Panasonic Iris Reader Bm Et200 Operating Instructions

8 Pin No.
21
1
2
3
4
5
6
7
OFF Tamper detection
cancelCancels the tamper
detection. Set this
switch to ON when the
front cover is removed
for servicing.Cancel Detect After servicing, set
this switch to OFF.
If the front cover is
attached with this
switch ON, buzzer
sound is activat-
ed. OFF Ethernet Full/Half Ethernet setting Half Full Available only
when 5 is ON OFF Ethernet 100 M/
10 MEthernet setting 10 M 100 M Available only
when 5 is ON OFF Ethernet auto-
negotiationEthernet setting Fixed...

Pin No.
Pin No.
22
SW1-1
SW1-2 OFF RS-485 termination
(card reader)Selects whether to
activate the termina-
tion of the RS-485
connection with the
card reader.RS-485 ter-
mination
ONRS-485 ter-
mination
OFF or
WiegandAvailable only when SW2-3
and SW2-4 are OFF (RS-
485 is selected). When
selecting Wiegand, surely
set this switch to OFF.
Otherwise, communication
may not be established. Factory
default
OFF RS-485 termination
(access control
panel)Selects whether to
activate the termina-
tion of the RS-485...

23
Cautions:
• Attach this iris reader to a flat wall. After the installation,
secure the iris reader to prevent dropping.
• This system must be installed within the protected
premise in accordance with the National Electrical
Code(NFPA70), and local authorities having jurisdiction.
• All interconnecting devices must be UL listed.
• Alarm output2 (tamper detection) must be connected to
UL Listed Access Control Panels to disable operation
during tamper alarm.
Installation and Connections
ON
1234ON
1234
+...

Power cable (Mandatory)
24
Description about the Connection Example
• When the power supply is shut down, an alarm signal is supplied from the alarm output 1 (power status) to alarm devices.
• When the front cover is removed from an iris reader or the iris reader is removed from the wall, an alarm signal is sent from
the alarm output 2 (tamper detection) to alarm devices.
• When recognition is not successfully completed, an alarm signal is sent from the recognition result output 2 (REJECT) to a
digital...

25
Item
Junction box
Rear cover fixing screw
(Mandatory)
GND cable (Mandatory) _ Solder both ends of the cable with M3 screw
clamp terminals. Use the supplied earth ground
cable to connect the earth ground. Two gang junction box (4 in. x 4 in.) Necessary when attaching the rear cover to the
wall Item number/Recommended type Use
*1Only cables without connector covers are usable.
Notes:
• When you use the alarm output and Wiegand terminals, you need optional cables suited for the connectors of external...

26
•Incandescent or halogen lighting
•Places where the iris reader or the users eyes are directly exposed to light
Notes:(A quantity of acceptable near-infrared ray is 500 µW/cm
2or less.)
•Places near the light reflection (from a mirror, etc.)
•Places where the amount of light is not appropriate for operation
Keep the iris reader away in the following, in addition to the above surroundings.
•Vibration (It may cause invalid iris image capturing and recognition. It may also cause other trouble or...

27
Check the Capturing Range.
If the height of the iris reader is 1 240 mm {48.8 in.} as described in the previous Side View illustration, the recognition range
will become as follows.
Note:If your eye position is higher than the upside limit, bend down. If your eye position is lower than the downside limit, get
on a pedestal, etc.
0 
12 mm {0.47 in.} 300 mm {12 in.}
400 mm {15.7 in.}1 678 mm {66.1 in.}
Upside limit of the eye position
1 395 mm {54.9 in.}
Center of optical axis
(Recommended installation...

3. Detach the rear cover from the main unit by removing
the mounting screws.
4. Secure the rear cover to the wall or junction box built in
a wall with the locally procured screws, and fix the tam-
per detection lever on the wall.
Important:
•To work tamper detection properly, mount tamper
lever to the wall by screw.
•The tamper detection lever is crucial to function of
the tamper, and needs to be attached securely to
the wall for the tamper to work properly.
5. Attach the main unit to the rear cover.
(1)...

29
6. Connect the LAN cable and audio output cable to the
iris reader.
Attach the ferrite core supplied to the LAN cable and
audio output cable.
7. Fix the power cable to the iris reader with the supplied
clamping tool and clamping screw.
(Cut off the extra portion of clamping tool.)
8. Connect the DC 12 V or DC 24 V power cable to the iris
reader.
Important:
•Do not mistake + and –. The wrong cable connec-
tion may cause trouble.
•Do not connect an AC power-supply device. The
iris reader works 12 V...

30
(2) Insert the option camera firmly into the CN6 con-
nector until the connector clicks.
(3) Insert the video output cable supplied to the option
camera firmly into the CN7 connector, and connect
the video output cable of the option camera to the
the video input cable connected to an external
device (for example, a digital disk recorder).
14. Remove the sheet from the back side of front cover.
15. Attach the front cover to the main unit.
Fit the screw hole and protrusions of front cover in the
main...