Panasonic Memory Card Camera Recorder Ajhpx2000 Operating Instructions

							141Maintenance and Inspections : Maintenance
 Maintenance and Inspections
‹Note
Ensure that the polarities are used correctly for a power
supply from an external source.
Connector Signals
DC IN
1GND
2NC
3NC
4 +12V
FRONT MIC IN
1GND
2 L CH IN (H)
3 L CH IN (C)
4 R CH IN (H)
5 R CH IN (C)
AUD I O I N
1GND
2 AUDIO IN(H)
3 AUDIO IN(C)
AUDIO OUT
1GND
2L CH OUT (H)
3L CH OUT (C)
4 R CH OUT (H)
5 R CH OUT (C)
12
34
Matsushita part number K1AA104H0038
Maker part number HA16RX-4P
¢SW1£
(Hirose Denki)
PUSH
1 5
2
3 4
Matsushita part number K1AB105B0002
Maker part number NC5FBH
(NEUTRIK)
PUSH
1
3 2
Matsushita part number K1AB103A0011
Maker part number HA16PRM-3SG
(Hirose Denki)
5
4
3 2 1
Matsushita part number K1AA105H0016
Maker part number HA16RD-5P(76)
(Hirose Denki)
DC OUT
1GND
2R TALLY
(Open collector)
3 REC START SW
4+12V OUT
(Max. 1.5 A)
1
2 3 4
Matsushita part number K1AY104J0001
Maker part number HR10A-7R-4SC(73)
(Hirose Denki)
Connector at the cable side
Maker part number HR10A-7R-4P(73)
(Hirose Denki)
AJ-HPX2000P(VQT1D27-1)E.book  141 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							142Maintenance and Inspections : Maintenance REMOTE
1 CAM DATA (H) Data from the camera to the remote control (H)
2 CAM DATA (C) Data from the camera to the remote control (C)
3 CAM CONT (H) Control signals from the remote control to the camera (H)
4 CAM CONT (C) Control signals from the remote control to the camera (C)
5 RC-ON Identification signals of the remote control
Low: ON
6 RC VIDEO OUT Video signals output to the remote control
7 RC VIDEO GND GND of the video signals to the remote control
8 NC Not used
9 UNREG 12V DC +12 V power supply (AJ-RC10G: Max. 0.75 A)
10 GND GND
VF
1 UNREG-12V DC +12 V power supply (AJ-HVF21G: About 0.35 A)
2 UNREG-12V DC +12 V power supply
3 A9.0V DC +9 V power supply (not used)
4 VF-PB-GND GND for the viewfinder P
B signals
5 VF-PR-GND GND for the viewfinder P
R signals
6 VF-Y Viewfinder Y signals output
7 VF-Y-GND GND for the viewfinder Y signals
8 VF-CLK Serial data clock pulse signals
9 VF-WR Pulse signals for reading serial-parallel conversion data
10 VF-DATA Serial data signals for serial-parallel conversion
11 UNREG-GND GND
12 ZEBRA-SW ON/OFF of the zebra signals
13 PEAKING Control of the peaking (not used)
14 SPARE Standby (not used)
15 VF-PR Viewfinder P
R signal output
16 VF-PB Viewfinder P
B signal output
17 MARKER-SW ON/OFF of the marker (not used)
18 FRONT-VR FRONT AUDIO LEVEL adjustment (not used)
19 VR-GND GND for the FRONT AUDIO LEVEL (not used)
20 UNREG-GND GND
‹Caution
Total amount of current from the respective connectors for DC OUT, REMOTE,
VF, and LENS should not exceed 2.5 A.
