Panasonic Kx Tg2352 Operating Instructions Manual

							51
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
4
Connect the telephone line cord.
Mount the unit, then slide down.
•Raise the antenna.
5
To charge the handset battery:
Fix the charge contacts (#) and insert
the hook to the handset hole ($).
•The CHARGE indicator lights.
2
1
Hook
Hole
OR
Hooks 
						

							52
This unit will not function during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To order, call the accessories telephone number on page 2.
Standard Telephone
Single-Line
Telephone Jack
T-Adaptor (KX-J66)Telephone
Line Cord
Adding Another Phone
Wall Mounting
Wall Template
2.45 cm
(15⁄16)
Charger unit
$
#
%
2.45 cm
(15⁄16)
Screws
To Power
Outlet
The charger can be wall mounted. Connect the AC adaptor. Install screws
using the wall template below. Mount the charger (#). Slide it down ($)
then slide down to the right (%) until it is secured. 
						

							53
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Battery Replacement
If “Recharge” is displayed and/or “ ” flashes after a few telephone
calls even if the battery was fully charged, replace the battery with a new
Panasonic N4HHGMB00001 (HHR-P103) battery. To order, call the
accessories telephone number on page 2.
1
Press the notch on the
handset cover firmly and
slide it as indicated by the
arrow.
2
Remove the old battery and
wait for a few minutes. 
And insert the new battery
into the handset as shown,
matching the correct 
polarity (#). Press 
the battery down until 
it fits securely into the
compartment ($).
3
Close the cover. Make sure the handset display shows “ ”,
when you place the handset on the base unit or the charger.
•If it does not show “ ”, remove the new battery and wait for 10
minutes; and then insert the battery again. Make sure the handset display
shows “ ”.
4
Charge the new battery for about 15 hours in order to display the
battery strength prompt correctly (p. 9, 10).
1
2
A nickel metal hydride battery that is recyclable powers the
product you have purchased. Please call 1-800-8-BATTERY
for information on how to recycle this battery. 
						

							54
Canceling Registration/Re-registration
Canceling the Handset Registration
If you no longer need to use the handset or if you need to register the
handset to a different base unit of the same model, it may be necessary to
cancel the registration.
Only one handset can be canceled at a time near the base unit to which the
handset is currently registered.
Make sure the unit is not being used and the handset is lifted off the
base unit.
1
Press (MUTE/FUNCTION).
2
Scroll to “Initial set” by pressing Öor
Ñ, and press á.
3
Scroll to “HS register” by pressing Öor
Ñ, and press á.
4
Scroll to “Deregistration” by pressing
Öor Ñ.
5
Press á.
6
Press (3)(3)(5)(DEL.) to delete the
registration memory.
•If you make a mistake, press
(HOLD/INTERCOM/CLEAR), and enter “335”.
7
Press á(Okkey).
•A beep sounds and the registration memory will
be erased on both the handset and the base
unit.
•
If 3 beeps sound, you entered a wrong code. 
The display will return to step 6. Enter “335”.
•To register the handset to another base unit of
the same model, start from step 5 on page 55
or see page 19.
•You can exit the programming mode any time by pressing (OFF)
.
•The handset will not work. To use it again, registration will be required (p. 19, 55). 
Ringer setting
HInitial set
--------------
Voice mail
HHS register
--------------
Registration
HDeregistration
--------------
To deregister
press 3,3,5
:---
H=Ok
To deregister
press 3,3,5
:335
H=Ok
Handset [1]
Deregistered 
						

							55
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Re-registering the Handset
If you want to re-register the handset to the base unit or a different base
unit of the same model, you need to register it to that base unit. The
handset will be given a new extension number of that base unit. Only one
handset can be registered at a time. Make sure the base unit and the
other handsets are not being used. Registration must be completed
within 1 minute.
1
Handset:Press (MUTE/FUNCTION). 
2
Scroll to “Initial set” by pressing Öor
Ñ, and press á.
3
Scroll to “HS register” by pressing Öor
Ñ, and press á.
4
Press áat “Registration”.
5
Base unit:
Press and hold HANDSET LOCATOR
(ALL)until the CHARGE indicator flashes.
6
Handset:
#Press 
á.
$Wait until a long beep sounds and the
display shows the registered number.
The registration will be then complete.
•The registered number “[1]”to “[3]” is shown on 
the top right of the display. 
•You can stop registration by pressing (OFF)on the handset and pressing
HANDSET LOCATOR (ALL)on the base unit.
If you have canceled the handset registration at the previous base unit
(p. 54), start from step 5.
If you have not canceled the handset registration at the previous base unit 
(p. 54), the handset number still remains on that base unit memory. Erase the
handset number from the previous base unit. For KX-TG2352W base unit:
(1) Press and hold HANDSET LOCATOR(ALL)until the CHARGE indicator
flashes. (2) Press and hold HANDSET LOCATOR((1)to (3)) of the handset
number that you want to erase until the CHARGE indicator flashes, then rapid
flashes, then goes out.
Ringer setting
HInitial set
--------------
Voice mail
HHS register
--------------
--------------
HRegistration
Deregistration
Press [ALL] on
base for 3 sec,
then press [
H].
Handset
Registering
Handset [3]
Registered
Ex. Extension number 3 
						

