Panasonic LCD Projector Pt Lw330 Operating Instructions
Here you can view all the pages of manual Panasonic LCD Projector Pt Lw330 Operating Instructions. The Panasonic manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
ENGLISH - 31 terminal pin assignments and signal names Outside viewPin No.Signal names Pin No.Signal names T.M.D.S data 2+T.M.D.S clock shield T.M.D.S data 2 shieldT.M.D.S clock - T.M.D.S data 2-CEC T.M.D.S data 1+— T.M.D.S data 1 shieldSCL T.M.D.S data 1-SDA T.M.D.S data 0+DDC/CEC GND T.M.D.S data 0 shield+5V T.M.D.S data 0-Hot plug detection T.M.D.S clock + Connecting example : AV equipment Attention f Always use one of the following when connecting a VCR. - A VCR with built-in time base corrector...
Page 32
32 - ENGLISH r For PT-LW330, PT-LW280, PT-LB360 and PT-LB330 r For PT-LB300 and PT-LB280 Attention f When connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially available shielded cables. Note f If you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume feature to operate the projector. f When the terminal is connected with cable, the sound will not be output from...
Page 33
ENGLISH - 33 Chapter 3 Basic Operations This chapter describes basic operations to start with.
Page 34
![Page 34
34 - ENGLISH
Powering on/off
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
For details of power cord handling, refer to “Read this first!” ( x page 2).
Attaching
1) Check the shapes of the terminal on the back of the projector bo\
dy and the power cord
connector and insert the plug completely in the correct direction.
Removing
1) Confirm that the projector is in standby mode, and remove the power plug\...](http://img.usermanuals.tech/thumb/58/75982/w300_pt-lw330_en_om_d-33.png "Page 34
34 - ENGLISH
Powering on/off
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
For details of power cord handling, refer to “Read this first!” ( x page 2).
Attaching
1) Check the shapes of the terminal on the back of the projector bo\
dy and the power cord
connector and insert the plug completely in the correct direction.
Removing
1) Confirm that the projector is in standby mode, and remove the power plug\...")
34 - ENGLISH Powering on/off Connecting the power cord Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily. For details of power cord handling, refer to “Read this first!” ( x page 2). Attaching 1) Check the shapes of the terminal on the back of the projector bo\ dy and the power cord connector and insert the plug completely in the correct direction. Removing 1) Confirm that the projector is in standby mode, and remove the power plug\...
Page 35
ENGLISH - 35 Powering On the Projector Before switching on the projector, make sure all the other devices are correctly connected. (Æ pages 30 - 32) 2)1) 3) 3) 1) Connect the power cord to the projector body. 2) Connect the power plug to an outlet. f The power indicator lights in red, and the projector will enter the standby mode. 3) Press the power button on the control panel or on the remote control. f The power indicator blinks in red, after a while the indicator lights in green. f The...
Page 36
![Page 36
36 - ENGLISH
Making adjustments and selections
It is recommended that images are projected continuously for at least 30\
minutes before the focus is adjusted.
3)
5)
3)
1) Adjust the focus of the image roughly. (x page 37)
2) Change the settings of the [Display] menu → [Project way] depending on the installation mode.
(x page 51)
f Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen.
3) Press the button on the control panel or the input selecti\
on (,
, , , )...](http://img.usermanuals.tech/thumb/58/75982/w300_pt-lw330_en_om_d-35.png "Page 36
36 - ENGLISH
Making adjustments and selections
It is recommended that images are projected continuously for at least 30\
minutes before the focus is adjusted.
3)
5)
3)
1) Adjust the focus of the image roughly. (x page 37)
2) Change the settings of the [Display] menu → [Project way] depending on the installation mode.
(x page 51)
f Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen.
3) Press the button on the control panel or the input selecti\
on (,
, , , )...")
36 - ENGLISH Making adjustments and selections It is recommended that images are projected continuously for at least 30\ minutes before the focus is adjusted. 3) 5) 3) 1) Adjust the focus of the image roughly. (x page 37) 2) Change the settings of the [Display] menu → [Project way] depending on the installation mode. (x page 51) f Refer to “Navigating through the menu” ( x page 44) for the operation of the menu screen. 3) Press the button on the control panel or the input selecti\ on (, , , , )...
Page 37
![Page 37
ENGLISH - 37
Projecting
Check the connections of the peripheral devices (Æ pages 30 - 32) and connection of the power cord (x page 34) and
switch on the power ( x page 35) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
1) Press the button on the control panel or the input selecti\
on (, ,
, or ) buttons on the remote control.
f The button is only for PT-LW330, PT-LW280, PT-LB360 and PT-LB330.
f The image of the...](http://img.usermanuals.tech/thumb/58/75982/w300_pt-lw330_en_om_d-36.png "Page 37
ENGLISH - 37
Projecting
Check the connections of the peripheral devices (Æ pages 30 - 32) and connection of the power cord (x page 34) and
switch on the power ( x page 35) to start the projector. Select the image and adjust the state of the image.
