Panasonic Integrated Telephone System Kx Ts3282 Operating Instructions

							 
11  
Preparation
 
For assistance, please call: 1-800-211-PANA(7262) 
Connecting Telephone Line Cords 
A maximum of eight KX-TS3282Ws can be connected in parallel. You can 
also connect KX-T3281W.
To use the intercom, you must connect the telephone line cord to the 
LINE1/2 telephone jack of the unit. 
•If another model telephone is connected to the KX-TS3282W except for 
KX-T3281W, the line indicators of this unit will not function for that telephone. 
To connect the units to individual two-line telephone jacks
 
Parallel connected two-line telephone jacks 
•You can connect up to 8 stations (KX-TS3282W and/or KX-T3281W). 
DSL Internet connection and KX-TS3282W Intercom work at similar 
frequencies. Please contact Panasonic at 1-800-211-PANA(7262) for 
special wiring configurations.
LINE2/DATA LINE1/2
Two-Line Telephone Jacks (RJ14C) Parallel Connected
To another KX-TS3282W 
or KX-T3281W
4-Wire Telephone Line 
Cord with GREEN Plugs
GREEN Plug 
						

							 
Installation 
12 
•If you re-connect the telephone line cord(s), confirm that all of the extension 
indicators light with the AC adaptor connected, then connect the telephone line 
cord(s). If all of the extension indicators do not flash, the extension number has 
been assigned to this unit and the number might be used for another unit on the 
same line. Erase the previously assigned number (p. 17), then connect the 
telephone line cord(s). Re-assign the number to the unit (p. 17).  
If you provide only one two-line telephone jack for the units, continue to 
wire them using optional Panasonic T-adaptors KX-J66. To order, call the 
accessories telephone number on page 3. 
To connect the units to a two-line telephone jack 
DSL Internet connection and KX-TS3282W Intercom work at similar 
frequencies. Please contact Panasonic at 1-800-211-PANA(7262) for 
special wiring configurations.
LINE2/DATA LINE1/2LINE2/DATA LINE1/2
T-Adaptor 
(KX-J66)T-Adaptor 
(KX-J66)
4-Wire Telephone 
Line Cord with 
GREEN Plugs
LINE 1
LINE 2
4-Wire Telephone Line Cord 
with GREEN Plugs4-Wire Telephone 
Line Cord with 
GREEN Plugs GREEN 
PlugGREEN 
PlugGREEN 
PlugGREEN 
Plug
Two-Line 
Telephone Jack 
(RJ14C)
To another KX-TS3282W 
 or KX-T3281W 
						

							 
13  
Preparation
 
For assistance, please call: 1-800-211-PANA(7262) 
If you provide only two single-line telephone jacks for the units, continue to 
wire them using optional Panasonic T-adaptors KX-J66. To order, call the 
accessories telephone number on page 3. 
•If you do not connect other extensions, you do not need to use a T-adaptor. 
Connect a 2-wire telephone line cord to the LINE1/2 telephone jack of the unit 
directly. 
To connect the units to two single-line telephone jacks 
DSL Internet connection and KX-TS3282W Intercom work at similar 
frequencies. Please contact Panasonic at 1-800-211-PANA(7262) for 
special wiring configurations.
LINE2/DATA LINE1/2LINE2/DATA LINE1/2
4-Wire Telephone 
Line Cord with 
GREEN Plugs
4-Wire Telephone Line Cord 
with GREEN Plugs4-Wire Telephone 
Line Cord with 
GREEN Plugs
2-Wire Telephone 
Line Cord with 
TRANSPARENT 
Plugs
To another 
KX-TS3282W 
or KX-T3281W
Single-Line 
Telephone 
Jacks (RJ11C)
GREEN 
Plug
TRANS-
PARENT 
PlugGREEN 
Plug
GREEN 
PlugGREEN 
Plug T-Adaptor 
(KX-J66)
T-Adaptor 
(KX-J66)
LINE 1 LINE 2 
						

