Panasonic Kx Tg2382 Operating Instructions Manual

61
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
If “Recharge ” is displayed and/or “ ” flashes after a few telephone
calls even if the battery was fully charged, replace the battery with a \
new 
Panasonic N4HHGMB00001 or N4HHGMB00005 (HHR-P103) battery. To
order, call the accessories telephone number on page 2.
1
Press the notch on the
handset cover firmly and
slide it as indicated by the
arrow.
2
Remove the old battery and
wait for  a few minutes . 
And insert...

62
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the handset or if you need to register the 
handset to a different base unit of the same model, it may be necessary \
to
cancel the registration.
Only one handset can be canceled at a time near the base unit to which t\
he
handset is currently registered.
Make sure the unit is not being used and the handset is lifted off the 
base unit.
1
Press (MUTE/FU\bCTIO\b\f.
2
Scroll to “Initial set ” by...

63
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the handset to the base unit or a different b\
ase unit of 
the same model, you need to register it to that base unit. The handset w\
ill be
given a new extension number of that base unit. Only one handset can be
registered at a time. Make sure the base unit and the other handsets are not
being used. Registration must be completed within 1 minute.
1
Handset: Press...

Display messageCause & Remedy
The battery needs to be charged. Recharge the 
battery (p. 10, 11).
The battery has been discharged. The handset 
will not work. Charge the battery fully (p. 10, 11).
The handset has lost communication with the 
base unit. Move closer to the base unit, and try
again.
• The called handset/base unit is in use.
•  The handset you are calling is too far from the 
base unit.
•  If the radio communication between the 
handset and the base unit is partially impaired,
this display...

Display message Cause & Remedy
When trying to store an item in the directory, the 
directory memory is full. To erase other items
from the directory, see page 41.
A handset button was pressed while the handset 
was on the base unit or the charger. Lift the
handset and press the button again.
The called handset has not been registered to 
the base unit or you selected your extension
number.
The handset you tried to make a call has not 
been registered to the base unit. Register it 
(p. 63, steps 5 and...

66
Troubleshooting
Problem
“No link to base
Move closer to  
base, try again ” is
displayed and an alarm
tone sounds.
Static, sound cuts in/out, 
fades. Interference from
other electrical units.
The handset does not ring.
The handset display is 
blank.
You cannot store a name 
and phone number in the
directory.
While programming or 
searching, the handset
starts to ring and stops the
program/search.
You cannot make an 
internal/external call with
the handset.
Cordless Telephone
Cause & Remedy
•You are...

67
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
The unit does not display 
the caller’s name and/or
phone number.
The handset display exits 
the Caller List.
You cannot page the 
handset or base unit.
You cannot redial by 
pressing
(PAUSE/REDIAL\f
on the handset.
You cannot have a 
conversation or listening to
messages using the
headset.
Cause & Remedy
•You need to subscribe to a Caller ID service.
•
Other telephone equipment may be interfering 
with your phone. Disconnect...

68
Troubleshooting
Problem
The Answering System is 
on, but incoming messages
are not recorded.
“ ” is displayed and 
the ANSWER ON indicator
flashes rapidly, and no new
messages are recorded.
You cannot access the 
Answering System from
the base unit or the
handset.
You cannot access the 
Answering System from a
touch tone phone.
During playback on the 
handset, incoming call
tones are heard.
When you play back 
messages or you turn the
Answering System on, the
unit announces the wrong
day.
FULL
Cause &...

69
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
General
Problem
The unit does not work.
You cannot program items, 
such as the dialing mode.
Cause & Remedy
•Check the settings (p. 9–11).
• Check whether the dialing mode setting is 
correct (p. 16).
• Charge the battery fully (p. 10).
• Clean the charge contacts and charge again
(p. 11).
• Install the battery properly (p. 10).
• Unplug the AC adaptor of the base unit to
reset. Plug in, and try again.
• The handset has not been...

70
Problem
You cannot register the 
handset at the base unit.
“Recharge ” is displayed,
“” 
flashes or the
handset beeps intermittently.
“ Charge for 15h ” is
displayed and the handset 
does not work.
You charged the battery 
fully, but “ Recharge ” is still
displayed and/or “ ”
continues to flash, or
“ Charge for 15h ” is
displayed.
The CHARGE indicator 
light does not go out after
the battery has been
charged.
If you cannot solve your 
problem
Cause & Remedy
• Charge the battery fully (p. 10).
• The...