Panasonic LCD Projector Pt Vw350 Operating Instructions

[PICTURE] menu
On the menu screen, select [PICTURE] from the main menu, and select an i\
tem from the sub-menu.Refer to "Navigating through the menu" (x page 47) for the operation of the menu screen.After selecting the item, press asqw to set.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press as to select [PICTURE MODE]. 
2) Press qw or the  button.
 fThe [PICTURE MODE] individual adjustment screen...

[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1) Press as to select [BRIGHTNESS].
2) Press qw or the  button.
 fThe [BRIGHTNESS] individual adjustment screen is displayed.
3) Press qw to adjust the level.
OperationAdjustmentAdjustment range
Press the ► button.Increases the brightness of the dark (black) parts of the screen.-32 ~ +32Press the ◄ button.Reduces the brightness of the dark (black) parts of the screen.
[COLOR]
(Only for movie-based signal input)
You can adjust the...

[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
1) Press as to select [COLOR TEMPERATURE].
2) Press qw or the  button.
 fThe [COLOR TEMPERATURE] individual adjustment screen is displayed.
3) Press qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT]Factory default setting.
[HIGH]Becomes a bluish image. Select this when the white areas of the projecte\
d image are reddish.
[LOW]Becomes a reddish...

3) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO]Enables auto correction of [DAYLIGHT VIEW]. The brightness of the room is detected by the luminance sensor, and the vividness of the image is automatically corrected.  
[ON]Enables [DAYLIGHT VIEW].
[OFF]Disables [DAYLIGHT VIEW].
Note
 f[DAYLIGHT VIEW] cannot be set to [AUTO] when the [PROJECTOR SETUP] menu → [PROJECTION METHOD] is set to 
[REAR/DESK] or [REAR/CEILING].
 fThe [AUTO] mode may not function properly...

[RGB/YPBPR]/[RGB/YCBCR]
Set it to [AUTO] normally. If images are not displayed correctly when this is set to [AUTO], set either [RGB], [YCBCR] or [YPBPR] in accordance with the input signal.
1) Press as to select [RGB/YPBPR] or [RGB/YCBCR].
2) Press qw or the  button.
 fThe [RGB/YPBPR] or [RGB/YCBCR] individual adjustment screen is displayed.
3) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO]The sync signal automatically selects the signal [RGB]/...

[POSITION] menu
On the menu screen, select [POSITION] from the main menu, and select an \
item from the sub-menu.Refer to "Navigating through the menu" (x page 47) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.
[REALTIME KEYSTONE]
The projector can correct the vertical trapezoidal distortion automatically when the projector is installed tilted.
1) Press as to select [REALTIME KEYSTONE].
2) Press qw or the  button.
 f[REALTIME KEYSTONE] individual adjustment...

4) Press the  button.
 fThe [KEYSTONE] individual adjustment screen is displayed.
5) Press asqw to adjust the item.
ItemsOperationAdjustmentAdjustment range
[H]
Press the w button.Adjusts the right of the keystone.
-60 ~ +60
Press the q button.Adjusts the left of the keystone.
[V]
Press the a button.Adjusts the upper of the keystone.
-80 ~ +80
Press the s button.Adjusts the bottom of the keystone.
[CORNER CORRECTION]
1) Press as to select [KEYSTONE].
2) Press the  button.
 fThe [KEYSTONE] screen is...

[SHIFT]
(Only for computer signal input)
Move the image position vertically or horizontally if the image position projected on the screen is shifted even when the relative 
position of the projector and the screen is installed correctly.
1) Press as to select [SHIFT].
2) Press the  button.
 fThe [SHIFT] screen is displayed.
3) Press asqw to adjust the position.
OrientationOperationAdjustment
Vertical (up and down) 
adjustment.
Press the a button.The image position moves up.
Press the s button.The image...

3) Press qw to adjust the value.
 fThe adjustment values are [-16] to [+16]. Adjust so that the amount of interference is at a minimum.
Note
 fCertain signals may not be adjustable. fOptimal value may not be achieved if the output from the input computer is unstable. fTo project a signal with dot clock frequency with 162 MHz or higher, noise may not disappear even if [CLOCK PHASE] is adjusted. f[CLOCK PHASE] cannot be adjusted when a digital signal is input. 
[OVER SCAN]
Use this function when characters...

Note
 fThe image size may be switched abnormally when [AUTO] is selected, please set to [NORMAL] or [WIDE] according to the input signal. fSome size modes are not available for certain types of input signals.  fIf an aspect ratio which is different from the aspect ratio for the input signals is selected, the imag\
es will appear differently from the originals. Be careful of this when selecting the aspect ratio. fIf using the projector in places such as cafes or hotels to display prog\
rams for a...