Panasonic LCD Projector Pt Vw350 Operating Instructions

 terminal pin assignments and signal names
Outside viewPin No.Signal namesPin No.Signal names
R/PR*1+5 V
G/Y*1GND
B/PB*1—
—DDC data
GNDHD/SYNC
GNDVD
GNDDDC clock
GND
*1: It is only for RGB signals when the terminal is used as the input terminal. 
 terminal pin assignments and signal names
Outside viewPin No.Signal namesPin No.Signal names
T.M.D.S data 2+T.M.D.S clock shield
T.M.D.S data 2 shieldT.M.D.S clock -
T.M.D.S data 2-CEC
T.M.D.S data 1+—
T.M.D.S data 1 shieldSCL
T.M.D.S data 1-SDA
T.M.D.S data...

Connecting example : AV equipment
For // terminals
Attention
 fAlways use one of the following when connecting a VCR. 
- A VCR with built-in time base corrector (TBC). 
- A time base corrector (TBC) between the projector and the VCR.
 fIf nonstandard burst signals are connected, the image may be distorted. \
In such case, connect the time base corrector 
(TBC) between the projector and the external devices.
Note
 fFor an HDMI cable, use an HDMI High Speed cable that conforms to HDMI standards. If a cable...

Attention
 fWhen connecting the projector to a computer or an external device, use the power cord supplied with each device and 
commercially available shielded cables.
Note
 fIf you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume 
feature to operate the projector.
Connecting example : Audio
Note
 fIf the [AUDIO IN SELECT] settings are incorrect, the projector may have malfunctions such as the absence of audio.  
(x page 74)
 fWhen the...

Chapter 3   Basic Operations
This chapter describes basic operations to start with.
34 - ENGLISH  

Powering on/off
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed 
easily.
For details of power cord handling, refer to “Read this first!” (x page 2).
Attaching 
1) Check the shapes of the  terminal on the back of the projector bo\
dy and the power cord 
connector and insert the plug completely in the correct direction (unti\
l you hear the side tabs click in 
place).
Removing
1) Confirm that the projector is in...

Indicator statusStatus
Green
LitProjecting.
Blinking
The power is on and the lamp is not working. The [PROJECTOR SETUP] menu x [ECO 
MANAGEMENT] x [POWER MANAGEMENT] is set to [READY].*3
The lamp starts work. The projector will project image after a while.*4
*1: The indicator will light as the following order:
2.75 seconds (light) → 0.25 seconds (off) → 0.75 seconds (light) → 0.25 seconds (off)
*2: The indicator will light as the following order:
2.75 seconds (light) → 0.25 seconds (off)
*3: The...

1) Press asqw to select the display language. 
2) Press the  button to proceed to the initial setting.
Initial setting (installation setting)
Set each item.
 
1) Press as to select an item.
ItemDescriptionPage
[PROJECTION METHOD] Set [PROJECTION METHOD] depending on the installation mode.  After completed the initial setting, you can change the setting from the [PRO-JECTOR SETUP] menu → [PROJECTION METHOD].70
[SCREEN FORMAT]*1 Set the screen format (aspect ratio) and display position of the image. After...

Initial setting (standby mode)
ItemDescriptionPage
[STANDBY MODE] 
Set the operation mode during standby. 
 f 
The default setting is [ECO] that keeps power consumption low during 
standby.
 f 
Set to [NORMAL] to use the network function or the serial communication 
function during standby. 
 f 
Set to [NETWORK] to reduce power consumption during standby, and to 
operate the projector via the wired LAN or the serial communication func\
tion 
by using the Wake on LAN function.After completed the initial...

6) Adjust the size of the image to match the screen with the zoom ring.
7) Adjust the focus with the focus ring.
Note
 fWhen the projector is switched on for the first time after purchase as well as when the [PROJECTOR SETUP] menu → [INITIALIZE ALL] is executed, the initial setting screen is displayed after projection starts.
Powering Off the Projector
1) Press the power  button on the control panel or on the remote control.
 fThe following message appears.
2) Press qw to select [OK], and press the...

Projecting
Check the connections of the peripheral devices (x page 30) and connection of the power cord (x page 34) and switch on the power (x page 36) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
1) Press the , , ,  or  butto\
n on the remote control or 
 button on the control panel.
 fThe image of the signal being input in the selected terminal is projecte\
d.
 fYou can check the input source through [DETAILED] / [SIMPLE]...