1
2
4
5 6 78
9 10
3
Matsushita part number K1AY110JA001
Maker part number HR10A-10R-10SC(71)
(Hirose Denki)
Connector at the cable side
Maker part number HR10A-10P-10P(73)
(Hirose Denki)
12
3
45
6
789
10
11
12
1314 15
16
17
1819 20
Matsushita part number K1AB120H0001
Maker part number HR12-14RA-20SC
(Hirose Denki)
AJ-HPX2000P(VQT1D27-1)E.book  142 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							143Maintenance and Inspections : Maintenance
 Maintenance and Inspections
LENS
1 RET-SW ON/OFF of the return video
RETURN ON: GND
RETURN OFF: OPEN
2 REC-START/STOP Control for recording start/stop
3GND GND
4 IRIS-AUTO ON/OFF of the forced iris servo
SERVO ON: +5V±0.5V
SERVO OFF: OPEN
5 IRIS-CONT Control output for the lens iris
F2.8: –6.2 V, F16: +3.4 V, CLOSE: +2.5 V
6 UNREG-12V +12V power supply for the lens (Max. 1.5 A)
7 IRIS-POSI Iris position signals
3.4 V (F16) to +6.2 V (F2.8)
8 IRIS-G-MAX IRIS REMOTE/LOCAL (AUTO) signals
REMOTE: +5V±0.5V
LOCAL (AUTO):GND
9 EXT-POSI ON/OFF of the built-in extender
EXTENDER ON: GND
EXTENDER OFF: OPEN
10 ZOOM-POSI Zoom position signals
11 FOCUS-POSI Focus position signal
12 SPARE Standby (not used)
1
2
4
5 6
3 789
10
11
12
Matsushita part number K1AY112JA001
Maker part number HR10A-10R-12SC(71)
(Hirose Denki)
STARTSTOPSTART+5 V
0 V
GPS
1 GPS TXA Transmission data from the GPS unit to the camera
2 GPS RXA Transmission data from the camera to the GPS unit
3 GPS VBAT Backup power supply connector for the GPS unit
(DC+3.3 V)
4 REC START SW Control signals of REC start/stop
5 GPS VCC Power supply connector for the GPS unit (DC+3.3 V)
6GPS GND GND
1
2
4 56
3
Matsushita part number K1AY106J0001
Maker part number HR10A-7R-6SC(73)
(Hirose Denki)
AJ-HPX2000P(VQT1D27-1)E.book  143 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							144Maintenance and Inspections : Maintenance Unislot Interface
1 CH-1 SHIELD GND
2 CH-1 HOT Audio input from the wireless receiver: HOT
3 CH-1 COLD Audio input from the wireless receiver: COLD
4GND GND
5 +12V UNREG Power supply to the wireless receiver
6 RX ON Power supply remote output to the wireless receiver
7 RF WARN RF warning input from the wireless receiver
8RM5 Not used
9RM4 Not used
10 SPARE 1 Not used
11 SPARE 2 Not used
12 EXT CLK Not used
13 CLK SHIELD Not used
14 CH-2 SHIELD Not used
15 CH-2 HOT Not used
16 CH-2 COLD Not used
17 +5.6V Power supply to the wireless receiver
18 VIDEO OUT Not used
19 VIDEO RET Not used
20 VIDEO EN Not used
21 RM 1 (RM CLK) Not used
22 RM 2 (RM DATA) Not used
23 RM 3 (RM WR) Not used
24 RM +5V Not used
25 RM GND Not used
13
1
14
25
Matsushita part number K1GB25A00010
Maker part number HDBB-25S(05)
(Hirose Denki)
AJ-HPX2000P(VQT1D27-1)E.book  144 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							145Maintenance and Inspections : Warning System
 Maintenance and Inspections
If a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the 
WARNING lamp, lamps inside the viewfinder and a warning tone. 
‹Note
The WARNING lamp has the highest priority, followed by the tally lamp, and then the warning tone. When multiple errors 
occur simultaneously a higher priority indication will be triggered. The [WIRELESS RF], however, may not be indicated, 
depending on the menu setting. 
Warning System
Warning Description Tables
1. System Errors
Display window 
indication The error code lights up.
WARNING lamp Blinks 4 times per second. 
Tally lampBlinks 4 times per second. 
ViewfinderThe SYSTEM ERROR indication and the 
error code light up. 
Warning toneBeeps continuously. 
Warning 
description An error in the reference signal or the 
communication. 
Recording/
playback 
operation The operation stops. 
CountermeasuresPlease confirm  [Error Codes] (page 148) 
and consult your distributor.
3. Battery Empty
Display window 
indication All 7 bar indicators for battery remaining 
capacity start blinking. 
WARNING lamp Lights up. 
Tally lampBlinks once per second. 
ViewfinderThe BATT LED lights up. 
Warning toneBeeps continuously. 
Warning 
description The battery has run out. 
Recording/
playback 
operation The operation stops. 
CountermeasuresReplace the battery. 