							 
Installation 
14 
Connecting a Communication Device 
After connecting the telephone line cord to a two-line telephone jack, you 
can connect a communication device (computer, modem, fax, answering 
machine, etc.) through this unit using the LINE2/DATA jack. 
•If the communication device is in use, use LINE 1 to make or answer other calls. 
Otherwise the communication device may not operate properly.
4-Wire Telephone
Line Cord  with
GREEN Plugs
Two-Line 
Telephone Jack 
(RJ14C)
LINE2/DATA LINE1/22-Wire Telephone
Line Cord with
TRANSPARENT
Plugs
TRANSPARENT
PlugGREEN
Plug
•Computer
•Modem
•Fax
•Answering Machine 
						

							 
15 
Preparation
 
For assistance, please call: 1-800-211-PANA(7262) 
Time and Date 
You can select 12-hour clock (AM/PM) or 24-hour clock by programming. 
Make sure that the handset is on the cradle, the AC adaptor is connected 
and the SP-PHONE/HEADSET indicator light is off. 
After the AC adaptor is connected, the display 
will show “ 
Set clock 
” for 60 seconds. 
•If the display exits the set clock menu, press  
[FUNCTION/EDIT], then scroll to “Set clock” by 
pressing [] or [].
1Press [] or [ENTER] (Yes key).
2(1) Enter the time (hour and minute) 
using [], [] and 
[].
•You can scroll to the desired hour/
minute by pressing [] or [].
To move forward, press []. To move 
backward, press [].
•For 12-hour clock, enter “0100” to “1259”.
For 24-hour clock, enter “0000” to “2359”. 
•
If you entered “00” or between “13” and “23” 
for the hour, enter the minute and press 
[], then go to step 3
.
•You can also enter the time using the 
dialing buttons ([0] to [9]).
(2) For 12-hour clock, select “AM” or 
“PM” by pressing [] or [], and 
press [].
For 24-hour clock, if the hour is 
between 1 and 12, erase “AM” or 
“PM” by pressing [] or [], and press [].
-•You can also select “AM” or “PM” or 
erase it by pressing [].
3Enter the month and day using [], [] 
and [].
•You can scroll to the desired month/day 
by pressing [] or []. To move forward, 
press []. To move backward, press [].
•You can also enter the month/day using the dialing buttons ([0] to [9]).
(Continued )
Set clock
       ENTER=Yes
     
12:00AM 01/01
            2002
   ENTER=Save

09:30AM 01/01
            2002
   ENTER=Save
Ex. Time: 09:30



09:30PM 01/01
            2002
   ENTER=Save

09:30PM 12/27
            2002
   ENTER=Save
Ex. Dec. 27


Programmable Settings 
						

							Programmable Settings
16
4Enter the year using [] and [].
•You can select the year between 2000 
and 2099.
•You can also select the year entering the 
last 2-digits using the dialing buttons ([0] 
to [9]).
5Press [ENTER] (Save key).
•A beep sounds.
•The clock starts working.
•If 3 beeps are heard, the setting is not 
correct. Start again from step 2.
•The display will go to the extension 
number assigning menu as shown on the 
right if you had started programming 
within 60 seconds after plugging in the 
AC adaptor. The menu will remain for 60 
seconds. To assign a number, see page 
17, from step 4.
•You can exit the programming mode any time by pressing [EXIT].
To adjust the time and date
1. Press [FUNCTION/EDIT].
2. Scroll to “Set clock” by pressing [] or 
[], and press [].
3.  Adjust the time and date, using [], [], [] 
or [].
4. Press [ENTER] (Save key).
If a power failure occurs, the adjusted time/date will be retained by installing the 
batteries (p. 9). Readjust if “” flashing on the display.
For Caller ID service users (p. 29)
•The Caller ID information will reset the clock after the first ring if the adjusted 
time is incorrect. 
•If the clock has not previously been set, the Caller ID information will not adjust 
the clock.
•The Caller ID information will automatically adjust the clock for daylight saving 
time.
09:30PM 12/27
            2002
   ENTER=Save
 Extension#
 12345678 Erase
     ENTER=Save
Caller ID edit
Set clock
Assign EXT#

 
						

