Panasonic Kx Tg2382 Operating Instructions Manual

							51
Answering System
For assistance, please call: 1-800-211-PANA(7262)
To stop
operation Press (STOP).
•
To resume playback, press the  (MESSA\fE\bPLAYBACK).
• If you do not press any button for 60 seconds or if you press 
(STOP) again, the playback mode will be canceled.
Press (REPEAT).
•If you press within 5 seconds of playback, the previous
message will be played.
Press (SKIP).
During playback
To  repeat
message
To  skip
message
Erasing Messages
The unit will announce the remaining recording time after playback, if i\
t is 
less than 5 minutes. New messages cannot be recorded when:
—“ Memory full ” is heard.
—“ ” is displayed on the base unit.
—the ANSWER ON indicator flashes rapidly (only when the Answering System is on).
Erase some, or all, of the messages. We recommend you erase 
unnecessary messages after each playback.
Erasing a specific message
Press (ERASE)while the message you want to erase is being played 
(p. 50).
• A short beep will sound and the message will be erased.
• The unit will continue to play the next message.
Erasing all messages
All recorded messages, except the greeting message, can be erased at
one time.
1
Press (ERASE).
•“To erase all messages, press ERASE again ” is heard.
2
Within 5 seconds, press (ERASE)again.
•A beep sounds and “ No messages” is heard.
• The base unit display shows “0”.
• The information in the Caller List will not be erased. To erase Caller L\
ist 
information, see page 36.
FULL 
						

							52
Voice menu
If no commands are entered after doing steps 1 and 2, or if no commands 
are entered after you heard new or all messages and “End of final 
message”,
the following voice menu will be heard through the handset.
“ Press 4 to play back new messages. Press 5 to play back all messages. ”
•You can enter direct commands even if the voice menu has started.
Remote Operation with the Handset
You can access the Answering System
from your handset and listen to
messages. 
If new messages have been recorded, 
“New message ” will be displayed.
To listen to messages
1
Press (MUTE/FUNCTION).
2
Scroll to “Message play”by pressing Öor
Ñ, and press á.
•A beep sounds. 
• The number of new messages will be announced 
from the speaker.
To switch to the receiver, press  . 
To switch back to the speaker, press  .
• To play new messages , press (4).
• You can enter the desired direct commandsfor other functions (p. 53).
• If you do not enter a command, the voice menu will start (see below).
• After the voice menu, all message playback will start.
3
To end remote operation, press (OFF).
•To adjust the speaker or receiver volume, press  Ñto increase and press  Öto
decrease.
• After listening to new messages, 
“New message ” will disappear.
Concerning new message indications on the base unit, see page 50.
(MUTE/FUNCTION)
(OFF)
Save directory
HMessage play
Ringer setting
4:New messages 
5:All messages
IRepeat SkipH
New message [1] 
Received calls
G
Handset off the base unit 
						

							53
Answering System
For assistance, please call: 1-800-211-PANA(7262)For assistance, please call: 1-800-211-PANA(7262)
•
The unit will announce the remaining recording time after playback, if i\
t is less 
than 5 minutes.
• If a call is being received during the remote operation, you will hear i\
ncoming
call tones (p. 48). To answer the call, press  or  .
• If you hear “ Memory full” after playback, erase some, or all, of the messages
(see below).
Direct commands
NEW MESSAGE PLAYBACK 
• Only new messages are
played back.
ALL MESSAGE PLAYBACK
• All messages are played back.
REPEAT (During playback)
• The current message is
repeated.
• If you press within 5 seconds
of playback, the previous
message will be played.
• You can also press  Üto
repeat a message.
SKIP (During playback)
• The current message is
skipped. The next message is
played.
• You can also press  áto skip
a message.
STOP
• Operation is stopped
temporarily.
• To resume operation, enter a
direct command within 15
seconds, or the voice menu
will start (p. 52).(4) 
(5) 
(1) 
(2) 
(9)
ERASING A SPECIFIC  
MESSAGE 
(During playback)
•The current message is
erased.
• A short beep will sound
and the next message will
be played.
ERASING ALL MESSAGES
•All recorded messages are
erased.
• A long beep sounds, and
“No messages ” is heard.
ANSWERING SYSTEM OFF
•“Answer off ” is heard and
the Answering System is
turned off.
ANSWERING SYSTEM ON
• “Answer set ” is heard and
the Answering System is
turned on.
(*)(4) 
(*)(5)
(0) 
(8) 
						

							54
Remote Operation from a Touch Tone Phone
You can operate the Answering 
System from any touch tone phone.
A synthesized voice menu will guide
you on how to operate the unit
(p. 56).
•To skip the voice menu and operate the 
unit directly, see page 57.
• The unit will announce the remaining recording time after playback, if i\
t is less
than 5 minutes.
* If “ No new messages ” is heard, the Answering System has only old messages. 
If “ No messages ” is heard, the Answering System has no messages.
Summary of remote operation
Call your unit from a touch tone phone.
Enter your remote code (p. 55) during or after the greeting message.
•The number of new messages will be announced and the new messages will
be played*.
After 3 seconds, the voice menu will start (p. 56). 
Follow the menu or enter the direct commands (p. 57).
To end remote operation, hang up.
• The messages are saved. 
						