							56
If the Following Appear...
If the unit detects a problem, one of the following messages will be
displayed on the handset. Error beeps or a busy tone will sound.
Display messageCause & Remedy
The battery needs to be charged. Recharge the
battery (p. 9, 10).
The battery has been discharged. The handset
will not work. Charge the battery fully (p. 9, 10).
The handset has lost communication with the
base unit. Move closer to the base unit, and try
again.
• The called handset is in use.
• The handset you are calling is too far from the
base unit.
• If the radio communication between the
handset and the base unit is partially impaired,
this display will be shown.
• If more than one unit is in use, such as
conducting an external/internal call, you may
not be able to program. Try again later.
• You cannot join the conference. A maximum of
2 handsets can take part in a conference call.
• While 2 other handsets are making a
conference call, you cannot operate the
handset. Try again later.
When you tried to register or deregister the
handset, the handset and the base unit could not
link for some reason, such as interference from
other electrical appliances. Take the handset and
the base unit away from the electrical appliances
and try again.
Recharge
Error!! No link to base
Move closer to 
base, try again Charge for 15h
Busy 
						

							Display message Cause & Remedy
When trying to store an item in the directory, the
directory memory is full. To erase other items
from the directory, see page 37.
A handset button was pressed while the handset
was on the base unit or the charger. Lift the
handset and press the button again.
The called handset has not been registered to
the base unit or you selected your extension
number.
The handset you tried to make a call has not
been registered to the base unit. Register it 
(p. 19, 55).
• 3 handsets have already been registered to the
base unit. To cancel another handset
registration, see page 54. 
• This base unit has the memory of the handset
currently registered to another base unit. Erase
the handset memory from the base unit. 
For KX-TG2352W base unit: 
(1) Press and hold HANDSET LOCATOR(ALL)
until the CHARGE indicator flashes.
(2) Press and hold HANDSET LOCATOR
((1)to (3)) of the handset number that you
want to erase until the CHARGE indicator
flashes, then rapid flashes, then goes out.
57
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Invalid Directory full
Invalid.
Please register
to the base. Please lift up
and try again.
All handsets
registered.
Maximum is 3. 
						

							58
Troubleshooting
Problem
The unit does not work.
“No link to base
Move closer to base,
try again” is displayed
and an alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
The handset does not ring.
The handset display is
blank.
Cause & Remedy
•Check the settings (p. 8–10).
•Check whether the dialing mode setting is
correct (p. 14).
•Charge the battery fully (p. 9, 10).
•Clean the charge contacts and charge again
(p. 10).
•Install the battery properly (p. 9).
•Unplug the AC adaptor of the base unit to
reset. Plug in, and try again.
•The handset has not been registered to the
base unit. Register the handset (p. 19, 55).
•Re-install the battery (p. 53) and charge it
fully.
•You are too far from the base unit. 
Move closer to the base unit and try again.
•Plug in the AC adaptor of the base unit.
•Raise the base unit antenna.
•Locate the handset and the base unit away
from other electrical appliances (p. 3).
•Move closer to the base unit.
•Raise the base unit antenna.
•The ringer volume is OFF. Set to HIGH or
MEDIUM or LOW (p. 17).
•While you are making an intercom call, these
handsets do not ring. Instead users will hear
incoming call tones (p. 49).
•Charge the battery fully (p. 9, 10). 
						

							59
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
Problem
You cannot program items,
such as the dialing mode.
You cannot store a name
and phone number in the
directory.
While programming or
searching, the handset
starts to ring and stops the
program/search.
The unit does not display
the caller’s name and/or
phone number.
The handset display exits
the Caller List.
Cause & Remedy
•Programming is not possible while the
handset is being used.
•Do not pause for over 60 seconds while
programming.
•Move closer to the base unit.
•
Ö, Ñ, Üor ámay have been pressed
when you picked up the handset. Press 
(OFF)
and try again.
•If more than one other user is using the
handsets, you may not be able to program.
Try again later.
•You cannot store an item in the directory
while the handset is in the talk, speakerphone
or intercom mode.
•Do not pause for over 60 seconds while
storing.
•To answer the call, press  or  . Start
again from the beginning after hanging up.
•You need to subscribe to a Caller ID service.
•Other telephone equipment may be
interfering with your phone. Disconnect it and
try again.
•Other electrical appliances connected to the
same outlet may be interfering with the Caller
ID information.
•Telephone line noise may be affecting the
Caller ID information.
•The caller requested not to send his/her
information. See page 25.
•If a call is being transferred to you, the caller
information will not be displayed.
•Do not pause for over 60 seconds while
searching. 
						

							60
Problem
You cannot page the
handset.
You cannot redial by
pressing
(PAUSE/REDIAL)
on the handset.
“Recharge” is displayed,
“”flashes or the
handset beeps
intermittently.
“Charge for 15h” is
displayed and the handset
does not work.
You charged the battery
fully, but “Recharge” is still
displayed and/or 
“”
continues to flash, or
“Charge for 15h” is
displayed.
The CHARGE indicator
light does not go out after
the battery has been
charged.
You cannot have a
conversation using the
headset.
Cause & Remedy
•The called handset is too far from the base
unit.
•The called unit is in use. Try again later.
•If more than one other user is using the
handsets and base unit, you may not be able
to page. Try again later.
•If the last number dialed was more than
32 digits long, the number will not be redialed
correctly.
•The button has a double function as either
redial or pause. It will redial the last number
dialed if pressed at the outset of a call 
(p. 22). If another number has been dialed
first, it will operate as a pause button (p. 47).
•Charge the battery fully (p. 9, 10).
•The battery has been discharged. Charge the
battery fully (p. 9, 10).
•Clean the charge contacts and charge again
(p. 10).
•Install a new battery (p. 53).
•This is normal.
•Make sure that an optional headset is
connected properly (p. 11).
•If “SP-phone” is displayed on the handset,
press  to switch to the headset.
Troubleshooting