Panasonic Kx-Ta624 Advanced Hybrid System User Manual

Telephone Features3-75
3.2 Telephone FeaturesL
Having a conversation with a party
PT
Lift the handset or press SP-PHONE, or the flashing Live Call Screening button.
or
During a conversation with another party;
When the extension user is having a conversation, the Call Waiting tone will be heard if
Call Waiting has been enabled. The Live Call Screening indicator light flashes.
— If you want to terminate the current call
Monitoring
— If you want to hold the current call
Monitoring
PT
Hang up or press...

3-76Telephone Features
L3.2 Telephone Features
Conditions
• A flexible CO or DSS button can be assigned as the Live Call Screening (LCS) button
or the Live Call Screening (LCS) Cancel button.
• The Live Call Screening indicator shows the feature status as follows:
Red (steady). . . . . . . . . . . The Live Call Screening mode is on.
Off  . . . . . . . . . . . . . . . . . The Live Call Screening mode is off.
Flashing green slowly . . . Live Call Screening is active.*
Flashing green rapidly . . . An alert...

Telephone Features3-77
3.2 Telephone FeaturesL
Lockout
If one party in a conversation goes on-hook, both parties will be disconnected from the
speech path automatically. A reorder tone is sent to the off-hook party before it is
disconnected. No operation is necessary.
Log-In/Log-Out
Allows you to assign the Log-In mode or Log-Out mode within a hunting or ring group.
When in the Log-Out mode, you can leave the group temporarily, preventing hunting
calls from being sent to your extension. The lighting...

3-78Telephone Features
L3.2 Telephone Features
Conditions
• The default is “Log-In” mode.
• There should be at least one extension that is in Log-In mode.
• If every extension has logged out except one person, and that person tries to log out,
their extensions will display “Not Valid”. In other words, the last member of the group
cannot log out.
• The Log-In/Log-Out button can be assigned to a flexible CO button.
Programming References
• Station Programming (Section 2)
Flexible Button Assignment —...

Telephone Features3-79
3.2 Telephone FeaturesM
Message Waiting
When the called extension is busy or does not answer your call, you can leave a
notification so that the called party may call you back.
As a message receiver, the MESSAGE button light lets you know that a call has been
received. If you receive notification, you can call back the original party by a simple
operation. This operation is available only for proprietary telephones with MESSAGE
buttons.
Setting
Any Telephone
Dial 701.Enter the...

3-80Telephone Features
M3.2 Telephone Features
Checking and Selecting a message notification by the message receiver
If there is a message, the message waiting lamp (MESSAGE indicator) light will be on.
PT
Press MESSAGE repeatedly until the desired message appears.
MESSAGE
When the telephone is idle and on-hook
• The stored messages are shown on the display in the order they were received.
• When Tony at extension 123 left a message:

123:Tony
• If you have more than one message at your
extension, the...

Telephone Features3-81
3.2 Telephone FeaturesM
Conditions
• Each extension can have a maximum of 8 simultaneous messages. If you try to set the
ninth message, you will hear a reorder tone.
• If the MESSAGE indicator does not go out after calling the extension which left the
message, another message is waiting.
• If multiple message notifications are left at your extension, call back is executed in the
order received.
• If you select a specific message to call back, the other call backs will be executed in...

3-82Telephone Features
M3.2 Telephone Features
Condition
• This feature is only available during a hands-free conversation.
Mixed Station Dialing
Any telephone, either a KX-T7030/KX-T7020/KX-T7050/KX-T7055/KX-T7130, single
line rotary phone (10 pps, 20 pps) or single line touch tone telephone, may be used as an
extension for the system. PT
Microphone Mute (— for KX-T7020/KX-T7030/KX-T7130 only)
Allows you to turn off the microphone so you can consult privately with others in the
room. You will still be...

Telephone Features3-83
3.2 Telephone FeaturesO
Conditions
• The destination numbers are stored through Station Programming.
• You may press a CO button to select a desired outside (CO) line before pressing the
One-Touch Dialing button.
• “Speed Dialing”, “One-Touch Dialing” and manual dialing can be used together.
• You can store a number consisting of twenty-five digits or more by dividing and storing
it into two One-Touch Dialing buttons.
• The telephone number dialed will be displayed on the LCD. Use...

3-84Telephone Features
O3.2 Telephone Features
Condition
• If an operator is not assigned, this feature is not available and you will hear a reorder
tone.
Programming Reference
• System Programming — Installation Manual
[008] Operator Assignment
Operator Call
Allows you to call an operator within the system. One extension can be assigned as an
operator.
Any Telephone
Dial 0.
0
Lift the handset or press 
SP-PHONE/MONITOR.