2. Card removal error
Display window 
indication Error code E-30 blinks.
WARNING lamp Blinks 4 times per second.
Tally lampBlinks 4 times per second.
ViewfinderThe “TURN POWER OFF” indicator lights 
up.
Warning toneContinues to beep.
Warning 
description The P2 card being accessed has been 
removed, resulting in an error in the internal 
memory of the camera-recorder.
Recording/
playback 
operation Cannot be performed.
CountermeasuresTurn off the power to the camera-recorder. If 
there is an error in a clip on the removed P2 
card, repair the clip.
4. Write-protect
Display window 
indication All 7 bar indicators for remaining MEDIA 
capacity start blinking. 
WARNING lamp This lamp will illuminate continuously until an 
operation is made after recording.
Tally lampThis lamp will flash 4 times every second 
until an operation is made after recording.
ViewfinderThe WP indicator  lights up. 
Warning toneThis tone will sound continuously until an 
operation is made after recording.
Warning 
description The inserted P2 cards are write-protected. 
Recording/
playback 
operation Recording is disabled. 
CountermeasuresDisable the write-protect or replace the P2 
card. 
AJ-HPX2000P(VQT1D27-1)E.book  145 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							146Maintenance and Inspections : Warning System 5. P2 Card Fully Recorded
Display window 
indication All 7 bar indicators for remaining MEDIA 
capacity start blinking. 
WARNING lamp This lamp will illuminate continuously until an 
operation is made after recording.
Tally lampThis lamp will flash 4 times every second 
until an operation is made after recording.
ViewfinderThe END indicator blinks. 
Warning toneThis tone will sound continuously until an 
operation is made after recording.
Warning 
description The P2 cards are recorded to maximum 
capacity. 
Recording/
playback 
operation The recording stops. 
CountermeasuresDelete the clips in the P2 card or insert a 
new P2 card. 
7. Recording Error
Display window 
indication “00:00:00:11” appears in the time code 
display field. Even after recording is stopped, 
this display continues to blink until the next 
operation is performed.
WARNING lamp Blinks 4 times per second while recording 
continues. 
Tally lampBlinks 4 times per second while recording 
continues. 
ViewfinderThe REC WARNING indicator lights up. 
Warning toneBeeps 4 times per second while recording 
continues. 
Warning 
description This indicates a failure either in the P2 card 
recording or the recording circuit. 
This is 
displayed when attempting to record clips 
where the total quantity exceeds the upper 
limit (1000 pieces) for a single P2 card.
Recording/
playback 
operation The recording may stop or continue.
CountermeasuresRestart recording. Or, turn the power OFF 
and turn it ON again, before starting 
recording. 
6. Image Sequence Error (24P, 30P, 25P)
Display window 
indication “E-40” appears in the time code display field.
WARNING lamp Blinks 4 times per second. 
Tally lampBlinks 4 times per second while recording 
continues. 
ViewfinderThe REC WARNING indicator lights up. 
Warning toneBeeps 4 times per second while recording 
continues. 
Warning 
description There are abnormal conditions in the image 
sequence of the 24P, 30P, or 25P mode.
Recording/
playback 
operation Images can be recorded and played back, 
but some frames may be dropped or the 
sequences of TC and UB may shift.
Countermeasures
Confirm the recording/playback operation after 
turning OFF the power supply once and then 
turning it on again. If the error is not corrected 
after executing this procedure, contact the 
dealer.
8. Low Wireless Signal Reception
Display window 
indication No display. 
WARNING lamp Blinks 4 times per second. (During pause 
and recording) 
Tally lampBlinks 4 times per second while recording 
continues. 
ViewfinderThe WIRELESS RF indicator lights up while 
recording continues. 
Warning toneBeeps 4 times per second while recording 
continues. 
Warning 
description This error indicates poor wireless audio 
reception conditions. 
Recording/
playback 
operation Continues to operate without receiving the 
wireless microphone signal. 
CountermeasuresCheck the microphone power supply and the 
reception status of the wireless receiver. 
AJ-HPX2000P(VQT1D27-1)E.book  146 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							147Maintenance and Inspections : Warning System
 Maintenance and Inspections
9. 1394  Error
Display window 
indication The 1394 E-¢¢ indicator in the display 
window blinks. For more information, see  
[
1394 Error Codes] (page 148).
WARNING lamp Blinks 4 times per second while the 
WARNING lamp recording is continuing.
