Panasonic Hdtv Projection Monitor Pt 53tw54 Operating Instructions

							OPTIONAL EQUIPMENT CONNECTIONS
9 z
ENGLISH
Program Out Connection (PROG OUT)
To use the television audio and video with optional equipment,
connect the PROG OUT and TO AUDIO AMP connections on the
back of the television.
Note:If the Main Picture signal is Component Video Input or
HDMI, no Program out signal will be available.    
Procedure
• Connect optional equipment to PROG OUT and TO
AUDIO AMP L/R terminals.
• PROG OUT terminal display is the same as on-screen
display.
• See optional equipment manual for further instructions
for recording and monitoring.
HDMI (High Definition Multimedia Interface)
input connection
About HDMI
HDMI is the first all digital consumer electronics A/V
interface that supports several uncompressed standards,
enhanced and high definition video formats as well as
existing multi-channel audio format. One jack supports both
video and audio information. The HDMI/HDCP
1 input can
be connected to an EIA/CEA 861
2compliant consumer
electronic device, such as a set top box or DVD player
equipped with an HDMI or DVI output connection. By
inputting a High-bandwidth Digital Content Protection
(HDCP) high definition picture source to the HDMI terminal
of this PTV, high definition pictures can be displayed on the
screen in their digital form. The HDMI input terminal is not
intended to be used with personal computers. This PTV is
compatible with 1080i, 480p and 480i formats. Select the
output of the connecting device to match that of the PTV.
Notes:
1. HDMI/HDCP = High Definition Multimedia Interface /
High-Bandwidth Digital Copy Protection.
2. EIA/CEA-861 Profiles compliance covers profiles for
transmission of uncompressed digital video including
high bandwidth digital content protection.
Compatible formats
Connection diagram
Follow the diagram below to connect the PTV to a set top box or a
DVD player. 
Procedure
• Connect the HDMI output from the set top box or a DVD
player to the HDMI input on the back of the PTV.
• Press TV/VIDEO button on the remote control to select
HDMI input. The interface on the PTV is an HDMI Type A
connector.
• If the external device has a DVI output only, use a DVI to
HDMI adaptor cable*
3 to connect to the HDMI jack on
the PTV. Also, connect the Audio Out signal from the
external device (set top box or DVD player) to the Audio
In*
4 jacks below the HDMI input.
• If you cannot display the picture because your Digital Set
Top Box does not have a Digital Out terminal setting, use
the Component Video Input (or the S-Video Input or
Video Input). In this case, the picture will be displayed as
an analog signal.
Notes:
*3. HDMI-DVI conversion cable (TY-SCH03DH) available
on Panasonic Website: www.panasonic.com.
*4. Please refer to page 20 for Audio setting detail.
AUDIO
   IN L
RANT 
CABLES NOT INCLUDED
TERMINALS ON BACK OF TELEVISION
S-VIDEO
COMPONENT 
VIDEO INPUTVIDEO
12
INPUT
PROG
OUTTO AUDIO 
AMP
VIDEOY
PB
PR

L
R
AV IN
231
HDMI
INPUT INPUT
VCR
OR MONITOR
This PTV is compatible with the following formats. Please 
set the connecting device to the following format.
Video signal   
Audio signal
When digital audio is included in the HDMI connection, 
the compatible sampling frequencies are 48 KHz / 
44.1Khz / 32 Khz.
FormatNo. of dotsVertical scanning 
frequency (Hz)
1080i 1920 x 1080i 59.94 / 60
480i (480p)720 x 480p
640 x 480p59.94 / 60
59.94 / 60
480i (480i) 720 x 480i 59.94 / 60
Incoming
Cable
EXTERNAL DIGITAL
    COMPONENT
 AUDIO  OUTLRHDMI 
OUT
Note: Use anolog audio when no digital
audio is available.
AUDIO
   IN L
RANT 
CABLES NOT INCLUDED
TERMINALS ON BACK OF TELEVISION
S-VIDEO
COMPONENT 
VIDEO INPUTVIDEO
12
INPUT
PROG
OUTTO AUDIO 
AMP
VIDEOY
P
B
PR

L
R
AV  I N
231
HDMI
INPUT INPUT
* The connector on the PTV is HDMI Type A connector. 
						

