADING
Items/
Data Saved Adjustable 
RangeRemarks 
CORRECTON
OFF
ON/OFF switching for white shading 
compensation. 
–CUFR
R H SAW
R H PARA
R V SAW
R V PARA
G H SAW
G H PARA
G V SAW
G V PARA
B H SAW
B H PARA
B V SAW
B V PARA–255 : +000 : +255
For executing the white shading 
compensation manually.
The sawteeth-shaped waveform and the 
parabola waveform of the respective 
RGB channels are adjusted in the 
horizontal direction and the vertical 
direction.
–––F–
LENS FILE ADJ
Items/
Data Saved Adjustable 
RangeRemarks 
RB GAIN 
CTRL RESETON
OFF
ON:The gains of Rch and Bch 
adjusted in  screen are reset.
Furthermore, the flare levels of 
Rch, Gch and Bch that are 
adjusted on  screen are reset.
OFF:The gains of Rch and Bch 
adjusted in  screen areenabled.
Furthermore, the flare levels of 
Rch, Gch and Bch that are 
adjusted on  screen are enabled.
–––F–
LENS R GAIN 
OFFSET–200 : +000 : +200
For compensating Rch sensitivity of the 
lens used.
–––F–
LENS B GAIN 
OFFSET–200 : +000 : +200
For compensating Bch sensitivity of the 
lens used.
–––F–
LENS R 
FLARE000 : 100
For adjusting the flare level of Rch.
–––F–
LENS G 
FLARE000 : 100
For adjusting the flare level of Gch.
–––F–
LENS B 
FLARE000 : 100
For adjusting the flare level of Bch.
–––F–
AJ-HPX2000P(VQT1D27-1)E.book  186 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							187Menu : Menu Description Tables
 Menu
DIAGNOSTIC1
Items/
Data Saved Adjustable 
RangeRemarks 
CAMSOFT 
MAINDisplays the version of the main 
software for the camera microprocessor.
–––––
CAM TABLEDisplay the table version. 
–––––
PULSE FPGADisplays the version of the program for 
driving the CCD.
–––––
UCIF FPGADisplays the version of the program for 
the microprocessor interface FPGA.
–––––
FM FPGADisplays the version of the program for 
the frame memory control FPGA.
–––––
CHAR FPGADisplays the version of the program for 
the HD signal I/O control FPGA.
–––––
DC FPGADisplays the version of the program for 
the SD signal I/O control FPGA.
–––––
DIAGNOSTIC2
Items/
Data Saved Adjustable 
RangeRemarks 
SYSCON 
SOFTDisplay the software version for the 
system control microprocessor. 
–––––
LCD SOFTDisplay the software version for the LCD 
microprocessor.
–––––
P2CS OSDisplay the OS version for the streaming 
controller. 
–––––
P2CS APDisplay the application version for the 
streaming controller. 
–––––
SH4CTRL 
FPGADisplay the program version for the 
streaming control FPGA. 
–––––
PRCCTRL 
FPGADisplays the version of the program for 
the prerecording control FPGA.
–––––
SYSIF FPGADisplay the program version for the 
serial interface FPGA. 
–––––
SDI IN FPGADisplays the version of the program for 
the SDI board FPGA (optional).
–––––
AV C - I  S O F TDisplay the control software version of the 
AVC-I board (optional).
–––––
AV C - I  F P G ADisplay the FPGA program version of the 
AVC-I board (optional).
–––––
HOURS METER
Items/
Data Saved Adjustable 
RangeRemarks 
OPERATIONDisplay total hours the camera power 
has been turned ON. 
–––––
P. O N  T I M E SDisplay total number of times the power 
switch has been turned ON. 
–––––
AJ-HPX2000P(VQT1D27-1)E.book  187 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							188Menu : Menu Description Tables The ____ in the Adjustable Range column indicates the
preset mode. 
OPTION MENU
OPTION
Items/
Data Saved Adjustable 
RangeRemarks 
ENG 
SECURITYON
OFFSelect whether or not to prohibit opening 
the menu screen. 
ON:Menu screen cannot be opened. 
Please consult your distributor to 
release the setting. 
OFF:Menu screen can be opened. 
–––––
FRAME RATE 
UBFRM RATEMENU
For setting the user bits to record when 
the video system is set to 24P or 24PA, 
or when the recording format is set to 
720P. For details, refer to [
Recording 
time code and user bits
] (page 56).
FRM RATE:
For recording the shooting information 
(frame rate etc.) of the camera.
MENU:This follows the settings in the
UB MODE item and the VITC
UB MODE item of 
screen. 
However, the camera
recording information is always
recorded when recording in
Native mode.
–C– – –
1394 CONFIGDFLT(000)001 : 255
This is the menu for expanding the 
DVCPRO/DV connector.
Use with DFLT in normal operation.
–C– – –
1394 GAP 
COUNT0 : 40 : 63
For setting the interval between packets.
–C– – –
AU DI O O U T 
DELAYDELAYED
THROUGHSelect whether or not to delay audio, 
headphone and speaker outputs. 
DELAYED:
Delay audio output in synchronisation 
with video output. 