Tally lampBlinks 4 times per second while the TALLY 
LAMP recording is continuing.
ViewfinderIn the case of Error Code 92, “1394 INITIAL 
ERROR” indicator lights up (during pause 
and recording)
For Error Codes other than Error Code 92, or 
if REC SIGNAL is set to “1394”, no error is 
displayed in the viewfinder.
Warning toneBeeps 4 times per second while ALARM 
recording is continuing.
Warning 
description This indicates a failure of the DVCPRO/DV 
connector.
Recording/
playback 
operation The operation continues, but input signals to 
the DVCPRO/DV connector are abnormal. 
For more information, see  [
1394 Error 
Codes] (page 148).
Countermeasures
Check the connection between the 
IEEE1394 cable and the DVCPRO/DV 
connector, settings of any external device 
and menus, and the turn on the power again.
If the warning indication is still illuminated, 
confirm the “
1394 Error Codes” (page 148), 
and consult your distributor.
12. P2 Card Error
Display window 
indication If the error occurs during recording, 
“00:0000:11” appears as the time code 
indication. The indication continues to flash 
after recording is stopped and until the next 
operation is performed. There is no 
indication if the error occurs during playback.
WARNING lamp If the error occurs during recording, the lamp 
flashes four times per second for a period of 
about three seconds. The lamp does not 
light if the error occurs during playback.
Tally lampIf the error occurs during recording, the lamp 
flashes four times per second for a period of 
about three seconds. The lamp does not 
light if the error occurs during playback.
Viewfinder
A flashing “CARD ERR ¢” appears. In the 
actual indication the ¢ is replaced by the slot 
number of the P2 card that triggered the error.
Warning toneIf the error occurs during recording, the tone 
sounds four times per second for a period of 
about three seconds. The tone does not 
sound if the error occurs during playback.
Warning 
description An error has occurred while recording data 
to or playing data from a P2 card.
Recording/
playback 
operation Stop recording or playback.
CountermeasuresReplace the affected P2 card.
10. Battery Nearly Empty
Display window 
indication One of the bars in the battery remaining 
indicator starts blinking. 
WARNING lamp Blinks once per second. 
Tally lampBlinks once per second. 
ViewfinderThe BATT LED blinks. 
Warning toneBeeps 4 times per second. 
Warning 
description The battery is about to run out. 
Recording/
playback 
operation Continues to operate. 
CountermeasuresReplace the battery as required. 
13. FAN STOP
Display window 
indication No display. 
WARNING lamp Blinks 4 times per second. 
Tally lampNo display. 
ViewfinderThe FAN STOP indicator blinks while 
recording continues. 
Warning toneIt does not sound.
Warning 
description The fan is at rest because something is 
wrong with it.
Recording/
playback 
operation If the camera-recorder operates with the fan 
stopped, then the temperature inside rises. 
While the camera-recorder continues to 
operate, clips may not be recorded or played 
back properly. 
CountermeasuresImmediately stop using the camera-recorder 
and consult your distributor.
11. P2 Card Nearly Full
Display window 
indication One of the bars for remaining MEDIA 
capacity starts blinking. 
WARNING lamp Blinks once per second while recording 
continues. 
Tally lampBlinks once per second while recording 
continues. 
Viewfinder
The P2 card remaining capacity indicator blinks.
Warning toneBeeps once per second while recording 
continues. 
Warning 
description The total remaining capacity of all the P2 
cards is two minutes or less. 
Recording/
playback 
operation Continues to operate. 
CountermeasuresReplace the cards. If there is an empty card 
slot, insert a new card. 
AJ-HPX2000P(VQT1D27-1)E.book  147 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							148Maintenance and Inspections : Warning System The following error codes are displayed in the display window if an error occurs in the camera: 
Confirm the type of warning and refer to the details in the [Warning Description Tables] (page 145) for countermeasures.
Error Codes
Code No.  Description  Type of warnings
E-11 Video initialisation error 1. System Errors
E-27 Recording control error 1. System Errors
E-30 P2 card removal error 2. 