							10 z
SPECIAL FEATURES
ENGLISH
Special Features
ASPECT Button 
The ASPECT button on the remote control lets you choose
one of four display modes, depending on the formats of the
received signal and your preferences. 
BBE Button
Press this button to turn BBE sound feature On or Off.
SAP Button
Press this button to let you cycle through different audio modes.
For example:
• If receiving STEREO, SAP and MONO or receiving
STEREO and MONO only, pressing SAP button will
toggle the audio as follows:  
Split Operation
This feature lets you watch two different channels side by
side with or without an external video source.
Procedure
• Press   to display Split frame.
• Choose channels for the SPLIT frame by pressing
 button. The right indicator ( ) will appear
in Split frame, then use  or the remote
control numeric keypad.
Note:Split frame channel can only be change while right
indicator ( )is displayed in split frame. 
• Select channels for the Main picture by pressing
or use the remote control numeric keypad.
• Press  to switch the SPLIT FRAME and MAIN
PICTURE source.
• Press  to view picture source status.
• Press   to cancel Split frame.
Split Operation With a Cable Box
To view premium (scrambled) cable channels through your
cable box in the Main Picture:
Note:Use this procedure if you want to watch premium cable
channels in the Main Picture while viewing a television
program or video in the Split frame.
Procedure
• Tune TV to Channel 3.
• Press   on the remote control to display Split
frame.
Note:Audio is from the Main Picture only.
• Verify that the Cable box is ON.
• Choose channels for the Main Picture by tuning the
cable box.
• Choose channels for the SPLIT frame by pressing
 button, then use  or the remote
control numeric keypad.
Note:Swap is not available when using the cable box to tune
channels. If your cable box has video output, it can be
connected to the TV to allow you to use all SPLIT
functions.  Customer Options depending on Component Input Signal
INPUT
SIGNAL  DISPLAY ON SCREENASPECT BUTTON 
OPTIONS
1080i16:9 onlyNo options
480i (16:9)Default to 16:94:3, Full or Zoom (see 
below)
480i (4:3)Default to FULL mode.
 Note: Will stretch picture 
horizontally.4:3, Full or Zoom (see 
below)
480iDefault to JUST mode4:3, Full, Just or 
Zoom (see below)
Input SignalASPECT
4
3
Image on 
16:9 Screen Size
4:3
480i or 480p
This will display a 4:3 picture
at its standard 4:3 size with
gray side bars. (Not
recommended for viewing
4:3 pictures as it  may create
a permanent image on
screen if displayed for a
prolonged period of time.)
480i  or 480p
Input SignalASPECTImage on 
16:9 Screen Size
ZOOM
16
9
This will expand the 4:3 
picture uniformly (width and 
height) to full screen width 
and then reposition the 
picture vertically. 
(Recommended for letterbox 
pictures.)
480i  or 480p
Input SignalASPECTImage on 
16:9 Screen Size
FULL
16
9
This will show picture at full 
screen size. (Recommended 
for anamorphic pictures.)
Input SignalASPECTImage on 
16:9 Screen Size
480i
JUST
16
9
This will stretch the right and 
left edges of a 4:3 picture to 
fill the screen, The center of 
the screen will have aspect 
correction applied. The size 
of the picture will depend on 
the original signal. 
(Recommended for regular 
TV viewing.) Note:If menu is displayed while in Zoom mode, the aspect
will change to Full to display complete menu.
STEREO JSAP JMONO
SPLIT
SPLIT CTRL
or
CHCH
Change Main Picture channel Change Split Frame channel
or
CHCH
SWAP
RECALL
SPLIT
SPLIT
SPLIT CTRLor
CHCH 
						

							SPECIAL FEATURES
11 z
ENGLISH
Split Operational Buttons
SPLIT  CTRL Button  
Pressing   will enable you to use   or
numeric keys for changing split channel and to use TV/
VIDEO button to select desired input for split frame.
TV/VIDEO Button   
Press when Split frame is displayed to select desired input
mode. 
Procedure
• Press    to display Split frame.
• Press   to use remote control for split
operation.
• Press   to display video input menu.
• Press corresponding number key on the remote control
to select the input of your choice.
Note:Split frame input mode can only be change while right
indicator ( )is displayed. 
 
Search Button 
This feature lets you scan through all available channels.
Procedure
• Press    to display split frame.
• Press   to display search frames.
• Press  again to stop search feature. Split
frame channel will be the last active search frame.
• Press   to cancel split frame.    
Note:When main picture is component or HDMI signal, Search
feature is not available.
Freeze Button 
This feature is used to stop action in Split frame.
Procedure
• Press   to display split frame.
• Press   to stop split frame action. • Press   again to continue action. 
• Press   to cancel frame.      
Main Picture Freeze Feature
This feature is used to stop action of the Main Picture and
display it on a Split freeze frame.
Procedure
• To stop action for Main picture, press   while
Split frame is not displayed.
• Main Picture freeze will be displayed in Split frame. 
• Press   again to cancel Main Picture freeze
frame.
Note:While Main Picture freeze frame is displayed, only
FREEZE button is active for split frame. All other Split
buttons have no effect.
Direct Video Input Selection
This feature lets you select video inputs directly using the
TV/VIDEO button and the numeric keys on the remote
control.
Procedure
• Press   on the remote control to display the
Input selection menu.   
• Press corresponding number key on the remote control
to select the input of your choice.
Note:Video input can also be selected by pressing TV/VIDEO,
then the CH STbuttons.
SPLIT CTRLor
CHCH
SPLIT
SPLIT CTRL
TV/VIDEO
Main Picture
TV
SPLIT FrameCOMPONENT1COMPONENT2
HDMI-IN
VIDEO 1/2/3/4
SPLIT
SEARCH
SEARCH
SPLIT
2
3
4
Search Frames Main Picture
SPLIT
FREEZE
FREEZE
SPLIT
Main Picture
Split freeze frame
FREEZE
FREEZE
TV/VIDEO
1  TV
2  COMPONENT1
3  COMPONENT2
4  HDMI
5  VIDEO1
6  VIDEO2
7  VIDEO3
8  VIDEO4 
						

