Panasonic Matrix Switcher Wj Sx550c Operating Instructions

							Backlight Compensation (BLC) Mode
The following function requires the use of cameras
equipped with the specific feature.
1. Select the desired Monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the BLC (D2)Menu on the LCD display by
pressing the appropriate Direction button.
3. Press the Function (F1)button to toggle the Auto BLC
Mode on and off.
4. Press the Function (F2)button to toggle the Preset BLC
Mode on and off. b) Selecting Area before Zooming Procedures:
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Ele Zoom (C3) Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Press the Function (F2) button to select the Zooming
Position Mode.
4. Press the Function (F3 orF4)button repeatedly to
select the desired zooming area.
The emphasized area is switched over on the monitor
as shown in the previous table.
5. Press the Function (F1) button to select the Electronic
Zoom Mode.
A zoomed picture of the area selected in step 4 above
appears on the monitor.
6. Press the Function (F1) button to turn the Electronic
Zoom Mode off.
116
5
F1 F2F3F4
Ele Zoom Posi
 On   Off  <   >
F1 F2F3F4
Ele Zoom On
 Off Posi  <   >
F1 F2F3F4
F1 F2
F3F4
Ele zoom OFF
 ON  Posi
Ele Zoom On
 Off Posi  <   >
F1 F2F3F4
BLC Off
Auto Preset D2
F1 F2F3F4
Ele Zoom Off
 On  Posi
F1 F2F3F4
Ele Zoom Posi
 On   Off  <   > C3
F1 F2F3F4
BLC Off
Auto Preset
F1 F2F3F4
BLC Preset
Auto Off
F1 F2F3F4
BLC Off
Auto Preset
F1 F2F3F4
BLC Auto
Off  Preset 
						

							117
5
Camera Setup
The following function requires the use of cameras
equipped with the specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Camera Set Up (D4)Menu on the LCD dis-
play by pressing the appropriate Direction button.
Note:The default setting for the Camera Setup Menu is
On. Pressing the Function (F1)button at this
moment will allow access to the Camera Set up
menu if such access is authorized by the opera-
tors level.
If “PROHIBITED” appears on the LCD display,
press the MON (ESC) key to return the Camera Set
Up Menu display.
3. Press the Function(F1)button to gain access to the
Camera Set Up Menu.
The menu displayed may look as follows:
F2F3F4
Camera Set Up Menu
 On             Exit
F1
D4
4. Select the desired item parameter by moving the
Joystick Controller UP and DOWN, and then select the
desired desired mode by moving the Joystick
Controller LEFT and RIGHT.
Press the CAM (SET)key to execute the setting or
enter sub menu, and press the MON (ESC)key to
escape from the setup mode or menu.
5. Press the Function (F2) button to reset the selected
menu, or press the Function (F3)button to reset all set-
tings to factory default setting.
Refer to the Operating Instructions of the selected cam-
era for further details.
Note
6. Press the Function (F4)button to return to the original
screen.
Caution: If camera setup is started with buttons on the
camera, all settings must be made with the buttons
on the cameras.
If camera setup is started with a Matrix Switcher, all
settings must be made with the Matrix Switcher.
    ** SET UP **
CAMERA ID    OFF
ALC/ELC      ALC
SHUTTER      OFF
AGC          ON
SENSE UP     OFF
SYNC         INT
WHITE BAL    ATW
WIDE D-RANGE OFF
MOTION DET   OFF
DNR          OFF
 END    SET UP ENABLE
Camera Set Up Menu
     Res A.Res  Exit
F1 F2 F3F4 
						

							Changing to Black and White Pictures
The following function is available only when specified cam-
eras with color-black and white switching feature are used.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the BW (C4)Menu on the LCD display by press-
ing the Direction buttons.
3. Press the Function (F1) button.
The picture will change from color to black and white
picture on the active monitor.
4. Press the Function (F2) button.
The black and white picture changes back to color on
the monitor.
Note: When the black and white parameter is set to
AUTO in the camera setup menu, this function is
disabled.
Camera Function (Shortcut Function)
The following function is available only when specified cam-
eras with the camera function feature is used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Camera Function (C5) Menu on the LCD dis-
play by pressing the Direction buttons.
3. Select an assigned function number by pressing the
Numeric keys, then press the Function (F1)button.
For example, enter 175 for AGC on.
The selected function will be executed on the active
monitor.
Note: For further information, refer to the Operating
Instructions for that camera.
118
5
F2F3F4
BW
 ON    OFF
F1
C4
F2F3F4
CameraFunction
 CamFUNC.
F1
C5
Auxiliary Control
The following function is available only when WV-RC100 or
WV-RC150 Receivers are included in the system.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Pressing the AUX 1 or2 button will toggle the users
auxiliary switch in the Receiver (WV-RC100 or WV-
RC150) on and off.
12AUX 
						

