Panasonic Kx Ta308 User Manual

PT Overview1-9
1.1 Configuration
Flexible Buttons
Flexible Buttons do not have specific features permanently assigned to them. Features are
assigned to Flexible Buttons through Station Programming. “Flexible Button
Assignment” is addressed in Station Programming (Section 2). The two types of Flexible
Buttons are as follows.
• Flexible CO Buttons
• Flexible MESSAGE Button
The following table outlines the features that can be assigned to the Flexible Buttons.
“✔” indicates that the feature is...

1.1 Configuration
1-10PT Overview
The following table shows the default settings of the Flexible CO button\
s.
CO button
LINE 1
LINE 2
LINE 34*
5 *
6 *
7 *
8 *
9 *
10 *
11 *
12 * Feature
S-CO
S-CO
S-CODSS
DSS
DSS
DSS
DSS
DSS
DSS
One-
Touch 
Dialing
One-
Touch 
Dialing
Ext.101
CO1
CO2
CO3
Ext.102
Ext.103
Ext.104
Ext.105
Ext.106
Ext.107
Ext.108
Paging
ANSWER
Paging —All
Ext.102
CO1
CO2
CO3
Ext.101
Ext.103
Ext.104
Ext.105
Ext.106
Ext.107
Ext.108
Paging
ANSWER
Paging —All
Ext.103
CO1
CO2
CO3
Ext.101
Ext.102...

PT Overview1-11
1.1 Configuration
Line Access Buttons
One of the following three types of CO buttons must be used to seize an \
outside (CO)
line when making a call.• Group-CO (G-CO) button
• Other-CO (O-CO) button
• Single-CO (S-CO) button
Conditions
• A Flexible CO button can be assigned as a Line Access Button (G-CO, O-CO or S-CO)in Station Programming. Once a Flexible CO button is assigned as a Line \
Access
Button, it provides the line status using lighting patterns and color in\
dication. Please...

1.1 Configuration
1-12PT Overview
Other-CO (O-CO) Button
Outside (CO) lines which are not assigned to S-CO or G-CO buttons can \
be assigned to a
Flexible CO button on a proprietary telephone. The assigned button serves as the O-CO
button. An incoming call, on assigned outside (CO) lines, arrives at the O-CO \
button. To
make an outside call, you simply press the designated O-CO button.
Programming Reference
• Station Programming (Section 2)Flexible Button Assignment — Other-CO (O-CO) Button
Feature...

PT Overview1-13
1.1 Configuration
Initial Settings
Display Contrast Adjustment (KX-TA30830 only)*
The Navigator key is used to adjust the display contrast.
PT
Press Left or Right.
While on-hook or receiving a call
PT
Slide the lever of BACKLIGHT Control Selector 
to the desired setting (2: HIGH/1: LOW/0: OFF).
BACKLIGHT2
0
1
BACK LIGHT Adjustment (KX-TA30830 only)
The BACKLIGHT Control Selector is used to adjust the brightness of the 
BACKLIGHT.
* The above settings may be initialized to default settings...

1.1 Configuration
1-14PT Overview
PT
Slide the lever of the RINGER Volume Selector 
to the desired setting (HIGH/LOW/OFF).
RINGER
PT
Press SP-PHONE
or MONITOR.Press Up or Down.
While on-hook or during a conversation using a handset
SP SP-
PHONE
MONITOR MONITOROR OR
  ************  (-volume level 12)
To adjust the ringer volume
To adjust the speaker volume*
Volume Control — Handset Receiver/Headset/Ringer/Speaker
Allows you to adjust the following volume settings as necessary.
— Handset Receiver volume
—...

PT Overview1-15
1.1 Configuration
LED Indication
The Light Emitting Diode (LED) buttons indicate the line conditions wi\
th lighting
patterns.
Flashing light patterns
LED Indication on the INTERCOM Button
The table below shows the lighting patterns for intercom line conditions\
.INTERCOM Button
Off
Green On
Flashing Green Slowly
Flashing Green Moderately
Flashing Green Rapidly Intercom Line Condition
Idle
Intercom call / Conference established
Intercom call hold
Intercom call exclusive hold
Incoming...

1-16PT Overview
1.1 Configuration
LED Indication and LCD on the KX-T7885/KX-TD7895
The LED is off and LCD date and time line is not displayed while the phone is idle. To
activate the LED and LCD, press the button specified in the “Operating Instructions” for
the wireless phone. 

Section 2
Station Programming
(Personal Programming)
Contents
2.1 Station Programming Instructions  ...................................2-2
2.2 Station Programming (Personal Programming)  .............2-6 

2-2Station Programming (Personal Programming)
2.1 Station Programming Instructions
When storing data
After pressing the STORE button to store data, you may hear one of the following tones.
— Confirmation tone (one beep): storage is completed.
— Confirmation tone (two beeps): the data is the same as the last entry.
— Alarm tone (three beeps): the entry is not valid.
To exit the Station Programming mode
Station Programming allows you, the proprietary telephone (PT) user, to program certain
features from your...