THROUGH:Output audio input without delay. This 
setting prevents echo effect between 
the sound source and audio output 
when the sound source is near the 
camera-recorder. 
–C– – –
FAN MODE OFF
AU TOFor setting the operation mode of the fan
OFF:The fan always stops.
AU TO:The fan will run automatically 
when the temperature in the unit 
increases.
‹Note
Once the power is turned off, this will 
always be set to AUTO whenever the 
power is turned on. If the unit is 
operated as the fan stops, the 
temperature in the unit will increase, and 
data may not record or play back 
properly. Use the unit after setting this 
item to AUTO for normal operation.
–––––
AJ-HPX2000P(VQT1D27-1)E.book  188 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							189Updating the firmware incorporated into the camera-recorder
 Updating the firmware incorporated into the camera-recorder
For the most up-to-date information on firmware, see the support page for P2 at the following Web site:
https://eww.pavc.panasonic.co.jp/pro-av/
To update the firmware, confirm the version on AJ-HPX2000 by selecting MAINTENANCE 
> DIAGNOSTIC 1 and 
DIAGNOSTIC 2 screens from the menu, and then access the above Web site to download the firmware if necessary. 
Then, load the downloaded file on AJ-HPX2000 through an SD memory card to complete the update. For more 
information on how to update the firmware, see the above site.
‹Note
SD cards used on AJ-HPX2000 must be compliant with the SD standards. In addition, they must be formatted with the 
camera-recorder. If they must be formatted with a PC, then download special software from the above Web site and use it 
to format the SD cards.
An SDHC memory card cannot be used for updating.
Updating the firmware incorporated 
into the camera-recorder
AJ-HPX2000P(VQT1D27-1)E.book  189 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							190Specifications
General
Operating temperature:
0 °C to +40 °C (32 °F to +104 °F)
Storage temperature: 
–20 °C to +60 °C (–4 °F to +140 °F)Operating humidity: 
10% to maximum 85% (relative 
humidity)
Maximum continuous operation: 
Approximately 120 minutes (using an 
Anton/Bauer DIONIC90 battery)
Dimensions (W a H a D): 
137 mm a 209 mm a 318 mm
(5-3/16 inches a 8-1/2 inches a 12-1/2 
inches)
(excluding handle and wireless option 
cover)
Weight:  Approx. 4.5 kg (9.9 lb)
 (main unit only, excluding VF mount)
Pickup devices:  2/3-inch CCD a 3
Image pickup scheme:
RGB 3CCD
Total pixels: 1370 (H) a 744 (V)
Valid pixels: 1280 (H) a 720 (V)
Filter: 1: 3200K
2: 5600K + 1/8ND
3: 5600K
4: 5600K + 1/64ND
Quantizing: 14-bit
Horizontal drive frequency: 
74.1758 MHz (59.94 Hz)
74.25 MHz (50 Hz)
Sampling frequencies:
74.1758 MHz (59.94 Hz)
74.25 MHz (50 Hz)
Digital signal processing: 
74.1758 MHz (59.94 Hz)
74.25 MHz (50 Hz)
Programmable gain: 
–3 dB, 0 dB, +3 dB, +6 dB, +9, dB 
+12 dB, +15 dB, +18 dB, +21 dB, 
+24 dB, +27 dB or +30 dB
Digital Super Gain (DS.GAIN): 
Selectable from +6 dB, +10 dB, +12 dB, 
+15 dB or +20 dB
LINE MIX GAIN:
+6 dB (selectable between on and off)
Super Gain (S.GAIN): 
Selectable from 30 dB, 36 dB, 42 dB or 
48 dBShutter speeds:  1/60 (50 Hz), 1/100 (59.94 Hz), 1/120, 
1/250, 1/500, 1/1000, 1/2000, HALF
Synchro-scan shutter: 
1/60.3 to 1/249.8
(1080-59.94i/720-59.94P/480-59.94i)
1/30.2 to 1/249.8
(1080-29.97P/720-29.97P/480-29.97P)
1/24.1 to 1/249.8
(1080-23.98P(A)/720-23.98P/480-
23.98P(A))
1/50.2 to 1/209.5
(1080-50i/720-50P/576-50i)
1/25.2 to 1/209.5
(1080-25P/720-25P/576-25P)
Lens mount:  2/3-inch bayonet type
Color separation optical system: 
Optical prism (F1.4)
Sensitivity:  F10 (2000 lx, 89.9% reflection)
Minimum object illuminance: 
0.007 lx
(For F1.4, +48 dB (S. GAIN), +20 dB 
(DS. GAIN), +6 dB (LINE MIX GAIN))
Video S/N:  54 dB (standard)
Registration error: 0.03% or less (all areas, excluding lens 
distortion)
Power supply:
DC 12 V (11.0 V - 17.0 V)
Power consumption:
36 W (Main unit only, with LCD monitor OFF)
43 W (With the SDI-IN and AVC-Intra option installed, 
LCD monitor ON)
indicates safety information. 
Camera Unit
Specifications
AJ-HPX2000P(VQT1D27-1)E.book  190 ページ  ２００７年７月３０日　月曜日　午後１時３１分