Card removal error
E-34 LCD microcontroller error 1. System Errors
E-38 P2 streaming microcontroller error 1. System Errors
E-39
Abnormal initialization of the AVC-Intra codec board (optional AJ-YBX200G)1. System Errors
E-3F Microprocessor error in the camera control circuit.  1. System Errors
E-40 Image sequence error (in case of 24P, 30P and 25P) 6. 
Image Sequence Error (24P, 30P, 25P)
E-63 Something is wrong with the system control microprocessor. 1. System Errors
E-6F Reference signal error.  1. System Errors
00:00:00:11 Recording error on a P2 card 7. Recording Error
1394 Error Codes
Code No.  Description  RecordingIndication in display 
window
1394 E-80Signals being input to the DVCPRO/DV 
connector are not 1
a speed transfer 
signals in DV format.Stops
The time code section of the 
display window indicates the 
appropriate error code that 
blinks every two seconds. 1394 E-81Signals being input to the DVCPRO/DV 
connector are not 1
a speed transfer 
signals in DVCPRO (25 Mbps) format.Stops
1394 E-82Signals being input to the DVCPRO/DV 
connector are not 1
a speed transfer 
signals in DVCPRO50 (50 Mbps) format.Stops
1394 E-83Incorrect signals are being input to the 
DVCPRO/DV connector.Stops
1394 E-84Signals being input to the DVCPRO/DV 
connector are not in DVCPRO or DV 
for mat.Stops
1394 E-85Signals being input to the DVCPRO/DV 
connector are not 1x speed transfer signals 
in DVCPRO HD format.Stops
1394 E-87Incorrect audio signals are being input to 
the DVCPRO/DV connector.Continues with no sound.
1394 E-90No signal is supplied to the DVCPRO/DV 
connector.While the recording mode continues, no 
data is recorded on cards unless the 
abnormal condition is corrected. If an 
error has occurred before recording, then, 
recording does not start.
1394 E-91With the menu option REC MODE set to 
DV, copy guard information signals for 
recording prohibited data are being input to 
the DVCPRO/DV connector.Stops
1394 E-92The DVCPRO/DV connector is not properly 
connected. The viewfinder indicates the 
message 1394 INITIAL ERROR.No recording in 1394 input mode can be 
performed.
AJ-HPX2000P(VQT1D27-1)E.book  148 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							149Maintenance and Inspections : Warning System
 Maintenance and Inspections
Card Warning Code
Code No.  Description  RecordingIndication in display 
window
E-70
The directory organization on the inserted P2 
card does not comply with the standards. ([DIR 
NG CARD (Slot No.)] is indicated on the 
viewfinder.)Although different kinds of recording 
operations will function, data may not be 
recorded properly. Use the unit to format the 
card immediately.A warning code blinks once 
every 2 seconds on the time 
code display section of the 
display window.
E-71
A P2 card was inserted where the number of 
rewrites exceeds the limit of the standards. 
([RUN DOWN CARD (Slot No.)] is indicated on 
the viewfinder.)Although different kinds of recording 
operations will function, data may not be 
recorded properly. It is recommended to 
replace it.
Warning and Error Display for Thumbnail Operation and USB HOST MODE
ItemMessageDescriptionMeasure
ThumbnailsCANNOT ACCESS! Data cannot be accessed because it is 
corrupted or for other reasons. Restore media and clips to normal state before 
access. 
WRITE 
PROTECTED!The P2 or SD card is write protected.  Insert write-enabled media. 
CARD FULL! The P2 or SD card is full.  Insert media with sufficient capacity. 
NO CARD! No P2 or SD card is inserted.  Insert compatible media. 
NO FILE! The designated file is not found. Check the file.
CANNOT COPY! Images cannot be copied. Check the conditions for copying.
CANNOT DELETE ! Contents version mismatch prevents 
deletion. Match devices and contents version. 
UNKNOWN 
CONTENTS 
FORMAT!Warning displayed to indicate contents 
version mismatch. Match devices and contents version. 
CANNOT FORMAT! P2 card problem prevents formatting.  Check P2 card. 
CANNOT REPAIR! Data cannot be repaired since content that 
cannot be repaired is selected.Check selected content. 
CANNOT RE-
CONNECT!A clip that does not span 
multiple P2 cards 
cannot be reconnected. Check selected content. 
INVALID VALUE! Entered data was invalid. Enter data in a valid range. 
