Panasonic LCD Projector Pt Lw330 Operating Instructions
Here you can view all the pages of manual Panasonic LCD Projector Pt Lw330 Operating Instructions. The Panasonic manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 81
ENGLISH - 81 Note f PDF display is switched at intervals. Please do not perform continuous operations during a short period of time. Termination of the Memory Viewer 1) Press asqw to select the thumbnail which is displayed on the upper left corner. 2) Press the button on the remote control. f Return to the standby screen “please press RC ENTER”. 3) Remove the USB memory directly. Attention f When inserting the USB memory, confirm the direction of the plug not to damage the terminal. f...
Page 82
82 - ENGLISH [Active audio] / [Disable audio]Set whether to output the audio from the computer. [Play video] / [Pause video] Switch between play and pause the image. [Start] / [Stop] Set whether to display the image from the computer. [Exit] Displayed in gray and cannot be selected. Note f It will take a while when you want to project the computer screen. f Connect a USB cable directly to the USB connector of a computer. It will not work when connect through a USB hub. f The screen resolution of...
Page 83
ENGLISH - 83 Chapter 5 Maintenance This chapter describes methods of inspection when there are problems, ma\ intenance, and replacement of the units.
Page 84
84 - ENGLISH Power/Warning Indicators When an indicator lights up If a problem should occur inside the projector, the power indicator and the warning indicator will inform you by lighting or blinking. Check the status of the indicators and remedy the indicated problems as follows. Attention f Before you take a remedial measure, follow the procedure of switching the power of f indicated in “Powering Off the Projector” (x page 36). Power indica - tor Warning indicator Status CauseSolution...
Page 85
ENGLISH - 85 Power indica- tor Warning indicator Status CauseSolution GreenLighting OffProjecting. ---- Lighting Lighting in red The replacement time of the lamp unit is displayed. (Pro - jecting) f Is the lamp replacement warning icon displayed when turn on or turn off the projector? f The indicator lights up when the usage time of the lamp unit reaches 6 000 hours (when [Lamp control] is set to [ (Eco 1)]). f Replace the lamp unit. Lighting Blinking in red It has exceed the...
Page 86
86 - ENGLISH Maintenance/replacement Before performing maintenance/replacement f When you perform maintenance or replacement of the parts, make sure to turn of f the power and disconnect the power plug from the wall outlet. (x page 36) f Be sure to observe the procedure “Powering Off the Projector” (x page 36) when performing power supply operation. Maintenance Outer Case Wipe off dirt and dust using a soft dry cloth. f If the dirt is persistent, soak the cloth with water and wring it thorou\ ghly...
Page 87
ENGLISH - 87 Cleaning the air filter unit Remove the air filter unit beforehand according to the previously described procedure in “Removing the air filter unit”. 1) Clean the air filter unit. f Vacuum dirt and dust from the air filter unit. f Do not wash the air filter unit. Attaching the air filter unit 1) Attach the new air filter unit to the air filter cover. f There is a distinction between the inside and outside of the air filter unit. Align the red mark on the air filter unit with the red...
Page 88
88 - ENGLISH Attention f Do not disassemble the air filter unit. f When attaching the air filter unit, make sure that the projector is stable, and work in an environment that is safe, even in the event of the air filter unit dropping. f Make sure that the air filter unit is properly attached before using the projector . If it is not attached, the projector will suck in dirt and dust causing a malfunction. Note f After cleaning the air filter, reset the filter counter. Otherwise, the warning...
Page 89
ENGLISH - 89 The displayed time in [Lamp counter] On-screen display indicator Over 5 700 hours less than 6 000 hours f The lamp replacement icon is displayed for 10 seconds. If you press any button within 10 seconds, the icon disappears. f The lamp replacement icon will display for 4 seconds on the screen after switching the input source or turning on the projector. -- Over 6 000 hours less than 6 600 hours f The lamp replacement warning icon is displayed for 10 seconds. If you...
Page 90
90 - ENGLISH f Perform step 2) in reverse direction to attach the lamp cover. Resetting the lamp counter Be sure to reset the lamp counter after replacing the lamp unit. 1) Connect the power plug, press the power < v/b> button on the control panel or on the remote control. 2) While pressing the a button on the control panel, press and hold the button on\ the control panel for 8 seconds or more. f The lamp counter will be reset to 0. (At this time, there is displaying nothing.) 3) Press the...