Panasonic Matrix Switcher Wj Sx550c Operating Instructions

							106
Direct Preset Setup
The following function requires the use of cameras
equipped with the specific feature.
This function enables registering of preset position number
without opening the camera setup menu.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Move the camera to the preset position to be regis-
tered by moving the Joystick Controller and ZOOM,
FOCUS Controls.
3. Select the PrePOSI Setup (B5)Menu on the LCD dis-
play by pressing the Direction buttons.
4. Select the desired preset position number by pressing
the Numeric keys, then press the Function (F1) button
to register the position.
Note:If the position number entered has been regis-
tered previously, the old position will be overwritten
by the new one.
23
456
789
MON CAM
ESC SET0
1
PrePOSI SetUp
 Set B5
F1 F2 F3 F4
Patrol Learn and Play
The following function requires the use of cameras
equipped with the specific feature.
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Patrol Learn (B4)Menu on the LCD display
by pressing the Direction buttons.
3. Press the Function (F2)button to start Patrol Learn .
“LEARNING” appears on the active monitor.
4. Operate the camera manually. Operations data is
stored.
The stored data is as show below.
Pan/Tilt, Lens Iris, Focus, Zoom and Preset Position
5. Press the Function (F3)button to end the storage.
To reproduce the stored data, follow the procedure shown
below.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Patrol Learn (B4)Menu on the LCD display
by pressing the Direction buttons.
3. Press the Function (F1)button to reproduce the stored
Patrol function.
4. Press the Function (F3)button to end the reproduction.
PatrolLearn        
 Play Learn Stop
F1 F2F3F4
B4
PatrolLearn        
 Play Learn Stop
F1 F2F3F4
B4
55 
						

							107
5
Camera Power and Housing Control
For remote camera power operation, a 24 V AC powered
camera must be installed in the housing.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Cam-Power Housing (B2) Menu on the LCD
display by pressing the Direction buttons.
3. Press the Function (F1) button to toggle the camera
power on and off.
4. Press the Function (F3) button to toggle the housing
wiper on and off.
5. Press the Function (F4)button to toggle the housing
defroster on and off.
Cam-Power Housing 
 Cam      Wiper Def
F1F2F3F4
B2
F1 On:  Cam
  Off:  Cam
F3 On:  Wiper
  Off:  Wiper
F4On:  Def
Off:  Def
To prevent premature wearing of the wiper blades,
be sure to turn off the wiper when it is not needed or
before selecting another camera for viewing.
Caution
 Running a Sequence
Program Sequence
The following functions are available only if a Program
Sequence has been previously established through the Set
Up Menu.
As described on page 69, the Program Sequence can dis-
play up to 128 cameras in a predetermined series on a
selected monitor.
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select 0 by pressing the Numeric key.
3. Press the FORWARD SEQbutton to run the assigned
Program Sequence in forward direction on the active
monitor.
123
456
789
MON CAM
ESC SET0
A1
Camera  01        
Monitor 16  SLW 
 FST
Camera  01        0
Monitor 16  SLW 
 FST
FORWARD
SEQ
P-Seq
Monitor 16  
						

							8. Press the DEC –1CAM button to move the sequence
one frame to the previous step (in forward or reverse
run direction) from the step that was previously paused
by pressing the STOP button
9. Press the FORWARD SEQ button while the ALT indi-
cator is on to restart the sequence forward from the
beginning of the sequence step that was previously
paused by pressing the STOP button.
10. To return to Spot monitoring, select a camera.
Refer to the Camera Selection.
108
4. Press the STOPbutton to pause the sequence that is
being run on the active monitor.
5. Press the FORWARD SEQbutton to restart the
sequence forward from the step that was previously
paused by pressing the STOP button.
6. Press the BACK SEQ button to restart the  sequence
backward from the step that was previously paused by
pressing the STOP button.
7. Press the INC +1CAMbutton to move the sequence
one frame to the next step (in forward or reverse run
direction) from the step that was previously paused by
pressing the STOP button.
STOP
P-Seq      Stop
Monitor 16 
FORWARD
SEQ
P-Seq
Monitor 16 
BACK
SEQ
P-Seq
Monitor 16 
INC+1CAM
P-Seq      Stop
Monitor 16 
SEQALTFORWARD
DEC-1CAM
P-Seq      Stop
Monitor 16 
55 
						