UNKNOWN DATA! The metadata character code is invalid.  Use UTF-8 for the metadata character code. Use 
the viewer to enter correct characters. 
CANNOT REPAIR IN 
SELECTION!Some of the selected clip could not be 
repaired.
NO SD CARD! No SD card is inserted. Insert an SD card.
NO COPY TO SAME 
CARD!A clip cannot be copied to the card storing 
the original clip. Copy the selected clip to a card that does not 
contain the original clip. 
SAME CLIP IS 
SELECTED!The clip cannot be copied because a clip that 
has already been copied and the original clip 
have been selected.
Confirm the selected clip and release either the 
source clip or the destination clip and then execute 
the copy operation.
USER CLIP NAME 
MODIFIED!Characters in the clip name had to be 
deleted in adding the counter value. The user clip name plus the counter value can only 
contain up to 100 bytes. Characters in the clip 
name are automatically deleted when the total 
exceeds 100 bytes. 
TOO MANY CLIPS! Too many clips are selected.  Reduce the number of selected clips. 
LACK OF REC 
CAPACITY!There is not enough recording capacity left 
on the card. Insert a card with sufficient recording capacity. 
CANNOT CHANGE! Any thumbnails that cannot be produced on 
the AVC-Intra 100 or AVC-Intra 50 and 
displayed in gray cannot be changed at the 
text memo position.Install the AVC-Intra codec board (AJ-YBX200G, 
optional) and set SYSTEM MODE according to the 
clips.
MISSING CLIP!
A shot mark will be added to the clips recorded 
on multiple P2 cards when all P2 cards are not 
inserted yet.Insert all P2 cards with recorded clips, and confirm 
that the   incomplete clip indicators disappear, and 
then add shot marks.
AJ-HPX2000P(VQT1D27-1)E.book  149 ページ  ２００７年７月３０日　月曜日　午後１時３１分 
						

							150Maintenance and Inspections : Warning System
Soft 
keyboard
CANNOT CHANGE! [PERSON] will be entered while the text 
memo is not available.Enter [TEXT] before entering [PERSON].
CANNOT SET!
I N VA L I D  VA L U E !The entered value is incorrect. Change the value.
HDD
¢USB HOST 
MODE
£
HDD CAPACITY 
FULL!Not enough space left on the hard disk.  There is not enough space on the connected hard 
disk. Use a new hard disk or formatted hard disk. 
TOO MANY 
PARTITIONS!There are too many partitions.  Hard disks can handle up to 23 partitions. Use a 
new hard disk or formatted hard disk. 
HDD 
DISCONNECTED!The unit is not connected to a hard disk.  Reconnect the USB cable. If the hard disk does 
not operate normally, turn it off and turn it back on 
again. 
CANNOT FORMAT! The hard disk cannot be initialized.  Connect another hard disk drive. 
TOO MANY 
TA R G E T S !Multiple devices are connected.  Disconnect devices, turn off the unit and turn it 
back on again. 
UNKNOWN DEVICE 
CONNECTED!The connected DVD drive is not compatible.  Disconnect devices, turn off the unit and turn it 
back on again. 
CANNOT ACCESS 
TA R G E T !An error occurred during hard disk access.  Check hard disk status and connection. 
CANNOT 
RECOGNIZE
HDD!The destination target cannot be properly 
recognized. Reboot the hard disk or connect a different hard 
disk. 
CANNOT ACCESS 
CARD!An error occurred during P2 card access.  Check P2 card. 
MISMATCH 
COMPONENT!Copying cannot be made because the 
destination card is in the wrong format. Use a P2 card with appropriate capacity.
P2 CARD IS 
UNFORMATTED!The P2 card is not formatted.  Use a formatted P2 card. 
CARD IS EMPTY! 
CANNOT COPY!The P2 selected for copying is empty.  Copying is not performed since the card is empty. 
VERIFICATION 
FA I L E D !The compare check after copying failed.  Copy the data again. 
PLEASE FORMAT 
P2 CARD!This warning indicates that data could not be 
imported from a hard disk to a P2 card 
because the P2 card contained recorded 
data. You cannot copy to a P2 card that contains data. 
Format the card on a P2 device and copy again. 
ItemMessageDescriptionMeasure
AJ-HPX2000P(VQT1D27-1)E.book  150 ページ  ２００７年７月３０日　月曜日　午後１時３１分