Panasonic LCD Projector Pt Vw350 Operating Instructions

 fDo not set the projector in the elevation of 2 700 m (8 858′) or above, otherwise it may shorten the life of the internal parts and result in malfunctions. fWhen it is set to [HIGH1] or [HIGH2], the fan noise becomes louder and fan speed increases.
[LAMP POWER]
Switch the brightness of the lamp according to the operating environment\
 of the projector or the purpose.
1) Press as to select [LAMP POWER]. 
2) Press qw to switch the item.
 fThe items will switch each time you press the button....

[SHUT DOWN]The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turned off and cooled down when reached the set time, then the projector enter into standby st\
atus. 
[OFF]Power management function is off.
[READY]The countdown timer is displayed after 30 seconds without input signal. \
The projection lamp turns off and cools down when reaching the set time, meanwhile the projector is in the power\
 management mode. The projection lamp will be turned on if the...

[VX500 SERIES]VW435N series, VW440 series, VW430 series, VX505N series, VX510 series, VX500 series, VW330 series, VX400NT series, VX400 series, VX41 series  
[EZ570 SERIES]EZ570 series, EW630 series, EW530 series, EX600 series,  EX500 series
[VW431D]VW431D series
4) Press the  button.
[FUNCTION BUTTON]
The function assigned to the  button of the remote control is displayed. You can also release the assigned 
setting.
Releasing assigned function to the  button
1) Press as to select [FUNCTION BUTTON].
2)...

[OFF]Disables audio output in the standby mode.
[ON]Enables audio output in the standby mode when [STANDBY MODE] is set to [NORMAL]. At this time, press the  button /  button on the remote control or qw buttons on the control panel to adjust the volume.
Note
 fWhen [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO] (x page 72), even if [IN STANDBY MODE] is set to 
[ON], audio cannot be output during standby.  
Setting audio input selection
Choose the audio input terminal for each input signal.
1) Press as...

[TEST PATTERN]
Displays the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before 
performing various adjustments.
1) Press as to select [TEST PATTERN].
2) Press the  button.
 fThe test pattern with the [PATTERN CHANGE] individual adjustment screen is displayed. 
3) Press qw to switch the item.
 fThe items will switch each time you press the button. All white → Color bars → White cross on...

[SECURITY] menu
On the menu screen, select [SECURITY] from the main menu, and select an \
item from the sub-menu.Refer to "Navigating through the menu" (x page 47) for the operation of the menu screen.
 f 
When the projector is used for the first time Initial password: Press awsqawsq in order, and press the  
button.
 fAfter selecting the item, press asqw to set.
 
Attention
 fWhen you select the [SECURITY] menu and press the  button, entering a password is required. Enter the preset password and...

Note
 fThe entered password is displayed with "" mark on the screen.
 fAn error message is displayed on the screen when the entered password is\
 incorrect. Re-enter the correct password. fIf numbers have been used for the security password, the security password will need to be initialized again if the remote 
control is lost. Consult your dealer for the initialization method.
[TEXT DISPLAY]
Overlap the security message (text) over the projecting image.
1) Press as to select [TEXT DISPLAY].
2)...

[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote control.
1) Press as to select [CONTROL DEVICE SETUP].
2) Press the  button.
 fThe [CONTROL DEVICE SETUP] screen is displayed.
3) Press as to select one item between [CONTROL PANEL] and [REMOTE CONTROLLER].
[CONTROL PANEL]You can set the limitation on the control from the control panel.
[REMOTE CONTROLLER]You can set the limitation on the control from the remote control.
4) Press qw to switch between [ENABLE]...

[NETWORK] menu
On the menu screen, select [NETWORK] from the main menu, and select an i\
tem from the sub-menu.Refer to "Navigating through the menu" (x page 47) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.
[WIRED LAN]
You can make detailed wired LAN settings.
1) Press as to select [WIRED LAN].
2) Press the  button.
 fThe [WIRED DETAILED SETUP] screen is displayed.
3) Press as to select an item, and change the setting according to the instructions\
.
[DHCP]...

[NAME CHANGE]
You can change the projector name, for example, when using the DHCP server.
1) Press as to select [NAME CHANGE].
2) Press the  button.
 fThe [NAME CHANGE] screen is displayed.
3) Select characters with the asqw buttons and press the  button to enter the projector name. 
 fSelect [ALL DELETE] to delete all the entered characters, or press the  button on the remote control to 
delete a character on the cursor in the entry field.
4) Select [OK] with the as buttons and press the  button. 
 fTo...