							55
Answering System
For assistance, please call: 1-800-211-PANA(7262)
Remote Code
The remote code prevents unauthorized people from accessing your unit 
and listening to your messages. Choose any 2-digit number (00–99). 
The factory preset remote code is “ 11”. If you do not program your own
remote code, you can use “11”.  
Make sure the unit is not being used and the handset is lifted off the 
base unit.
1
Press (MUTE/FUNCTION).
2
Scroll to “ Initial set ” by pressing 
Öor Ñ, and press á.
3
Scroll to “Set answering ” by pressing Ö
or Ñ, and press á.
4
Scroll to “Remote code ” by pressing Öor
Ñ.
5
Press á.
•The current setting is displayed.
6
Enter a remote code using a  2-digit
number (00–99) .
7
Press á(Save key).
•A beep sounds.
• To exit the programming mode, press  (OFF).
• You can exit the programming mode any time by pressing  (OFF)
.
To check the remote code 
Repeat steps 1 to 5.
•The remote code is displayed. When finished, press  (OFF).
Date and time
HInitial set
--------------
Recording time
HRemote code--------------
Remote code :11
H=Save
Remote code:35
H=Save
Set tel line
HSet answeringHS register 
						

							56
Remote Operation from a Touch Tone Phone
All message playback.
All recorded messages are played 
back. At the end of the last
message, “End of final message ” is
heard. The unit will announce the
remaining recording time if it is
less than 5 minutes.
• 3 seconds after playback, the voice menu will start again from the begin\
ning.
• If you hear “ Memory full” after playback, erase some, or all, of the messages
(p. 57).
Voice Menu
The shaded parts are voice prompts.
Press 1 to play back 
all messages.
Press 2 for other
functions.
Press (2). Press 
(1).
Press 1 to play back 
new messages.
Press 2 for other
functions.
Press (2).
Press 1 to record 
your message.
Press 2 for other
functions.
Press (2).
Press 1 to erase all 
messages.
Press 2 for other
functions.
Press (1).
Press (1).
Press (1).
New message playback.
Only new messages are played 
back. At the end of the last
message, “
End of final message ” is
heard. The unit will announce the
remaining recording time if it is
less than 5 minutes.
Please leave your message.
You can leave your own voice 
memo message.
1. Talk after you hear “ Please leave
your message ”.
2. When you finish recording, hang up.
“No messages ” is heard, and all
recorded messages are erased.
Press (2). 
						

							57
Answering System
For assistance, please call: 1-800-211-PANA(7262)
Direct Remote Operation
Once you have entered the remote code, you can also control your unit by\
 
direct commands instead of using the voice menu. To end the remote
operation, hang up anytime.
Direct commands
NEW MESSAGE PLAYBACK 
•Only new messages are
played back.
ALL MESSAGE PLAYBACK
• All messages are played back.
REPEAT (During playback)
• The current message is
repeated.
• If you press within 5 seconds
of playback, the previous
message will be played.
SKIP (During playback)
• The current message is
skipped. The next message is
played.
STOP
• Operation is stopped
temporarily.
• To resume operation, enter a
direct command within 15
seconds, or the voice menu
will start (p. 56).(4) 
(5) 
(1) 
(2)
(9)ERASING A SPECIFIC  
MESSAGE 
(During playback)
• The current message is
erased.
• A short beep will sound
and the next message will
be played.
ERASING ALL MESSAGES
•All recorded messages are
erased.
• A long beep sounds, and
“No messages ” is heard.
ANSWERING SYSTEM OFF
•The unit hangs up and will
not answer calls until
turned on again 
(p. 49, 53, see below).
(*)(4) 
(*)(5)
(0)
Turning on the Answering System
Call your unit and wait for 15 rings.
•The unit will answer and the greeting message will be played.
• The Answering System will be turned on. Hang up or enter the remote code\
 for 
other options.
• When turning on the Answering System using a rotary or pulse service tel\
ephone,
you cannot enter the remote code for other options.
Skipping the greeting message
After calling your unit, press (*)during the greeting message.
•The unit skips the rest of the greeting message and you can start record\
ing your
message after the long beep. 
						

							Wall Mounting
58
This unit can be mounted on a wall phone plate.
2
Press the tabs in the direction 
of the arrows (#), then remove
the wall mounting adaptor ( $).
3
Connect the AC adaptor. Tuck
the telephone line cord inside
the wall mounting adaptor, then
push it in the direction of the
arrow ( #and  $).
•The word “UP WALL” should face 
upward.
1
Push the hook and turn it around. 
Turn the hook until a click is heard.
2
11
Base unit
12
2
To Power 
Outlet 
						

							59
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord. 
Mount the unit, then slide down.
•Raise the antenna.
5
To charge the handset battery:
Fix the charge contacts ( #) and insert
the hook to the handset hole ( $).
•The CHARGE indicator lights.
2
1
Hook
Hole
OR
Hooks 
						

							$
#%
60
This unit will not function during a power failure. To connect a standar\
d 
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone 
Single-Line 
Telephone Jack
T-Adaptor (KX-J66) Telephone
Line Cord
Adding Another Phone
Wall Mounting
Wall Template
2.45 cm
(15⁄16)
Charger unit
2.45 cm (15⁄16)
Screws 
To Power 
Outlet
The charger can be wall mounted. Connect the AC adaptor. Install screws 
using the wall template below. Mount the charger ( #). Slide it down ( $)
then slide down to the right ( %) until it is secured.