Panasonic Kx Tva50 Installation Manual

The available Mode Switch positions are shown in the following table. The black area in the switch illustration
indicates the direction of the switch.Switch PositionOperation0Puts the VPS in normal mode.1Reserved2Puts the VPS in DPT Integration mode. Auto Configuration starts and all ports are set
to provide Automated Attendant service.3Puts the VPS in DPT Integration mode. Auto Configuration starts and all ports are set
to provide Voice Mail service.4Reserved5Initializes the VPS. All settings are reset...

5.Connect the port cables.
6. Confirm that the  RUN indicator blinks the same number of times as the Mode Switch position (e.g., 5 blinks
for switch position 5, etc.).
• This may take several minutes. The  ALARM indicator and  RUN indicator will first blink intermittently
before the  RUN indicator blinks to indicate the Mode Switch position.
7. Turn the power switch off at the VPS.
8. Set the Mode Switch to position 0.
9. Turn the power switch back on at the VPS.42Installation ManualDocument Version  3.0...

2.4  Installation OverviewThe following is an overview of the steps needed to install optional cards and prepare the VPS hardware for
use. Once hardware installation is complete, see Section  6  Configuring the System for instructions on software
setup and VPS customization.
CAUTION
The information below is only intended as an overview of the installation process. When installing the VPS,
refer to the sections listed below for detailed instructions.
1. Open the covers (see 2.5  Opening/Closing the...

2.5  Opening/Closing the CoversThe model shown here is the KX-TVA200, however this procedure is the same for the KX-TVA50.
Opening the Covers 1.Push the release button in the direction shown below (1), and slide the cable cover in the direction shown
below (2). Turn the cable cover away from the unit and remove it.
2. Remove the 3 screws.
44Installation ManualDocument Version  3.0  2010/062.5 Opening/Closing the Covers1Release Button
Cable Cover Screw  

3.While holding both tabs located on the sides of the front cover, swing the cover open as shown.
Removing/Attaching the Front Cover
You may also detach the front cover from its hinges.
Removing the Front Cover
While holding the front cover open at a 45° angle, lift the cover away from the unit as shown.
Document Version  3.0  2010/06Installation Manual452.5 Opening/Closing the Covers   

Attaching the Front Cover
Fit the front cover to the main unit as shown below, then close the front cover.
Closing the Covers
1.Close the front cover, then tighten the 3 screws.
46Installation ManualDocument Version  3.0  2010/062.5 Opening/Closing the Covers Screw  

2.Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so that the
front hooks fit in place.
3. Slide the cable cover down until it locks.
Document Version  3.0  2010/06Installation Manual472.5 Opening/Closing the Covers   

2.6  Removing the Dummy Cover PlatesBefore installing optional cards, cut and remove the appropriate dummy cover plates from the main unit using
cutting pliers, as shown below.
The model shown here is the KX-TVA200, however this procedure is the same for the KX-TVA50.
CAUTION
For safety reasons, smooth the cut edges after removing the dummy cover plates.
48Installation ManualDocument Version  3.0  2010/062.6 Removing the Dummy Cover PlatesDummy Cover Plate  

2.7  Installing Optional Cards—KX-TVA50The KX-TVA50 can be expanded by installing the following optional cards.ModelModel NameMaximum QuantityKX-TVA5022-Port Hybrid Expansion Card2KX-TVA5032-Port Digital Expansion Card2KX-TVA524Memory Expansion Card1KX-TVA594LAN Interface Card1KX-TVA296Modem Card1
CAUTIONBefore installing optional cards, it is very important that the power to the unit be turned off. Before
touching the optional cards or any components within the unit, discharge any static electricity...

2.7.1  2-Port Hybrid Expansion Card (KX-TVA502)Each KX-TVA502 adds 2 ports to the VPS which can be used for DPT, Inband, or No Integration.
KX-TVA502 cards can be installed in slots 2 and 3 of the VPS.
Note
•When using APT Integration, only the factory-installed jacks can be used.
Integration Type
Basic ConfigurationMaximum Configuration
KX-TVA502  ´ 2No. of Usable
JacksNo. of PortsNo. of UsableJacksNo. of PortsDPT Integration1*123 (1 per card) *16Inband/No Integration2266
*1
When using DPT Integration,...