Panasonic Kx-Td500 Features Guide

PFeatures Guide
202 Features Guide
Power Failure Re-start
DescriptionWhen turning back on the electricity, the system re-starts the stored
data automatically.  Before re-starting, the system records the error
log if necessary.
Conditions¥ Memory Protection
In the event of a power failure, system memory is protected by a facto-
ry-provided lithium battery.  
Programming References
No programming required.
Feature ReferencesNone 
Operation ReferencesNot applicable. 

Features GuideP
Features Guide 203
Power Failure Transfer
DescriptionPower Failure Transfer connects specific telephones (any SLT and
a certain type of PT) to the pre-determined CO lines in the event of
system power failure.
Conditions¥  Up to 192 pairs of extension/CO connection are available to maintain a
conversation when power is restored or TSW recovery.
¥ Auxiliary Connection between the Trunk card and the Extension card
should be done as per the System Programming so that conversation is...

PFeatures Guide
204 Features Guide
Privacy, Automatic   
DescriptionBy default all conversations established on CO lines, extension
lines and doorphone lines have privacy activated, that is, an exist-
ing call is not interrupted by anyone.
Conditions¥  Privacy Release
Automatic privacy may be temporarily released to establish a 3-party
conference, either by Executive Busy Override or Privacy Release.
Programming References
No programming required.
Feature ReferencesExecutive Busy Override Ð Executive...

Features GuideP
Features Guide 205
Privacy Release 
DescriptionAllows the PT user to release Automatic Privacy for an existing
call in order to establish a 3-party call.  During a conversation with
an outside party on a CO button, the extension user can allow
another extension user to join in the existing call by pressing the
CO button. 
Conditions¥  Confirmation Tone
When a 2-party call is changed to a 3-party call and vice versa, a
confirmation tone is sent to all three parties.  Eliminating the tone...

PFeatures Guide
206 Features Guide
Pulse to Tone Conversion
DescriptionAllows the extension user to change the dialing mode from pulse
dial to tone dial (DTMF) temporarily during a call so that they can
access special services which require tone dialing such as a com-
puter-accessed long distance call.
Conditions¥  This feature works only on CO lines set to Pulse Dialing mode.
¥ Dial Type Selection provides selection of a dial mode for each CO line.
¥DISA
This feature is not available during a DISA...

Features GuideQ
Features Guide 207
Quick Dialing
DescriptionAllows the extension user to call a desired party by dialing a short
code (1-digit code).  Quick Dialing is convenient for room service
calls in a hotel, for example.
Conditions¥ To utilize this feature, an extension number or a telephone number
should be stored beforehand either by User or System Programming.
¥ Up to eight quick dial numbers can be stored in the system.
¥ Assign a feature number in program ÒNumbering PlanÓ first and then a...

RFeatures Guide
208 Features Guide
Redial, Last Number
DescriptionEvery extension telephone in the system automatically saves the
last telephone number dialed to a CO line and allows the extension
user to dial the same number again with a simple operation.
Conditions¥ Up to 24 digits (excluding the CO line access code) can be stored and
redialed. 
¥ The memorized telephone number is replaced by a new one if at least
one digit sent to a CO line is dialed.  Dialing a CO line access code
alone does not...

Features GuideR
Features Guide 209
Redial, Saved Number
DescriptionAllows the PT user to save a telephone number of the current call
and redial the number afterwards.  The PT user can store it during
a call on a CO line.  The saved number can be redialed repeatedly
until another number is stored.  
Conditions¥ Up to 24 digits (not including the CO line access code) can be stored
and redialed. 
¥ SAVE button
If the SAVE button is not provided on a PT, it can be assigned to a
flexible (CO, DSS, PF) button...

RFeatures Guide
210 Features Guide
Released Link Operation
DescriptionWhen Released Link Operation is enabled, an extension user will
be automatically released from a call (extension, outside) after
transferring it to the destination, if the destination extension is idle.
This feature simplifies the transfer operation by eliminating the
need for going on-hook or pressing the RELEASE button after
transferring the call.
This feature is convenient for extension users, such as Operators,
who handle a large...

Features GuideR
Features Guide 211
Remote Station Feature Control
DescriptionAllows both the Manager and the Operators to set and cancel the
following features for other extensions.
Remote Station Lock
Used to lock other extensions so that no one can make an outside call
or an intercom call (except an operator call) from those extensions.
Caller ID Log Lock Clear
Used to clear the Caller ID Log Lock Code set by an extension
user.
This is convenient when an extension user cannot remember his or
her own...