Panasonic Kx Tg9471 Operating Instructions Manual

Voice mail service
V oice mail is an automatic answering service
offered by your service provider/telephone
company. After you subscribe to this service, your
service provider/telephone company’s voice mail
system answers calls for you when you are
unavailable to answer the phone or when your line
is busy. Messages are recorded by your service
provider/telephone company, not your telephone.
Please contact your service provider/telephone
company for details of this service.
Important:
R To use the voice...

Intercom
I ntercom calls can be made:
– between the base unit and a handset
– between handsets
Note:
R If you receive an outside call while talking on the
intercom, you hear an interrupt tone (page 28).
– To answer the call with the base unit, place
the corded handset on the cradle, then lift it
again. If the speakerphone is used, press
M N
 
2 times. You can also answer the call by
pressing  MLINE 1 N or  MLINE 2 N after hanging
up the intercom.
– To answer the call with the handset, press
MOFF N, then...

4
Press  MOFF N.
R The outside call is being routed to the
destination unit. Answering a transferred call
 Base unit
L

ift the corded handset or press  M N
 
to answer
the page.  Handset
P

ress  M N
 
to answer the page. Conference calls
3
  people can establish a conference call. Conference call with 2 outside calls
W

hile you are talking with an outside caller, you
can make or answer a 2nd call on the other line,
and then combine the calls to establish a
conference call.  Base unit
1 D

uring an...

Wall mounting
T he base unit can be mounted on a wall by
changing the wall mounting adaptor’s position.
Note:
R Make sure that the wall and the fixing method
are strong enough to support the weight of the
unit. Base unit
1
T

o remove the wall mounting adaptor, push
down the release levers ( A). Remove the
adaptor ( B). 2
A 
Turn the adaptor so that the words “UP
WALL” are facing up.
B Tuck the telephone line cord inside the wall
mounting adaptor.
C  Connect the AC adaptor cord and
telephone line cord....

Error messages
Display message Cause/solution
Busy RThe called unit is in use.
ROther units are in use and the system is busy. Try again later.
R Privacy mode is on for the call you tried to join (page 17).
R The handset you are using is too far from the base unit. Move
closer and try again.
Check tel line 1
C
 heck tel line 2 R
The supplied telephone line cord has not been connected yet or
not connected properly. Check the connections (page 8).
R If you use the unit as a single-line telephone only,...

Troubleshooting
I f you still have difficulties after following the instructions in this section, disconnect the base unit’s AC
adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then
insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn on even
a
 fter installing charged batteries. R
Place the handset on the charger to turn on the handset.
The unit does not work. RM
ake sure the batteries are installed...

Making/answering calls, intercom
Problem Cause/solution
 is flashing.
RThe handset is too far from the base unit. Move closer.
RThe base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
R The handset is not registered to the base unit. Register it
(page 31).
Noise is heard, sound cuts in and out. RY
ou are using the base unit or handset in an area with high
electrical interference. Re-position the base unit and use the
handset away from sources of interference.
R Move...

Problem Cause/solution
I cannot dial the phone number
e dited in the caller list. R
The phone number you dialed might have been edited
incorrectly (for example, the long distance “1” or the area
code is missing). Edit the phone number with another
pattern (page 33).
Time on the unit has shifted. RI
ncorrect time information from incoming Caller ID changes
the time. Set the time adjustment to  “Manual ” (off)
(page 28).
The 2nd caller’s information is not
d
 isplayed during an outside call. R
In order to...

Telephone Plug-in
Problem Cause/solution
If the installer program does
n ot start automatically. R
Double click  [Setup.exe] in your CD-ROM drive folder to start
installing.
A pop-up window (Microsoft
O
 ffice Outlook contact list) is
not displayed when a call is
received. R
Caller information indication in the “Telephone Plug-in” setting is set
to “ Disable ”. Set it to “ Enable” (page 22).
R If more than 5,000 entries are stored in the contact list, pop-up
windows may not be displayed. Erase entries...

FCC and other information
50
For assistance, please visit http://www.panasonic.com/helpUseful InformationTG9471(e)_1101_ver101.pdf   502012/11/01   9:55:26This equipment complies with Part 68 of the FCC rules 
and the requirements adopted by the ACTA. On the 
bottom of this equipment is a label that contains, 
among other information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided to the 
telephone company.
L Registration No.............(found on the...