Panasonic Kx Tva50 Installation Manual

SpecificationKX-TVA50KX-TVA200Weight (when all available
option cards are installed)No more than 1.7 kg (3.75 lb.)No more than 4.0 kg (8.82 lb.)Document Version  3.0  2010/06Installation Manual311.3 Specifications 

32Installation ManualDocument Version  3.0  2010/061.3 Specifications 

Section  2
Installation
This section explains how to install the VPS and its
optional cards.Document Version  3.0  2010/06Installation Manual33 

2.1  Before InstallationPlease read the following precautions before installing the VPS.
Installation Precautions The VPS should be wall-mounted. Improper placement of the system may result in malfunction, noise, or
discoloration. Avoid installing the VPS in the following places:
• in direct sunlight; in hot, cold, or humid places
• in areas where sulfuric gas can damage the equipment (e.g., areas near thermal springs, etc.)
• where shocks or vibrations are frequent or strong
• in dusty places or places...

Environmental Requirements (KX-TVA200 only)The hard disk drive is sensitive to cold, heat, dryness, humidity, shock, vibration, and magnetic fields. Please
observe the conditions specified below.
Hard Disk Drive Usage EnvironmentOperating Temperature:5 °C to 40 °C (41 °F to 104 °F)Operating Humidity:See the graph below.Shock:Under 5 GVibration:5 Hz to 22 Hz:0.0042 cm (0.020 in.) displacement; double amplitude, 1
octave per minute.23 Hz to 350 Hz: Under 0.5 GMagnetic Field:DC: 0.6 mT
to 700 kHz: 0.7 µT...

Necessary Tools (not supplied)Twisted pair 4-conductor cables are needed for connecting the VPS to the PBX. For the KX-TVA50, twisted
pair 2-conductor cables are needed if using Inband or No Integration.
A USB cable is needed when connecting the VPS to the PC that will used for programming via the KX-TVA
Maintenance Console.36Installation ManualDocument Version  3.0  2010/062.1 Before Installation 

2.2  UnpackingThe following items are included with the VPS.KX-TVA50KX-TVA200Main Unit11AC Adaptor11AC Cord11Screws (Wall Mounting)55Washers (Wall Mounting)55Cable strap11CD-ROM11Document Version  3.0  2010/06Installation Manual372.2 Unpacking 

2.3  Names and Locations
Outside/Inside View KX-TVA501.RUN  Indicator
2. ALARM  Indicator
3. Dummy Cover Plates (for Port Card Slots
2 and 3)
4. Factory-installed Jacks
5. RESET  Button
6. SHUTDOWN  Button
7. Mode Switch
8. USB Port
9. Dummy Cover Plate (for LAN Interface
Card)
10. Dummy Cover Plate (Reserved))
11. Dummy Cover Plate (for Modem Card)
12. Ground Terminal
13. DC IN
14. Power Switch1.Main Board
2. Front Cover
3. Factory-installed Flash Memory Card
4. Cable Cover38Installation ManualDocument...

KX-TVA2001.RUN  Indicator
2. ALARM  Indicator
3. Dummy Cover Plates (for Port Card
Slots 2 to 6)
4. RESET  Button
5. SHUTDOWN  Button
6. Mode Switch
7. Factory–installed Jacks
8. LAN Port
9. USB Port
10. Dummy Cover Plate (for Modem
Card)
11. Ground Terminal
12. DC IN
13. Power Switch1.Main Board
2. Front Cover
3. 3.5" Hard Disk Drive
4. Factory-installed Port Card
5. Cable CoverDocument Version  3.0  2010/06Installation Manual392.3 Names and Locations8
7
6 5
4
9
1012 11
13
3 2
1 1
23 4 5  

System ComponentsRUN Indicator
Lights during normal operation; flashes when the system is off-line and cannot receive calls.
ALARM Indicator
Flashes when a system error is detected or while the VPS is preparing to shutdown. Lights when the shutdown
procedure is complete.
RESET Button
Restarts the VPS.
Note
•Make sure the VPS is not in use before pressing the  RESET button.
SHUTDOWN Button
Initiates the shutdown procedure. When the  ALARM indicator lights after pressing the  SHUTDOWN button,
you may...