							17
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Assigning the Extension Number
Assign the extension number to the unit to use the intercom feature.
Make sure that the unit has been connected to other units (KX-TS3282W 
and/or KX-T3281W) in parallel (p. 11-13) before programming.
Make sure that the handset is on the cradle, the AC adaptor is 
connected and the SP-PHONE/HEADSET indicator light is off.
1Press [FUNCTION/EDIT].
2Scroll to “Assign EXT#” by pressing [] 
or [].
3Press [].
•The numbers (1 to 8) that have already 
been assigned to other units are not 
displayed.
4Press [] or [] to move the cursor to 
select the extension number (1 to 8).
5Press [ENTER] (Save key).
•A beep sounds.
•The extension number ([1] to [8]) is shown on the 
right.
•You can exit the programming mode any time by pressing [EXIT].
•To change the extension number, start from step 1. The previous memory will be 
erased.
•To exchange the extension numbers between two units, erase each number (see 
below), then re-assign the number to each unit.
To erase the extension number
Repeat steps 1 to 3, and select “Erase” by pressing []. Press [ENTER] 
(Save key).
•“Extension# Not assign” is displayed. 
•All extension indicators flash until you assign a number to the unit.
After you connect the AC adaptor (p. 10), all of the extension indicators flash 
until you assign the extension number of your unit. Even if you do not use the 
intercom, assign the number. Otherwise all of the extension indicators will 
continue flashing.
 –––––––––––––––
Save M1,M2,M3
Save directory
Set clock
Assign EXT#
 –––––––––––––––
 Extension#
 12345678 Erase
     ENTER=Save
 

 Extension#
               1
Ex. Extension number 1
 
						

							Programmable Settings
18
What the extension indicators mean
Memory card
Remove the memory card and use it as a name index for extensions.
Off The extension is not in use.
On The extension is in use.
Cover
Memory Card 
						

							19
Preparation
For assistance, please call: 1-800-211-PANA(7262)
Programming Summary
You can program the following functions from the menu. After pressing 
[FUNCTION/EDIT], the main menu will be displayed first. If the main menu 
item has the sub-menu, it will be displayed. See the corresponding pages 
for function details.
Make sure that the handset is on the cradle, the AC adaptor is connected 
and the SP-PHONE/HEADSET indicator light is off.
During programming
•To select a desired function item, scroll through the menu by pressing [] or []. 
Then press 
[] to go to the next step.
•“
–––––––––––––––” indicates the beginning or end of the function menu.
•You can exit the programming mode any time by pressing [EXIT].
•If you do not press any buttons for 60 seconds, the unit will exit the programming 
mode.
Press [FUNCTION/EDIT].

 –––––––––––––––
Save M1,M2,M3 . . . . . p. 44
Save directory . . . . p. 38
LCD contrast . . . . . . p. 21
Ringer setting
Change password . . . p. 56
Dial setting
Line setting
Caller ID edit . . . . p. 35
Set clock. . . . . . . . . . p. 15
Assign EXT# . . . . . . . p. 17
 –––––––––––––––
•Scroll to a desired item by pressing 
[] or [], and press 
[].

 –––––––––––––––
Ringer volume . . . . . p. 22
Ringer pattern . . . . p. 23
Incoming call . . . . . p. 54
 –––––––––––––––
 –––––––––––––––
Set dial mode . . . . . p. 20
Set flash time . . . . p. 53
Call restrict . . . . . p. 58
 –––––––––––––––
 –––––––––––––––
Line selection . . . . p. 55
Call barge in . . . . . p. 60
 –––––––––––––––




 
						

							Programmable Settings
20
Dialing Mode
If you have touch tone service, set to Tone. If rotary or pulse service is 
used, set to Pulse. Your phone comes from the factory set to Tone.
Make sure that the handset is on the cradle, the AC adaptor is connected 
and the SP-PHONE/HEADSET indicator light is off.
1Press [FUNCTION/EDIT].
2Scroll to “Dial setting” by pressing 
[] or [].
3Press [].
4Press [] at “Set dial mode”.
•The current setting is displayed.
5Select “Pulse” or “Tone” by pressing 
[] or [].
6Press [ENTER] (Save key).
•A beep sounds.
•To exit the programming mode, press 
[EXIT].
•You can exit the programming mode any time by pressing [EXIT].
 –––––––––––––––
Save M1,M2,M3
Save directory
 Change password
Dial setting
Line setting
 –––––––––––––––
Set dial mode
Set flash time

 Dial mode
          :Tone
     ENTER=Save