Panasonic Kx Tg762 Operating Instructions Manual

Error messages
Display message Cause/solution
Base no power
o r
No link. Re-connect
base AC adaptor.
or
No link. R
The handset has lost communication with the
base unit. Move closer to the base unit and try
again.
R Unplug the base unit’s AC adaptor to reset the
unit. Reconnect the adaptor and try again.
R The handset’s registration may have been
canceled. Re-register the handset (page 48).
R When “ No link. ” is displayed during a
power failure, place a handset on the base
unit to supply power to the...

Display message Cause/solution
Invalid RThere is no handset registered to the base
unit matching the handset number you
entered.
R The handset is not registered to the base unit.
Register the handset (page 48).
Requires subscription
t
 o Caller ID. R
You must subscribe to a Caller ID service.
Once you receive caller information after
subscribing to a Caller ID service, this
message will not be displayed.
Use rechargeable
b
 attery. R
A wrong type of battery such as Alkaline or
Manganese was inserted. Use...

Problem Cause/solution
I cannot register a cellular
p hone to the base unit. R
Depending on the compatibility of the cellular
phone, you may not be able to register it to the
base unit. Confirm that your cellular phone
supports the hands-free profile (HFP) specification.
R Confirm that the Bluetooth feature of your cellular
phone is turned on. You may need to turn this
feature on depending on your cellular phone.
R The Bluetooth technology on your cellular phone
may not be functioning normally. Turn off...

Programmable settings
Problem Cause/solution
The display is in a
l anguage I cannot read. R
Change the display language (page 18).
I cannot register a handset
t
 o a base unit. R
The maximum number of handsets (6) is already
registered to the base unit. Cancel unused
handset registrations from the base unit (page 48). Battery recharge
Problem Cause/solution
The handset beeps and/or  flashes.
R
B
attery charge is low. Fully charge the batteries
(page 11).
I fully charged the batteries,
b
 ut
–  still...

Problem Cause/solution
The handset or base unit
d oes not ring. R
The ringer volume is turned off. Adjust the ringer
volume (page 41, 43).
R When one handset is selected to ring for cellular
calls, other units do not ring. To change the
selection, see page 20.
R Silent mode is turned on for the handset. Turn it off
(page 46).
I cannot make local calls
w
 ith the handset or base
unit using a cellular line. R
You need to add your area code when making
cellular calls. Store your area code in order to...

Caller ID/Talking Caller ID
Problem Cause/solution
Caller information is not
d isplayed. R
You must subscribe to Caller ID service. Contact
your service provider/telephone company for
details.
R If your unit is connected to any additional
telephone equipment such as a Caller ID box or
cordless telephone line jack, plug the unit directly
into the wall jack.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base
unit and the telephone line jack. Contact your DSL/
ADSL...

Problem Cause/solution
I cannot dial the phone
n umber edited in the caller
list. R
The phone number you dialed might have been
edited incorrectly (for example, the long distance
“1” or the area code is missing). Edit the phone
number with another pattern (page 51).
Time on the unit has
s
 hifted. R
Incorrect time information from incoming Caller ID
changes the time. Set the time adjustment to
“Manual ” (off) (page 42).
The 2nd caller’s
i
 nformation is not displayed
during an outside call. R
In order to...

Problem Cause/solution
I cannot connect my
h eadset to the base unit. R
Confirm that your headset is turned on.
RIf your headset is already connected to another
Bluetooth device such as your cellular phone,
disconnect the headset from your cellular phone,
then perform the connecting procedure from the
base unit.
R If someone is using a cellular line, you cannot
connect the headset. There can be only one active
Bluetooth connection at a time.
R The headset has not been registered to the base
unit....

Problem Cause/solution
I cannot operate the
a nswering system. R
Someone is using the unit. Wait for the other user
to finish.
R A caller is leaving a message. Wait for the caller to
finish.
R The handset is too far from the base unit. Move
closer.
I cannot operate the
a
 nswering system remotely. R
The remote access code is not set. Set the remote
access code (page 60).
R You are entering the wrong remote access code. If
you have forgotten your remote access code,
enter the remote access code setting to...

FCC and other information
80
For assistance, please visit http://www.panasonic.com/helpUseful InformationThis equipment complies with Part 68 of the 
FCC rules and the requirements adopted by 
the ACTA. On the bottom of this equipment 
is a label that contains, among other 
information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided 
to the telephone company.
L Registration No.............(found on the 
bottom of the unit)
L Ringer Equivalence No....