							119
5
Note:“AL0” or “AL1” is displayed in the upper right
corner of the alarmed monitor.
To Cancel Alarm (Plural Monitors)
The following function is used to cancel alarm in a lump
when Alarm Mode 1 or 2 is activated.
1. Select the alarmed monitor.
Select Monitor 1 if Alarm Mode 1 is activated, or one of
Monitors 1 - 4 if Alarm Mode 2 is activated.
2. Press the ALTbutton. The LED indicator on the button
lights.
3. Press the ACK RESETbutton once for alarm acknowl-
edgment.
The LED indicator on the button blinks rapidly.
4. Press the ACK RESETbutton once again for alarm
reset.
The LED indicator on the button goes off.
Note:Select one of the monitors, that is running the
Group Sequence by activating the Alarm Mode 3,
then follow the steps above to cancel the alarmed
monitors at once.
Alarm Control
Alarm Input Selection
The following settings enable or disable alarm inputs from
the camera site or Alarm Board after the Alarm Mode Select
item has been set in the Setup Menu.
1. Select the Alarm in (A5) Menu on the LCD display by
pressing the appropriate Direction button.
2. Press the Function (F1) button to toggle the Camera
Site Alarm on and off.
3. Press the Function (F2)button to toggle the Interface
Alarm (Alarm Board) on and off.
Alarm Operation
When an alarm is activated, the ALARMindicator on the
controller blinks.
The indicator keeps blinking until all alarms are cleared by
pressing the ACK RESETbutton.
To Cancel Alarm (Single Monitor)
1. The alarmed monitor(s) must first be selected.
Refer to the Monitor Selection.
2. Press the ACK RESETbutton once for alarm acknowl-
edgment.
The LED indicator on the button blinks rapidly.
3. Press the ACK RESET button once again for alarm
reset.
The ALARM indicator goes off, and the LED indicator
on the button goes off.
ALARM LED
ACK
RESETACK
RESET
F1F2
Alarm in
 Site  Board
A5
On:   Site Board
Off:   Site Board
MAY 0700 14:23:56  ALO
C 01 M16 3rd Floor
         Room  306
ACK
RESETACK
RESETALT 
						

							Preset Setting (WV-CS500 Only)
The following function is only available with the WV-CS500
camera that has preset panning functions.
Preset Menu Setting
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Preset (D3)Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Press the Function (F1) button to select the Preset
Program Mode.
The PRESET PROGRAM Menu appears on the active
monitor.
Refer to the Preset Program Menu shown below.
Press the Function (F2) button to select the Refresh
Mode.
The Pan/Tilt/Zoom/Focus functions of the selected cam-
era are automatically activated.
.
Note: Use the refresh mode if the preset positions
become slightly different from the default positions.
120
5
Preset Menu:CS500
 On  Refresh
F1 F2F3F4
Preset/BLC Clear
 Pre  BLC
F1 F2F3F4
F1 F2F3F4
Preset Menu:CS500
 On  Refresh D3
Preset Program Menu
As shown below, the Preset Program Menu has three sub-
menus:
SET UP PRESET, SET HOME POSI (Position), and PRESET
TEST.
The menu items explained below.
1. SET UP PRESET
Sets up the preset position or preset BLC (Backlight
Compensation) for the camera.
2. SET HOME POSI
Sets up the Home Position for the camera
3. PRESET TEST
Tests all selected preset positions.
To select an item from the Preset Program Menu:
1. Move the cursor to the desired item by moving the
Joystick Controller.
2. To execute the selection, press the CAM (SET)key.
The selected item appears on the monitor.
3. To escape from the menu without changing any set-
tings, press the MON (ESC)key.
CAM    : CameraTitle
   *PRESET PROGRAM*
   1 SET UP PRESET
   2 SET HOME POSI
   3 PRESET TEST
PRESET DATA LOADING... 
						