Selecting the input signal
Select an input signal.
1) Press the button on the control panel or the input selecti\
on (, ,
, or ) buttons on the remote control.
f The button is only for PT-LW330, PT-LW280, PT-LB360 and PT-LB330.
f The image of the...")
ENGLISH - 37 Projecting Check the connections of the peripheral devices (Æ pages 30 - 32) and connection of the power cord (x page 34) and switch on the power ( x page 35) to start the projector. Select the image and adjust the state of the image. Selecting the input signal Select an input signal. 1) Press the button on the control panel or the input selecti\ on (, , , or ) buttons on the remote control. f The button is only for PT-LW330, PT-LW280, PT-LB360 and PT-LB330. f The image of the...
Page 38
![Page 38
38 - ENGLISH
Basic operations by using the remote control
Using the automatic setup function
Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time.
The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when
analog RGB signals consisting of bitmap images such as computer signals \
are being input. Supplying images with bright white
borders at the edges and high-contrast...](http://img.usermanuals.tech/thumb/58/75982/w300_pt-lw330_en_om_d-37.png "Page 38
38 - ENGLISH
Basic operations by using the remote control
Using the automatic setup function
Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time.
The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when
analog RGB signals consisting of bitmap images such as computer signals \
are being input. Supplying images with bright white
borders at the edges and high-contrast...")
38 - ENGLISH Basic operations by using the remote control Using the automatic setup function Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time. The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals \ are being input. Supplying images with bright white borders at the edges and high-contrast...
Page 39
![Page 39
ENGLISH - 39
Note
f For more details about Memory Viewer function, refer to “Memory Viewer function” ( x page 79).
f For more details about USB Display function, refer to “USB Display function” ( x page 81).
Switching the aspect ratio of the image
You can switch aspect ratios according to the input signal.
button
1) Press the button on the remote control.
Note
f For more details, refer to the [Display] menu → [Aspect] (x page 50).
Using the keystone distortion and curved correction functions
You...](http://img.usermanuals.tech/thumb/58/75982/w300_pt-lw330_en_om_d-38.png "Page 39
ENGLISH - 39
Note
f For more details about Memory Viewer function, refer to “Memory Viewer function” ( x page 79).
f For more details about USB Display function, refer to “USB Display function” ( x page 81).
Switching the aspect ratio of the image
You can switch aspect ratios according to the input signal.
button
1) Press the button on the remote control.
Note
f For more details, refer to the [Display] menu → [Aspect] (x page 50).
Using the keystone distortion and curved correction functions
You...")
ENGLISH - 39 Note f For more details about Memory Viewer function, refer to “Memory Viewer function” ( x page 79). f For more details about USB Display function, refer to “USB Display function” ( x page 81). Switching the aspect ratio of the image You can switch aspect ratios according to the input signal. button 1) Press the button on the remote control. Note f For more details, refer to the [Display] menu → [Aspect] (x page 50). Using the keystone distortion and curved correction functions You...
Page 40
![Page 40
40 - ENGLISH
Using the information function
This function allows you to display the status of the projector.
INFO.
button
1) Press the button on the remote control.
f The [Info.] screen is displayed.
f When the [Info.] screen is recalled by using button on the remote control, the on-screen menu cannot be
operated.
2) Press the button again.
f The [Info.] screen disappears.
Note
f For more details, refer to the [Info.] menu (x page 73).
Using the freeze function
You can freeze the projected...](http://img.usermanuals.tech/thumb/58/75982/w300_pt-lw330_en_om_d-39.png "Page 40
40 - ENGLISH
Using the information function
This function allows you to display the status of the projector.
INFO.
button
1) Press the button on the remote control.
f The [Info.] screen is displayed.
f When the [Info.] screen is recalled by using button on the remote control, the on-screen menu cannot be
operated.
2) Press the button again.
f The [Info.] screen disappears.
Note
f For more details, refer to the [Info.] menu (x page 73).
Using the freeze function
You can freeze the projected...")
40 - ENGLISH Using the information function This function allows you to display the status of the projector. INFO. button 1) Press the button on the remote control. f The [Info.] screen is displayed. f When the [Info.] screen is recalled by using button on the remote control, the on-screen menu cannot be operated. 2) Press the button again. f The [Info.] screen disappears. Note f For more details, refer to the [Info.] menu (x page 73). Using the freeze function You can freeze the projected...