Panasonic LCD Projector Pt Vx42 Operating Instructions

Contents of mail sent
Example of E-mail sent when E-mail is set
Mail with the contents shown below is sent when the e-mail settings have been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Ty pe          : PT-VX605N
Serial No               : SH1234567
-----  E-m ail setup d ata -----
TEMPER ATURE WARNING SETUP 
MINIMUM TIME            at [ 60] minutes interval 
INTAKE AIR TEMPER ATURE  Over [ 32degC / 89degF ] 
ERROR                   [ OFF ] 
LA MP RUNTIME      
      [ OFF ]   at...

Example of E-mail sent for an error
Mail with the contents shown below is sent when an error has occurred.
=== Panasonic projector report(ERROR) ===
Projector Ty pe          : PT-VX605N
Serial No               : SH1234567
-----  check syste m -----
FAN                           [   OK   ]
INTAKE AIR TEMPER ATURE 
       [   OK   ]
EXHAUST AIR TEMPER ATURE       [   OK   ]
LA MP REM AIN TIME              [   OK   ]
LA MP STATUS                   [   OK   ]
APERTURE (CONTR AST-SHUTTER) 
  [   OK   ]
AIR...

1 [LAMP POWER]Selects the [LAMP POWER] setting.
2 [AUTO POWER SAVE]Select [ON] to set [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION], and [AV MUTE DETECTION].
3 [AMBIENT LIGHT DETECTION]Enable ([ON])/disable ([OFF]) the ambient light detection function. 
4 [SIGNAL DETECTION]Enable ([ON])/disable ([OFF]) the signal detection function.
5 [AV MUTE DETECTION]Enable ([ON])/disable ([OFF]) the AV mute detection function.
6 [POWER MANAGEMENT]Select the power consumption mode.
7 [TIMER]Select the time that the...

[Administrator] account
1
2
3
4
1 [Account]
Displays the account to change. 
2 [Current]  
[User name]:
Enter the user name before the change.
[Password]:
Enter the current password.
3 [New]  
[User name]:
Enter the desired new user name.  
(Up to 16 characters in single byte)
[Password]:
Enter the desired new password.  
(Up to 16 characters in single byte)
[Password (Retype)]:
Enter the desired new password again.
4 [OK]
Determines the change of password.
[User] account
1
2
3
1 [Account]
Displays the...

[Change password] (For user rights)
Only the change of password is enabled under the user rights.
1
2
4 3
1 [Old Password]
Enter the current password.
2 [New Password]
Enter the desired new password. (Up to 16 characters 
in single byte)
3 [Retype]
Enter the desired new password again.
4 [OK]
Determines the change of password.
Note
 fTo change the account of the administrator, you must enter the [User name] and [Password] in [Current].
[Crestron Connected(TM)] page 
The projector can be...

[Tools] page
Click [Tools] on the control page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the 
controller to be connected with the projector.
2 [User Password]
Set the user rights password for the Crestron 
Connected™ control page.
3 [Admin Password]
Set the administrator rights password for the Crestron 
Connected™ control page.
4 Network statusDisplays the settings of wired LAN.
[DHCP]Displays the current setting.[IpAddress]Displays the current...

[Help] page
Click [Help] on the control page.
The [Help Desk] window is displayed.
1
1 [Help Desk]Send/receive messages to/from an administrator who uses Crestron Connected™.
ENGLISH - 11 7
Chapter 4   Settings - [NETWORK/USB] menu  

Chapter 5   Operation of Function
This chapter describes the operation methods of some functions.
11 8 - ENGLISH  

Memory Viewer function
The Memory Viewer function makes it is possible to project the video or still image \
stored in the USB memory.
What you can project with the Memory Viewer function
Memory Viewer function supports the following files.
Video
ExtensionVideo codecAudio codecVideo formatAudio format
movH.264/AVC
MotionJpeg
AAC
Linear PCM
Maximum:
1 920 x 1 080/30 fps 
Maximum:
48 kHz 2 ch
(It is up to 16 kHz 
stereo when the codec 
is linear PCM)
avi
H.264/AVC
MotionJpeg
Mpeg4
mp3
AAC
Linear PCM...

Note
 fThe USB memory can be inserted or removed regardless of the power status\
 of the projector.
Displaying the Memory Viewer screen
1) Insert the USB memory in which the video or still image file is stored i\
nto the  
terminal.
 fFor more information about using USB memory, refer to “Cautions on using USB Memory”. (x page 119)
2) Press the  button.
 fThe memory viewer screen (in thumbnail or list display) will be projected.
 fA cursor will be displayed in the thumbnail display area or the list...