							121
5
Setting Up Preset Positions
In the PRESET PROGRAM menu, select SET UP PRESET,
and then press the CAM (SET)key. The PRESET NUMBER
SET table shown below appears on the active monitor.
1. Move the cursor to the desired preset number by mov-
ing the Joystick Controller.
2. Press the CAM (SET) key. The Preset Position Setting
table shown below appears on the monitor.
3. Move the camera to the preset position to be registered
by moving the Joystick Controller, and adjust the zoom
and focus by pressing the ZOOM TELE/WIDEand
FOCUS NEAR/ FAR Control.
4. When satisfied with the position, press the CAM (SET)
key.
The Preset BLC (Backlight Compensation) Setting table
shown below appears on the monitor.
5. Move the cursor to the area, where backlight is bright,
by moving the Joystick Controller.
6. Press the INC +1CAM button orDEC –1CAMbutton to
toggle a mask on and off.
7. Repeat the above procedures until mask setting is
completed.
8. Press the CAM (SET) key to execute the setting.
The monitor screen returns to the previous PRESET
NUMBER SET table.
9. Repeat the above procedures to register positions for
other preset numbers.
10. Press the MON (ESC)key to return to the previous
Preset Program Menu.
CAM    : CameraTitle
POSITION NUMBER : 12
     PAN/TILT/ZOOM/FOCUS
     SET UP POSITION
CAM    : CameraTitle
  *PRESET NUMBER SET*
   1#    2#    3#    4#
   5#    6#    7#    8#
   9#   10#   11#   12#
  13#   14#   15#H  16#
  17    18    19    20#
  21    22    23    24
  25    26    27    28
  29    30    31    32 
						

							Home Position Setting
In the PRESET PROGRAM menu, select SET HOME POSI,
and then press the CAM (SET)key. The HOME POSITION
table shown below appears on the active monitor.
1. Move the cursor to the HOME POSITION parameter by
moving the Joystick Controller, then select the desired
position number by pressing the Numeric keys.
2. Move the cursor to the AUTO HOME POSITION para-
meter by moving the Joystick Controller, then select
either mode Off or a desired time by pressing theINC +
1CAMbutton or DEC –1CAMbutton.
3. Press the CAM (SET)key to execute the selection and
return to the previous Preset Program Menu.
Note: When the auto home position function is enabled
a camera will move to the designated home posi-
tion automatically after a predetermined period of
time.
122
5
Preset Test Mode
In the PRESET PROGRAM menu, select PRESET TEST, and
then press the CAM (SET)key. The table shown below
appears on the active monitor.
1. Press theCAM (SET)key to activate the test mode.
The selected camera moves to all preset positions, pro-
ceeding from the lowest preset number to the highest.
The above function will automatically end after ten min-
utes.
2. Press the MON (ESC)key to escape from the preset
test mode.
3. Press the MON (ESC)key again to return to the previ-
ous Preset Program Menu.
CAM    : CameraTitle
POSITION NUMBER : 12
         TEST
       ESC→STOPCAM    : CameraTitle
    *HOME POSITION*
  1 HOME POSITION : 15
  2 AUTO HOME POSITION
                : 10MIN 
						

							123
5
Clearing Preset Settings
1. Select the desired monitor and camera.
Refer to the Monitor Selection and camera Selection.
2. Select the Preset(D3) Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Press the Function (F1) button to select the Preset
Program Mode.
The Preset Program Menu is displayed on the active
monitor, and the LCD display reads as shown below.
4. Move the cursor to SET UP PRESET by moving the
Joystick Controller, then press the CAM (SET) key.
The PRESET NUMBER SET table appears on the active
monitor.
5. Move the cursor to the desired preset number by mov-
ing the Joystick Controller, then press the CAM (SET)
key to select the Preset Position Setting table shown
below.
6. Press the Function (F1)button to clear the presets for
the selected position number.
To clear only the BLC setting, press the Set CAM (SET)
key to select the Preset BLC Setting table, and then
press the Function (F2)button instead of (F1).
7. Pressing the MON (ESC)key repeatedly will return to
the previous setup table or menu.
Preset Menu:CS500
 On  Refresh
F1 F2F3F4
D3
CAM    : CameraTitle
POSITION NUMBER : 12
     PAN/TILT/ZOOM/FOCUS
     SET UP POSITION
Preset/BLC Clear
 Pre  BLC
F1 F2F3F4
Camera Position Number
Setting
The following function is available only when the Mode
Selection Switch located on the rear of the controller is set
to CAM-P Mode, and cameras equipped with the specific
feature are used.
Refer to the Mode Selection on page 54.
Register Camera Position Number
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select the CAM-P (D5)Menu on the LCD display by
pressing the appropriate Direction button.
3. Pressing the Function (F1)button will display the menu
shown below on the LCD display.
Select the camera number by pressing the Numeric
keys, then press the CAM (SET) key.
4. Select the preset position number by pressing the
Numeric keys, then press the CAM (SET) key.
The picture at the selected camera preset position
appears on the active monitor, and the LCD display
reads as shown below.
CAM-P Menu
Set Clear Test Mode
F1 F2F3F4
D5
C
               Exit
C 01 Pre
               Exit
C 01 Pre64 CAM-P
Input OK?-->Set/Esc 
						

