Panasonic Kx Tg4031 Operating Instructions Manual

Useful Information
41For assistance, please visit http://www.panasonic.com/help
Wall mounting
Base unit
1
Lead the AC adaptor cord and 
telephone line cord through the hole 
in the wall mounting adaptor in the 
direction of the arrow.
2Tuck the telephone line cord inside 
the wall mounting adaptor (A). 
Connect the AC adaptor cord and 
telephone line cord ( B).
3Insert the hooks on the wall 
mounting adaptor into holes  1 and 
2  on the base unit.
4Adjust the adaptor to hold the base 
unit, then push it...

Useful Information
42For assistance, please visit http://www.panasonic.com/help
5Mount the unit on a wall then slide 
down to secure in place.
To remove the wall mounting adaptor
While pushing down the release levers 
(A), remove the adaptor ( B).
Charger
Drive the screws (not supplied) into the 
wall.
83 mm 
(31/4 inches)
or
102 mm 
(4 inches)
83 mm
(31/4 inches) 102 mm
(4 inches)
(120 V AC,
60 Hz)
1
2 1
2
Wall phone plate
B
AA
25.4 mm (1 inch)
Screws
(120 V AC, 60 Hz)
TG403x.book  Page 42  Wednesday,...

Useful Information
43For assistance, please visit http://www.panasonic.com/help
Error messages
If the unit detects a problem, one of the following messages is shown on the display.
Display messageCause/solution
Base no power
or
No link. Re-connect 
base AC adaptor. L
The handset has lost communication with the 
base unit. Move closer to the base unit and try 
again.
L Unplug the base unit’s AC adaptor to reset the 
unit. Reconnect the adaptor and try again.
L The handset’s registration may have been...

Useful Information
44For assistance, please visit http://www.panasonic.com/help
Troubleshooting
If you still have difficulties after following the instructions in this section, disconnect 
the base unit’s AC adaptor, then reconnect the base unit’s AC adaptor. Remove the 
batteries from the handset, and then insert the batteries into the handset again.
General use
Programmable settings
ProblemCause/solution
The handset does not turn 
on even after installing 
charged batteries. L
Place the handset on the...

Useful Information
45For assistance, please visit http://www.panasonic.com/help
Battery recharge
Making/answering calls, intercom
ProblemCause/solution
The handset beeps and/or 
)  flashes. L
Battery charge is low. Fully charge the batteries 
(page 10).
I fully charged the 
batteries, but 
– ) still flashes,
– 0 is displayed, or
– the operating time  seems to be shorter. L
Clean the battery ends ( S, T ) and the charge 
contacts with a dry cloth and charge again.
L It is time to replace the batteries...

Useful Information
46For assistance, please visit http://www.panasonic.com/help
Caller ID/Talking Caller ID
ProblemCause/solution
Caller information is not 
displayed. L
You must subscribe to Caller ID service. Contact 
your service provider/telephone company for 
details.
L If your unit is connected to any additional 
telephone equipment such as a Caller ID box or 
cordless telephone line jack, plug the unit directly 
into the wall jack.
L If you use a DSL/ADSL service, we recommend 
connecting a...

Useful Information
47For assistance, please visit http://www.panasonic.com/help
Answering systemThe 2nd caller’s 
information is not 
displayed during an 
outside call.
L
In order to use Caller ID, call waiting, or Call 
Waiting Caller ID (CWID), you must first contact 
your service provider/telephone company and 
subscribe to the desired service.
After subscribing, you may need to contact your 
service provider/telephone company again to 
activate this specific se rvice, even if you already 
subscribed...

Useful Information
48For assistance, please visit http://www.panasonic.com/help
Liquid damage
Caution:
LTo avoid permanent damage, do not use a microwave oven to speed up the drying 
process.
ProblemCause/solution
Liquid or other form of 
moisture has entered the 
handset/base unit. L
Disconnect the AC adaptor and telephone line 
cord from the base unit. Remove the batteries 
from the handset and leave to dry for at least 3 
days. After the handset/base unit are completely 
dry, reconnect the AC adaptor...

Useful Information
49For assistance, please visit http://www.panasonic.com/help
FCC and other information
This equipment complies with Part 68 of the 
FCC rules and the requirements adopted by 
the ACTA. On the bottom of this equipment 
is a label that contains, among other 
information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided 
to the telephone company.
L Registration No.............(found on the bottom of the unit)
L Ringer Equivalence No....

Useful Information
50For assistance, please visit http://www.panasonic.com/help
WHEN PROGRAMMING EMERGENCY 
NUMBERS AND(OR)  MAKING TEST 
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak  hours, such as early morning or late 
evenings.
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
interference, and...