							109
5
Tour Sequence
The following functions are available only if a Tour
Sequence has been previously established through the Set
Up Menu.
As described on page 70, any one of 32 tours can be
assigned to any one of 16 monitors.
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select the desired Tour Sequence number by pressing
the Numeric keys.
3. Press the FORWARD SEQbutton to run the Tour
Sequence in forward direction on the active monitor.
4. Press the STOP button to pause a Tour Sequence that
is being run on the active monitor.
23
456
789
MON CAM
ESC SET0
1
A1
Camera  01        
Monitor 16  SLW  FST
Camera  01        1
Monitor 16  SLW  FST
FORWARD
SEQ
T-Seq   01
Monitor 16 
STOP
T-Seq   01 Stop
Monitor 16 
5. Press the FORWARD SEQbutton to restart a Tour
Sequence forward from the step that was previously
paused by pressing the STOP button.
6. Press the BACK SEQbutton to restart a Tour
Sequence backward from the step that was previously
paused by pressing the STOP button.
7. Press the INC +1CAM button to move the sequence
one frame to the next step (in forward or reverse run
direction) from the step that was previously paused by
pressing the STOP button.
8. Press the DEC –1CAM button to move the sequence
one frame to the previous step (in forward or reverse
run direction) from the step that was previously paused
by pressing the STOP button.
FORWARD
SEQ
T-Seq   01
Monitor 16 
BACK
SEQ
T-Seq   01
Monitor 16 
INC+1CAM
T-Seq   01 Stop
Monitor 16 
DEC-1CAM
T-Seq   01 Stop
Monitor 16 
						

							110
5
9. Press the FORWARD SEQbutton while the ALTindi-
cator is on to restart the sequence forward from the
beginning of the sequence step that was previously
paused by pressing the STOP button.
10. To return to Spot monitoring, select a camera.
Refer to the Camera Selection.
SEQALTFORWARD
Group Sequence
The following functions are available only if a Group
Sequence has been previously established through the Set
Up Menu.
As described on page 71, up to 8 Group Sequences can
be set up.
1. As described earlier, the Group Sequence determines
which monitor is to be connected to which camera.
Therefore, selecting a monitor is not required.
2. Select G-seq(A2) Menu on the LCD display by press-
ing the Direction buttons.
3. Select the desired Group Sequence number by press-
ing the Function buttons (F3/F4)or the Numeric keys.
4. Press the Function (F1)button to run a Group
Sequence forward on the assigned monitors.
                      
G-Seq      <     > A2
23
456
789
MON CAM
ESC SET0
1
F1F2F3F4
                      
G-Seq      <     >
                 1   
G-Seq      <     >
F1F2F3F4
                 1   
G-Seq      <     >
G-Seq   01
Monitor 16  
						

							111
5
5. Press the STOPbutton to pause a Group Sequence
that is being run on the assigned monitor.
6. Press the FORWARD SEQ button to restart a Group
Sequence forward from the step that was previously
paused by pressing the STOP button.
7. Press the BACK SEQ button to restart a Group
Sequence backward from the step that was previously
paused by pressing the STOP button.
8. Press the INC +1CAMbutton to move the sequence
one frame to the next step (in forward or reverse run
direction) from the step that was previously paused by
pressing the STOP button.
STOP
G-Seq   01 Stop
Monitor 16 
FORWARD
SEQ
G-Seq   01
Monitor 16 
BACKSEQ
G-Seq   01
Monitor 16 
INC+1CAM
G-Seq   01 Stop
Monitor 16 
9. Press the DEC –1CAM button to move the sequence
one frame to the previous step (in forward or reverse
run direction) from the step that was previously paused
by pressing the STOP button.
10. Press the FORWARD SEQ button while the ALTindi-
cator is on to restart the sequence forward from the
beginning of the sequence step that was previously
paused by pressing the STOP button.
11. To return to Spot monitoring, select a camera.
Refer to the Camera Selection.
DEC-1CAM
G-Seq   01 Stop
Monitor 16 
SEQALTFORWARD 
						

							112
5
Displaying Playback Video
If the VCRs Video Output is connected to the Monitor Input
(MONITOR IN) Connector on the WV-PB5504A Video
Output Board, the VCRs video can be displayed on the
monitor by the following procedures.
When this function is selected, the Camera Title, Date, and
Time are not displayed on the active monitor.
1. Select the monitor connected to the Monitor Output
(MONITOR OUT)Connector systemized with the con-
nected VCRs Monitor Input (MONITOR IN)Connector.
Refer to the Monitor Selection.
2. Press the ALTbutton (indicator is on), then press the
MON (ESC) key.
The picture on the active monitor will be replaced by
the video output connected to the Video Output Board.
The display “in” appears on the LCD display as shown
below.
3. Press the ALT button again (indicator is off) to return to
the original picture.
23
456
789
0
1
ALT
A1
MON CAM
ESC SET
Camera  01
Monitor 01 [in]  SLW 
 FST
 Title Display
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Display (A3) Menu on the LCD display by
pressing the Direction buttons.
3. Press the Function (F1) button to toggle all items dis-
played on the active monitor on and off.
4. Press the Function (F2) button to toggle the monitor
status display on the active monitor on and off.
F1F3F4
Display           
 All Mon Time Title
MAY 0700 14:23:56
C 01 M16 3rd Floor
Pr64 Sp  Room  306
F2
A3
F1
MAY 0700 14:23:56
C 01 M16 3rd Floor
Pr64 Sp  Room  306
F2
MAY 0700 14:23:56
C 01 M16 3rd Floor
Pr64 Sp  Room  306 
						