							5. Confirm the display on the LCD display, then press the
CAM (SET) key to delete the selected Camera Position
Number.
If a mistake was made in the above steps, press the
MON (ESC) key to cancel the selection.
6. Repeat the above steps for other camera position num-
bers.
When satisfied with all positions, press the Function
(F4) button to exit from the programming mode.
Camera Position Test Mode
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select the CAM-P (D5)Menu shown below on the LCD
display by pressing the appropriate Direction button.
3. Pressing the Function (F3)button will display the menu
shown below on the LCD display.
4. Press the Function (F1)button to toggle the test mode
on and off.
If On mode is selected, the picture at each of the
selected camera positions is displayed on the active
monitor at intervals of 3 seconds, proceeding from the
lowest camera position number to the highest.
124
5
5. Select the Camera Position Number by pressing the
Numeric keys.
After completing the above steps, press the CAM
(SET) key to execute the selection.
If a mistake was made in the above steps, press the
Escape MON (ESC)key to cancel the selection.
Note:Up to 1 000 positions can be registered on this
menu.
If an attempt is made to register more than 1 000
positions, “Data Full” appears on the LCD display.
6. Repeat the above steps for other camera positions.
When satisfied with all positions, press the Function
(F4)button to exit from the programming mode.
Delete Camera Position Number
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select the CAM-P (D5)Menu shown below on the LCD
display by pressing the appropriate Direction buttons.
3. Pressing the Function (F2)button will display the menu
shown below on the LCD display.
4. Enter the camera position number to be deleted by
pressing the Numeric keys, and then press the CAM
(SET)key. The picture at the selected camera position
appears on the active monitor, and the LCD display
reads as shown below.
C
               Exit
F1 F2F3F4
CAM-P Menu
Set Clear Test Mode
F1 F2F3F4
D5
           CAM-P
               Exit
F1 F2 F3 F4
C 01 Pre64 CAM-P9999
Input OK?-->Set/Esc
F1 F2 F3 F4
CAM-P Menu
Set Clear Test Mode
F1 F2F3F4
D5
Test1 CAM-P----
 Act          Exit
F1 F2 F3 F4
Act
ActOff: On:
           CAM-P
               Exit
F1 F2F3F4 
						

							125
5
5. The test function stops automatically, and the LCD dis-
play reads as shown below.
Press the Function (F4)button to exit from the test
mode. The display will return to the previous CAM-P
Menu.
Camera Position Mode Selection
Operation by camera position number is available only
when CAM-P Mode is set to On mode.
1. Select the CAM-P (D5) Menu shown below on the LCD
display by pressing the appropriate Direction button.
2. Pressing the Function (F4) button will display the menu
shown below on the LCD display.
Press the Function (F1)button to toggle the mode on
and off.
3. Press the Function (F4)button to exit from the setup
mode. The display will return to the previous CAM-P
Menu.
Note:Selecting On mode on the LCD display enables
the MON (ESC)key to execute the selection.
When selecting the monitor, enter the desired mon-
itor number by pressing the Numeric keys, and
then press the Function (F1)button instead of the
MON (ESC)key while the Monitor Selection (A1)
Menu is displayed.
Test1 CAM-P9999 End
 -Act          Exit
F1 F2 F3 F4
CAM-P Menu
Set Clear Test Mode
F1 F2 F3 F4
D5
CAM-P Mode Off
 On           Exit
F1 F2 F3 F4
Priority Lock
This function is used by an operator to retain control of a
monitor, even after that operator has selected another mon-
itor or has logged out.
1. Select the Priority Lock (A4) Menu on the LCD display
by pressing the appropriate Direction button.
2. Press the Function(F1)button to select the Priority
Lock mode on the active monitor. 
The monitor number is inversely displayed on the
active monitor, as shown below.
3. Press the Function (F2) button to release the priority
lock.
The monitor number is displayed normally on the moni-
tor.
Note: This function will prevent operators with a lower
priority from gaining control of a monitor.
However, higher priority operators may still gain
control of that monitor.
F1 F2F3F4
PriorityLock
On Off PAuto Log-OutM16
A4