Panasonic Iris Reader Bm Et200 Operating Instructions

11
• The settings of this apparatus are configured by the
setup PC or iris server.
The operational setting of stand-alone mode is config-
ured using the setup PC. The operational setting of net-
work mode is configured using the optional
Administration Software BM-ES200, which is to be
installed in the iris server.
Depending on the settings, the voice guidance will not
be output or the live indicator will be off at all times.
Refer to system administrators for details on settings.
* If the previous...

12
Document Convention
Stand-alone mode:In this mode, the iris reader can be used in the stand-alone operation. Iris server is not required. The max-
imum number of users that can be registered is 50.
The users are registered with the numeric key. Registration from the browser installed on the setup PC is also available.
Network mode:In this mode, iris server is used for connection with the iris reader. The administration software, iris server, and
network connection are required. The number of users...

13
Recognition mode:While the iris camera is being used in the stand-alone mode, the following control mode becomes avail-
able: recognition mode or administrator mode. Iris recognition is available in the recognition mode. In the usual operation,
recognition mode will be applied.
Administrator mode:While the iris camera is being used in the stand-alone mode, the following control mode becomes avail-
able: recognition mode or administrator mode. Iris reader setup and iris and data enrollment, etc. are...

14
Notification About This Document
• This document describes basic operating instructions of Iris Reader BM-ET200.
• Installation and Connections (p. 23) in this document are intended for service personnel.
• Manuals supplied to Administration Software BM-ES200, which is the software required for iris data enrollment, describe
the operating instructions of the software, examples of system composition, and setup guide. These manuals are intended
for system installers and administrators.
Normally, users...

performing the setup using the administration software,
web browser, or numeric key. Refer to system adminis-
trators for details on the settings.
Mute:Voice guidance is not output.
Simple:Recognition result are output. Voice guidance
is not output.
Full:Voice guidance and recognition result are output.
iResult indicators
These indicators inform you of recognition results.
ACCEPT:This indicator lights up when recognition is
successfully completed.
REJECT:This indicator lights up when recognition is
not...

16
!2High speed serial interface
This connector is used when an external numeric key or
memory device is connected. Attach the cover when
not using the connector.
Note:Refer to the dealer for available external devices.
“High speed serial interface” is only used in the stand-
alone mode, and the stand-alone mode has not been
evaluated by UL.
Rear View
Remove the cable hole cover by loosening the screws with a Phillips screwdriver.
Reinforcing screw holes
Mounting screw holes
Tamper detection lever
Cut...

■Internal View
●Front View
■Specifications of Connector Terminal
Notes:
•Wiegand and RS-485 interfaces are available in the network mode only. In\
 the stand-alone mode, these interfaces are
unavailable.
• Wiegand/RS-485 interface, output width of Recognition result output 1 an\
d 2 are configured by the administration software.
Refer to BM-ES200 Operating Instructions (supplied to Administration So\
ftware BM-ES200) for details on communication
setup.
17
ON
1234ON1234
Cable hole
Power terminal
Connector...

Pin No. Pin No. Port Name
q-1
q-2
q-3
q-4RECOGNITION START
TRIGGER INTPUT
RECOGNITION START
TRIGGER INTPUT GNDIN An alarm signal is input to
this terminal to start recogni-
tion.0 V to 5 V DC, 24 mA (Max),
Active low,
Pulse width: 200 ms or more RECOGNITION RESULT
OUTPUT 1
ACCEPTRLT1
GND
TRG
GND RECOGNITION RESULT
OUTPUT 1 GND
ACCEPTOUT Recognition result output 1
This terminal is activated
when recognition is success-
fully completed.24 V DC, 100 mA (Max)
Make contact output
Normally Open contact
Active...

w
-12 Pin No. Port NameLabel
marking
REJECT-LED
(access control
panel) w-5
w-8
w-9
w-10
w-11
ALARM OUTPUT 2
TAMPER DETEC-
TION GND− ALARM OUTPUT 2
TAMPER DETEC-
TION−OUT This terminal is activated
when the iris reader
enters the tamper detec-
tion mode by the tamper
detection switch at the
front or rear panel (acti-
vated until the tamper
detection mode is can-
celed).24 V DC, 24 mA (Max)
Open collector output
Normally Open contact
Active low DATA 1/RS-485 (A)
(access control
panel)Wiegand
RS-485(A)...

w-20 w-13Port NameLabel
marking
w-14
w
-15
w-16
w-17BUZZER INPUT BUZZ−
w-18
w-19TIME ADJUST
INPUTSYNC−IN An external master clock
is connected.
Refer to the dealer for
available external
devices.0 V to 5 V DC, 24 mA
(Max), Active low,
Pulse width: 100 ms or
more
TIME ADJUST
INPUT GNDGND− BUZZER INPUT
GNDGND−IN An alarm signal is input to
this terminal to activate
buzzer sound.0 V to 5 V DC, 24 mA
(Max), Active low,
Pulse width: 200 ms or
more RECOGNITION
RESULT OUTPUT 2
REJECTRLT2
RECOGNITION
RESULT...