							113
5
Camera Status Display
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Pan Action (B1)Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Press the Function (F4)button to toggle the camera
status display shown below on and off. 5. Press the Function (F3)button to toggle the date and
time display on the active monitor on and off.
6. Press the Function (F4) button to toggle the camera
title display on the active monitor on and off.
F3
MAY 0700 14:23:56
C 01 M16 3rd Floor
Pr64 Sp  Room  306
F4
MAY 0700 14:23:56
C 01 M16 3rd Floor
Pr64 Sp  Room  306
Site Status
Ele Zoom:
Shutter :
Sens Up :
Random  :
Auto Pan:
Camera  :
Wiper   :
Def     :
AUX1    :
AUX2    :
C01  M16
F1F2F3F4
Pan Action
 Auto  Random Status
B1 
						

							114
5
Camera Function Operation
Electronic Shutter Mode
The following function requires the use of cameras
equipped with the specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Shutter(C1)Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Select Shutter On mode by pressing the Function (F1)
button.
Pressing the Function (F3)button will select slower
shutter speeds, or pressing the Function (F4) button
will select faster shutter speeds.
F3: 1/10 000 → 1/4 000 →1/2 000 →1/1 000 →1/500
→1/250 →1/100
F4: 1/100 →1/200 →1/400 →1/1 000 →1/2 000 
→1/4 000 →1/10 000
Note:The shutter speed varies by the selected cam-
eras.
4. Press the Function(F1)button to turn the electronic
shutter mode off.
Shutter Off        
 On
C1
F1F2F3F4
Shutter Off
 On
F1F2F3F4
Shutter On
 Off        <   >
F1F2F3F4
Shutter Off
 On
Shutter On
 Off        <   >
Electronic Sensitivity Up Mode
The following function requires the use of cameras
equipped with the specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Sens Up (C2) Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Press the Function(F1)button to toggle the Auto
Sensitivity Up Mode on and off.
4. Press the Function (F2)button to toggle the Manual
Sensitivity Up Mode on and off.
5. In the On mode, pressing the Function(F3) button will
select a lower sensitivity setting, or pressing the
Function (F4) button will select a higher sensitivity set-
ting in the selected mode.
F3: X10 → X6 → X4 → X2 → X1
F4: X1 → X2 → X4 → X6 → X10
Note:The sensitivity varies by the selected cameras.
6. Press the Function (F1)button (or Function (F2)button)
to turn the Sensitivity Up Mode off.
F1F2F3F4
Sens Up Off
Auto Manual C2
F1F2F3F4
Sens Up Off
Auto Manual
F1 F2F3F4
Sens Up Auto
Off  Manual <   >
F1 F2F3F4
Sens Up Off
Auto Manual
F1 F2F3F4
Sens Up Manual
Auto Off    <   > 
						

							115
5
Key No.
Electronic Zoom Mode
The following function requires the use of cameras
equipped with the specific feature.
a) Selecting Area after Zooming Procedures:
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Select the Ele Zoom (C3) Menu on the LCD display by
pressing the appropriate Direction buttons.
3. Select Ele Zoom On mode by pressing the Function
(F1)button.
A Zoomed picture appears on the active monitor with
the area that was last selected.
4. Press the Function (F3 orF4) button repeatedly to
select the desired zoomed area.
The zoomed area is switched over as shown in the fol-
lowing table.
F1F2F3F4
Ele Zoom Off
 On  Posi C3
F1F2F3F4
Ele Zoom Off
 On  Posi
F1F2F3F4
Ele Zoom On
 Off Posi   <   >
Selected Area
→→→→
→→→→ F3
F4q w e r
t
qwert
5. Press the Function (F1)button to turn the Electronic
Zoom Mode off.
F1 F2F3F4
Ele Zoom On
 Off  Posi
F1 F2F3F4
Ele Zoom Off
 On   Posi  <   >
w
e
rt q