Panasonic LCD Projector Pt Rz670 Operating Instructions

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 51
Switching on/off the projector
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
Confirm that the  switch is on the  side before connecting the power cord.
For details of power cord handling, refer to “Read this first!” ( x page 2).
How to attach the power cord
1) Check the shapes of the  terminal on the side of the projector and the...

Chapter 3 Basic Operations — Switching on/off the projector
52 - ENGLISH
Note
 fWhile the power indicator  is lit in orange, the fan is running to cool the projector. fFor approximately five seconds after the projector is switched of f, the indicator does not light up even if the power is switched on.  After the 
power indicator  lights in red, turn on the power again.
 fThe projector consumes power even in standby mode (power indicator  lit in red). Refer to “Power consumption” 
(x
  page   178) for the...

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 53
1) Press asqw to adjust the focus.
LENS
FOCUS
ADJUST
2) Press the  button to proceed to the initial setting.
Initial setting (display language)
Select the language to show on the screen. 
After completed the initial setting, you can change the display language from the [DISPLA Y LANGUAGE] menu.
1) Press as to select the display language.
ENTER
1/7
Please select DISPLAY LANGUAGE.
INITIAL SETTING
SELECT
SET
2) Press the  button to...

Chapter 3 Basic Operations — Switching on/off the projector
54 - ENGLISH
[NORMAL]Set this item when high luminance is required. The estimated runtime is approximately 20   000 hours.
[ECO] Although the luminance is lower than that of [NORMAL], set this item to increase the life of the light 
source. The estimated runtime is approximately 24
  000 hours.
[LONG LIFE1] Although the luminance is lower than that of [ECO], set this item to increase the life of the light 
source. The estimated runtime is...

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 55
 fWhen the cursor is moved from [CALIBRA TION TIME] using as, [CALIBRATION TIME] is fixed.
 fBrightness and color are measured at the specified time. 

The dynamic contrast function does not operate during measurement.
 fWhen not specifying the time, press  as

 to select [CALIBRATION TIME] (the state where the time is not blinking), and press the 
 button.
13) Press  as to select [CALIBRATION MESSAGE].
14)  
Press 
 qw to switch...

Chapter 3 Basic Operations — Switching on/off the projector
56 - ENGLISH
Initial setting (installation setting)
Set [PROJECTION METHOD] and [COOLING CONDITION] depending on the installation mode. Refer to “Installation mode” (x   page   30) 
for details.
Set [HIGH ALTITUDE MODE] to [OVER 2700m] when using the projector at high altitudes between 2
  700   m (8   858') and 4   200   m (13   780') 
above sea level.
After completed the initial setting, you can change the settings of each item from...

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 57
Initial setting (screen setting)
Set the screen format (aspect ratio) and display position of the image. After completed the initial setting, you can change the settings of each 
item from the [DISPLAY OPTION] menu → [SCREEN SETTING].
1) Press  as to select an item.
2)  
Press 
 qw to switch the setting.
16:105/7
SCREEN POSITION
Set as necessary for the screen in use.
INITIAL SETTING
SET CHANGE
MENU SELECTSCREEN FORMAT
ENTER
3)...

Chapter 3 Basic Operations — Switching on/off the projector
58 - ENGLISH
Initial setting (date and time)
Set the local date and time. After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu → [DATE 
AND TIME].
To set the date and time automatically, refer to “Setting the date and time automatically” (x
  page   123).
1) Press as to select an item.
20XX7/7
11123456
MONTH
D AY
HOUR
MINUTE
SECOND
Please set the date and time of the built-in clock of the 
projector....

Chapter 3 Basic Operations — Switching on/off the projector
ENGLISH - 59
Note
 fWhen the projector is switched on for the first time after purchase, as well as when [ALL  USER DA TA] is executed from the [PROJECTOR 
SETUP] menu → [INITIALIZE], the focus adjustment screen is displayed after projection starts, then the [INITIAL  SETTING] screen is 
displayed. Refer to “When the initial setting screen is displayed” ( x
  page   52) for details.
Switching off the projector
1)
2)
1)
4)
3)
2)
1) Press the...

Chapter 3 Basic Operations — Projecting
60 - ENGLISH
Projecting
Check the projection lens attachment (x   page   44), external device connection (x   page   46), power cord connection (x   page   51), 
switch on the power ( x
  page   52) to start projecting. Select the video for projection, and adjust appearance of the projected image.
Selecting the input signal
Select an input signal.
1) Press the input selection ( and , or , , , , 
, ) button on the remote control or the control panel.
(SDI input is...