Panasonic Kx Tg2352 Operating Instructions Manual

51
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antenna.
5
To charge the handset battery:
Fix the charge contacts (#) and insert
the hook to the handset hole ($).
•The CHARGE indicator lights.
2
1
Hook
Hole
OR
Hooks 

52
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Single-Line
Telephone Jack
T-Adaptor (KX-J66)Telephone
Line Cord
Adding Another Phone
Wall Mounting
Wall Template
2.45 cm
(15⁄16)
Charger unit
$
#
%
2.45 cm
(15⁄16)
Screws
To Power
Outlet
The charger can be wall mounted. Connect the AC adaptor. Install screws
using the wall template below....

53
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
If “Recharge” is displayed and/or “ ” flashes after a few telephone
calls even if the battery was fully charged, replace the battery with a new
Panasonic N4HHGMB00001 (HHR-P103) battery. To order, call the
accessories telephone number on page 2.
1
Press the notch on the
handset cover firmly and
slide it as indicated by the
arrow.
2
Remove the old battery and
wait for a few minutes. 
And insert the new battery
into...

54
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the handset or if you need to register the
handset to a different base unit of the same model, it may be necessary to
cancel the registration.
Only one handset can be canceled at a time near the base unit to which the
handset is currently registered.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (MUTE/FUNCTION).
2
Scroll to “Initial set” by pressing Öor
Ñ,...

55
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the handset to the base unit or a different base
unit of the same model, you need to register it to that base unit. The
handset will be given a new extension number of that base unit. Only one
handset can be registered at a time. Make sure the base unit and the
other handsets are not being used. Registration must be completed
within 1 minute.
1
Handset:Press (MUTE/FUNCTION). 
2...

56
If the Following Appear...
If the unit detects a problem, one of the following messages will be
displayed on the handset. Error beeps or a busy tone will sound.
Display messageCause & Remedy
The battery needs to be charged. Recharge the
battery (p. 9, 10).
The battery has been discharged. The handset
will not work. Charge the battery fully (p. 9, 10).
The handset has lost communication with the
base unit. Move closer to the base unit, and try
again.
• The called handset is in use.
• The handset you...

Display message Cause & Remedy
When trying to store an item in the directory, the
directory memory is full. To erase other items
from the directory, see page 37.
A handset button was pressed while the handset
was on the base unit or the charger. Lift the
handset and press the button again.
The called handset has not been registered to
the base unit or you selected your extension
number.
The handset you tried to make a call has not
been registered to the base unit. Register it 
(p. 19, 55).
• 3 handsets...

58
Troubleshooting
Problem
The unit does not work.
“No link to base
Move closer to base,
try again” is displayed
and an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The handset does not ring.
The handset display is
blank.
Cause & Remedy
•Check the settings (p. 8–10).
•Check whether the dialing mode setting is
correct (p. 14).
•Charge the battery fully (p. 9, 10).
•Clean the charge contacts and charge again
(p. 10).
•Install the battery properly (p. 9)....

59
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
You cannot program items,
such as the dialing mode.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the handset
starts to ring and stops the
program/search.
The unit does not display
the caller’s name and/or
phone number.
The handset display exits
the Caller List.
Cause & Remedy
•Programming is not possible while the
handset is being used.
•Do not pause for over 60 seconds while...

60
Problem
You cannot page the
handset.
You cannot redial by
pressing
(PAUSE/REDIAL)
on the handset.
“Recharge” is displayed,
“”flashes or the
handset beeps
intermittently.
“Charge for 15h” is
displayed and the handset
does not work.
You charged the battery
fully, but “Recharge” is still
displayed and/or 
“”
continues to flash, or
“Charge for 15h” is
displayed.
The CHARGE indicator
light does not go out after
the battery has been
charged.
You cannot have a
conversation using the
headset.
Cause & Remedy...