Panasonic Kx Tg762 Operating Instructions Manual

R
If your cellular phone is in silent mode
with  “On (with Talking CID) ”
set, the unit announces caller
information even when Talking Caller
ID is turned off (page 43). To use the handset ringer tone
i

nstead of your cellular phone’s
ringer tone
Select  “Off ” in step 3, “Ring as cell
mode”, page 20.
To change the handset ringer tone for a
cellular line, see page 41. Auto connection to the
c

ellular phone
After registration, your cellular phone is
connected to the base unit. If you move
the cellular...

– for the base unit, press
MS
P-PHONE N instead of the line
button ( MCELL 1 N or  MCELL 2 N) set
for the cellular line selection
(page 22, 31).
(KX-TG7641 series: page 3)
R Once you set this mode, the following
features cannot be used:
– Landline features (page 45)
– Answering system (page 57)
Messages cannot be received.
However, you can only record voice
memo messages (page 60).
– Voice mail features (page 64)
R After this mode is turned on or off, the
base unit reboots.
– Bluetooth connections from...

2
Enter the new 4-digit PIN.  a M OK N
3 Enter the new 4-digit PIN again.  a
M SAVE N
4 MOFF N Changing the PIN for the second time
F

ollow step 1, “Changing the Bluetooth
PIN (Personal Identification Number)”,
page 22. Enter the current 4-digit PIN,
then continue from step 2. Deregistering Bluetooth
d

evices
A handset can cancel a registration of
another Bluetooth devices (cellular
phone or headset) that is stored to the
base unit.
1 MMENU N#134
2 Mb N: Select the desired device.  a
M SELECT N
R...

Making cellular calls
I
mportant:
R Only 1 cellular line can be used at a
time.
R Before making calls, confirm that the
CELL 1 or CELL 2 indicator lights
green (page 17).
1 Lift the handset and dial the phone
number.
RTo correct a digit, press  MCLEAR N.
2 MCELL N
R The unit starts dialing when:
– only 1 cellular phone is
registered.
– a specific line is set to make cellular calls (page 22).
Go to step 4.
3 Mb N: Select the desired cellular
phone.  a M SELECT N
4 When you finish talking, press
MOFF N or...

Pause (for PBX/long distance service
u
sers)
A pause is sometimes required when
making calls using a PBX or long
distance service. When storing a calling
card access number and/or PIN in the
phonebook, a pause is also needed
(page 38).
Example:  If you need to dial the line
access number “9” when making outside
calls with a PBX:
1 9 a  M PAUSE N
2 Dial the phone number.  a M N
N

ote:
R A 3.5 second pause is inserted each
time  MPAUSE N is pressed. Repeat as
needed to create longer pauses. Answering...

– the line is set to make
c ellular calls (page 22).
R The base unit user can take the
call by pressing  MCELL 1 N or
M CELL 2 N. (KX-TG7641 series:
page 3)
To release hold on the landline:
Press  M N
.
R A

nother handset user can take
the call by pressing  M N
.
R T

he base unit user can take the
call by pressing  MSP-PHONE N.
(KX-TG7641 series: page 3)
Note:
R If a call is kept on hold for more than 9
minutes, an alarm tone starts to
sound and the ringer indicator flashes
rapidly. After 1 additional...

cellular call,   is not displayed
e
ven though the feature is activated. Handset equalizer
T

his feature clarifies the voice of the
person you are talking to, producing a
more natural-sounding voice that is
easier to hear and understand.
1 Press  MMENU N while talking.
2 Mb N:  “Equalizer ” a  M SELECT N
3 Mb N: Select the desired setting.
4 Press  MOK N to exit.
Note:
R When this feature is activated,   is
d

isplayed while talking.
R Depending on the condition and
quality of your telephone line, this...

2
Mb N: Select the desired cellular
phone.  a M SELECT N
R The call is transferred to the
handset. Using the other line during a
c

onversation
You can handle a cellular call and a
landline call at the same time. When
another call is being received during a
conversation, the interrupt tone sounds
(page 43), and the 2nd caller’s
information is displayed if you subscribe
to Caller ID (page 49). You can
answer the 2nd call while holding the 1st
call. Making/answering a cellular call
d

uring a conversation...

R
Do not touch the handset’s charge
contacts during power back-up mode.
R If the battery level is low, the unit will
not work sufficiently during power
back-up mode. In addition, in case
handset battery power runs out, we
recommend connecting a corded-type
telephone (without AC adaptor) to the
same telephone line or to the same
telephone line jack using a Panasonic
T-adaptor (page 5). Panasonic Ni-MH battery
p

erformance (supplied batteries)
during power back-up mode
When the batteries are fully...

and use another handset for making
c
alls.
For the operation, please see
“Making a call using the redial list”,
page 24. Making a call using the shared
p

honebook
Only when 2 or more handsets are
registered to the base unit, you can
use the shared phonebook feature
during a power failure.
You should leave one handset on the
base unit for supplying the power, and
use another handset for making calls.
For the operation, please see “Finding
and calling from a phonebook entry”,
page 36. Answering calls...