Panasonic LCD Projector Pt Vx42 Operating Instructions

 fThe file starts playing on the full screen.
 fFor the detailed information on the playing order, refer to the “Playing the still image” (x page 121) or “Playing the 
video”(x page 123).
5) Press the  button to exit playing.
 f 
Exit the full screen display, and the Memory Viewer screen (in thumbnail display) is displayed.
 fIf you want to continue to play another file,  please perform the step 1) to 4) again.
Note
 fWhen Memory Viewer screen is displayed, each time you press the  button, the cursor...

 Operation Guide
Display example of auto playing (still image)
When the automatic playback function is enable
Introduce the procedure of the operation under the [MEMORY VIEWER] menu → [AUTOPLAY] is set to [ON]. (x page 96)
All images in the same folder will play automatically when [MEMORY VIEWER] menu → [INTERVAL] or [EFFECT] is set to the 
special setting.(x page 96)
1) Press asqw to select a file which you want to play first from the thumbnail, and t\
hen press the 
 button.
 fIt will start playing in...

Playing the video
Introduce the procedure to the example of the operation in the MEMORY VIEWER screen of [THUMBNAIL] display method.
In the case of the MEMORY VIEWER screen of [LIST] display method, you can play with the same procedure other than the 
selection operation of file.
 í”
Ý Çá”
6
\

2) Press the  button.
 fExit the automatic playback and returns to the MEMORY VIEWER screen (thumbnails).
Note
 fIf the number of recording pixels is less than 1 280 × 800, it will be enlarged while maintaining the aspect ratio.
 fIf the number of recording pixels is more than 1 280 × 800, it will be reduced display while maintaining the aspect ratio.
 fThe order of playback, please follow the order that you set on the [MEMORY VIEWER] menu→ [SORT]. (x page 96) 
Even if the video files and still image...

About Miracast
This function is to project the displayed images on the Miracast-certified device to the projector through the wireless LAN 
connection.
Connecting with the Miracast certified-device 
1) Press the  button on the remote control.
 fSwitch the Miracast input, and the Miracast idle screen will display. 
 fYou can also select the Miracast input by pressing the  button on the control panel.
2) Start the Miracast application of the correspondent Miracast devices and\
 PC.
 fCheck the projector...

Chapter 6   Maintenance
This chapter describes methods of inspection when there are problems, ma\
intenance, and 
replacement of the units.
126 - ENGLISH  

Lamp and Temperature indicators
When an indicator lights up
If a problem should occur inside the projector, the lamp indicator  and the temperature indicator  will inform 
you by lighting or blinking. Check the status of the indicators and remedy the indicated problems as follows.
Attention
 fBefore you take a remedial measure, follow the procedure of switching the power off indicated in “Powering Off the 
Projector”. (Æ page 44)
Lamp indicator 
Temperature indicator 
Lamp indicator 
Indicator...

Maintenance/replacement
Before performing maintenance/replacement
 fMake sure to turn off the power before maintaining the projector or replacing the unit.(Æ pages 44, 41)
 fWhen switching off the projector, make sure to follow the procedures in “Powering Off the Projector”. (Æ page 44)
Maintenance
Outer case
Wipe off dirt and dust with a soft, dry cloth.
 fIf the dirt is persistent, soak the cloth with water and wring it thorou\
ghly before wiping. Dry off the projector with a dry cloth.
 fDo not use...

Ta bAir filter unit
3) Attach the optional Replacement Filter Unit (Model No.: ET
-RFV400) to the projector.
 fHold the air filter unit that the tab is in left side in the figure, put the right side in the figure first, and press the tab until 
make a click sound.
 fPlease press the tab of the air filter unit other than the pleated filter during installation.
Ta bAir filter unit
4) Attach the air filter cover to the projector.
 fPerform Step 1) in “How to replace the air filter unit” (x page 128) in the...

 fWhen replacing the lamp unit, be sure to hold it by the handle. fWhen replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you sho\
uld always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your...