Panasonic LCD Projector Pt Rz670 Operating Instructions

Chapter 1 Preparation — Precautions for use
ENGLISH - 21
Early Warning Software
The projector supports “Early Warning Software” which notifies of abnormality and detects signs of possible abnormality by 
monitoring the status of equipment (projectors or flat-panel displays) inside an intranet. Because this software gives notification 
of approximate time to replace consumables and parts, and to clean each part, equipment maintenance can be performed in 
advance.
Depending on the type of license, the...

Chapter 1 Preparation — Precautions for use
22 - ENGLISH
 rComputer and external device connections
 fWhen connecting a computer or an external device, read this manual carefully regarding the use of power cords and 
shielded cables as well.
Accessories
Make sure that the following accessories are provided with your projector . Numbers enclosed in <    > show the number of 
accessories.
Wireless/wired remote control unit 
(N2QAYA000060)
Power cord 
(TXFSX03VBDZ)
(TXFSX02VBDZ)
(TXFSX03VARZ)
(TXFSX02UTRZ)...

Chapter 1 Preparation — Precautions for use
ENGLISH - 23
Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follows.
Instruction/list (PDF) Operating Instructions – Functional ManualMulti Projector Monitoring & Control Software Operating Instructions
Logo Transfer Software Operating Instructions
List of Compatible Projector 
ModelsThis is a list of projectors that are compatible with the software 
contained in the CD-ROM and their restrictions.
Software Multi Projector Monitoring...

Chapter 1 Preparation — About your projector
24 - ENGLISH
About your projector
Remote control
1
3 2
4
5
7 6
8
9
10 15 12 11
13
14 16
17
Front To p
Bottom
1 Power standby  button
Sets the projector to the state where the projector is switched 
off (standby mode) when the  switch on the 
projector is set to  and in projection mode.
2
 
Power on < b

> button
Starts projection when the  switch on the 
projector is set to  when the power is switched off 
(standby mode).
3
 
Remote control indicator
Blinks if...

Chapter 1 Preparation — About your projector
ENGLISH - 25
 fThe operation of the  button is disabled in the factory default settings.  The operation is enabled when [REMOTE CONTROL] is set 
to [USER] and [VIDEO BUTT ON] of [INPUT SELECT BUTTON] is set to other than [DISABLE], from the [SECURITY] menu  → [CONTROL 
DEVICE SETUP] (x
  page   132).
Projector body
1 2 3 4 5 6
7 7
10
88
11
9
16 17
14
13 15
777
Front Side
Rear
8
88
12
Projection direction
Bottom
1 Remote control signal receiver (front)
2...

Chapter 1 Preparation — About your projector
26 - ENGLISH
 rControl panel
9
10
11
12
13
14
2
4 3 1
5
6
7
8
1 Power on <
b > button
Starts projection when the  switch on the 
projector is set to  when the power is switched off 
(standby mode).
2
 
Power standby <
 v> button
Sets the projector to the state where the projector is switched 
off (standby mode) when the  switch on the 
projector is set to  and in projection mode.
3
 
 button
Switches the input to RGB1.
4

 
 button
Switches the input to RGB2....

Chapter 1 Preparation — Preparing the remote control
ENGLISH - 27
Preparing the remote control
Inserting and removing the batteries
(ii)(i)
Fig. 1Fig. 2
1) Open the cover. (Fig. 1)
2)  
Insert the batteries and close the cover (insert the 
 m side first). (Fig. 2)
 fWhen removing the batteries, perform the steps in reverse order .
When using the multiple projectors
When you use the multiple projectors together, you can control all the projectors simultaneously or each projector in\
dividually using...

Chapter 1 Preparation — Preparing the remote control
28 - ENGLISH
Connecting the remote control to the projector with a cable
When you use the system with multiple projectors, use commercially available M3 stereo mini jack cables and connect the other devices to the 
/ terminals of the projector.
The remote control is effective even in places where an obstacle stands in the light path or whe\
re devices are susceptible to outside light.
Connecting terminalsConnecting to a second projector
M3 stereo mini...

ENGLISH - 29
Chapter 2 Getting Started
This chapter describes things you need to do before using the projector \
such as the setup and connections.  

Chapter 2 Getting Started — Setting up
30 - ENGLISH
Setting up
Installation mode
There are six ways to set up the projector. Set the [PROJECTOR SETUP] menu → [PROJECTION METHOD] (x   page   107) depending on 
the installation mode. Set [COOLING CONDITION] to [AUTO]. Using the projector with [COOLING CONDITION] set incorrectly may shorten 
the life of the light source.
Mounting on the ceiling and projecting forward Setting on a desk/floor and projecting from rear
(Using the translucent screen)
Menu...