Panasonic Kx Tg2740 Operating Instructions Manual

101
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
6
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antennas.
7
To charge the handset battery:
Place the handset on the base unit.
•The CHARGE indicator lights.
5
While keeping the adaptor held
to the base unit, slide the wall 
mounting adaptor to 
the left until it clicks 
into place.
4
Adjust the adaptor to hold the
base unit, aligning the arrow
Con the base unit with the
adaptor.
C
Arrow C
C
Bottom of...

102
Wall Mounting
To remove the wall mounting adaptor
Push up the RELEASE LEVER (#) with your thumb and slide the adaptor
to the right ($) with the tab kept up to release the lock. Remove the
adaptor.
Adding Another Phone
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Telephone Line Jack
T-Adaptor (KX-J66)Telephone
Line Cord
RELEASE...

103
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
A nickel cadmium battery that is recyclable powers the
product you have purchased. At the end of its useful life,
under various state and local laws, it is illegal to dispose of
this battery into your municipal waste stream. Please call 
1-800-8-BATTERY for information on how to recycle this
battery.
Battery will need to be replaced, even if you cleaned the charge contacts
and charged the battery fully, but after...

104
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the handset or if you need to register the
handset to a different base unit of the same model, it may be necessary to
cancel the registration.
Only one handset can be canceled at a time near the base unit.
Make sure the handset and the base unit are not being used.
1
Press (CONF/FUNCTION).
2
Scroll to “Initial setting” by pressing
Öor Ñ, and press á.
3
Scroll to “Registration” by pressing Ö
or Ñ,...

105
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the handset to the base unit or a different base unit
of the same model, you need to register it to that base unit. The handset will
be given a new extension number of that base unit. Only one handset can
be registered at a time. Make sure the base unit and the other handsets
are not being used. Registration must be completed within 1 minute.
1
Handset:Press (CONF/FUNCTION). 
2...

Display messageCause & Remedy
The battery needs to be charged. Recharge the
battery (p. 15).
The battery has been discharged. The handset
will not work. Charge the battery fully (p. 15).
The handset has lost communication with the
base unit. Walk closer to the base unit, and try
again.
• The called handset/base unit is in use.
• Both lines are in use. Wait until one of the line
indicators or the line status icons goes out.
• The Privacy mode is on for the call you tried to
join (p. 71).
• 
The unit you...

107
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Display messageCause & Remedy
• If the radio communication between the
handset and the base unit is partially impaired,
this display will be shown.
• If more than one unit is in use, such as
conducting external/internal calls or listening to
messages, you may not be able to use another
unit. Try again later.
• When you try to program with the base unit and
the handset is in the remote operation mode,
this display will be shown. Try...

108
Display messageCause & Remedy
When you tried to call another handset in the 
2-Way Radio mode;
– the handset is too far from your handset. Walk
closer to the handset.
– 
2-Way Radio mode on the handset is off (p. 74).
– The called handset is talking with another
handset in the 2-Way Radio mode.
The handset you tried to make a call has not
been registered to the base unit. Register it 
(p. 31, 105).
“Your greeting was not recorded. Record your
greeting again.” is announced. Your greeting was
not...

109
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Troubleshooting
Problem
“No link to base.
Walk closer to 
base and try 
again.” is displayed and
an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The handset and/or the
base unit does not ring.
The line status icons do not
display properly and/or the line
indicators do not light properly.
The handset display is blank.
You cannot store a name
and phone number in the
directory.
While...

110
Troubleshooting
Problem
You cannot make a call
even if there is a free line.
The unit does not display
the caller’s name and/or
phone number.
The display exits the Caller
List.
You cannot page the
handset or base unit.
You cannot answer a call
by lifting the handset off the
base unit or charger, or
pressing the dialing button
(
(0)to (9), (#)or (*)).
You cannot redial by
pressing
(PAUSE/REDIAL)
on the handset or
(REDIAL/PAUSE)on the
base unit
.
You cannot have a
conversation or listening to
messages...