							12 z
REMOTE CONTROL OPERATION
ENGLISH
Remote Control Operation  
EUR7603ZF0
               
Press to turn ON and OFF.
POWER
MUTE
Press to mute sound. Press to display and
cancel CC (Closed Caption).
Press to select remote operation.
 V
CR
 DV
D
   
T
V
 CBL D
BS
 A
UX R
CV
R
 D
TV
ACTION
Press to access menus.
Press to adjust TV sound and navigate in 
menus.
VOL  VOL
Press numeric keypad to select any channel.
7
4
12
5
8
0
9
6
3
R-TUNE
Press to switch to previously viewed 
channel or input modes.
EXIT
Press to exit PTV and DBS menus.
BBE
MENU
BBE - Press to turn on or off.
MENU - Press to access DBS or DVD menus.
SAP
 
Press to access audio modes (Stereo, SAP 
or Mono).
TV/VIDEO
Press to select TV or input modes for main 
picture or split frame.
Note:Refer to TV/VIDEO Button section on
page 11 for selecting split frame input. 
Press to select next or previous channel and 
navigate in menus.
CH
CH
GUIDE 
DBS functions button.
*SWAP
REW*SPLIT
PLAY**SPLIT CTRL
FF
*FREEZE
PAUSE*SEARCH
STOPREC
TV/VCR
*(FREEZE)
 DVD/VCR CHOPEN/CLOSE
*(SEARCH)
*Split function buttons
Component function buttons
X
PROG  
Press to enter minor number in a compound 
number.
RECALL    
Press to display time, channel, sleep timer, 
and other options.
PA G E
DBS page up/down and DVD skip -/+
buttons. 
LIGHT  
Press to illuminate remote buttons.
ASPECT  
Select picture size (ratio) to match 
programming format. 
**While split frame is displayed press 
button: right indicator   will be displayed in split
frame. Then use CHS/CHT or numeric keypad
to change channels and TV/VIDEO to select input
for split frame.SPLIT CTRL 
						

							REMOTE CONTROL OPERATION
13 z
ENGLISH
Operating Components with Remote Control
Note:Refer to page 15 for programming Remote Control
procedure.
Operating a VCR
Program the remote control to use with VCR.
Operating a DBS
Program the remote control to use with DBS.Operating a DVD
Program the remote control to use with DVD  
Operating a CD
Program the remote control to use with CD. 
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offRewind the
TapeREW
Select TV Input
mode for VCRFast ForwardFF 
Change Channels
up/downSelect a Channel
Change Channels
up/downDVD/VCR CHPausePA U S E
RecordRECChange to TV or
VCR ModeTV/VCR
PlayPLAYOn screen VCR
Display RECALL
StopSTOP
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offNavigation 
left/right
STB Audio track  SAP
 STB ActionACTION
Navigation 
up/downSelect a
Channel 
STB Change
Channels up/downDVD/VCR CHPrevious
ChannelR-TUNE
STB AspectASPECTSTB page 
up/down PA G E  
STB MenuMENUSTB guideGUIDE
STB ExitEXITSTB searchOPEN/CLOSE
STB program  infoRECALLSTB select
dash channelPROG  
STB FAVPLAYSTB M. guideSWAP 
STB RecordRECSTB jumpFF 
Change to TV or
SAT ModeTV/VCR
POWER
TV/VIDEO
CH
CH7
4
12
5
8
0
9
6
3
X
POWERVOL  VOL
CH
CH7
4
12
5
8
0
9
6
3
X
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offSkip searchFF 
Navigation 
up/downSelect chapter
Ch -/+DVD/VCR CHPausePAUSE
RecordRECSelectACTION
PlayPLAYDVD DisplayRECALL
StopSTOPMenuMENU
Open/CloseOPEN/CLOSETitleGUIDE
Skip -/+PA G E  
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offPlayPLAY
Time formatRECALLNext diskGUIDE
Next/previous
trackSelect Tracks
Random / repeat.DVD/VCR CHNext diskR-TUNE
Search FFFF Search RewREW
Skip -/+PA G E  Still/pausePA U S E
StopSTOPOpen/CloseOPEN/CLOSE
POWER
VOL  VOL
CH
CH
7
4
12
5
8
0
9
6
3
X
POWERX
CH
CH
7
4
12
5
8
0
9
6
3 
						

							14 z
REMOTE CONTROL OPERATION
ENGLISH
Operating a DTV Set Top Box
Program the remote control to use with DTV. 
Operating a Receiver
Program the remote control to operate audio receiver.
Operating a PVR (Personal Video Recorder)
Program the remote control to use with a PVR.   Operating a Cassette Deck
To operate a cassette deck, the remote control must be in
AUX mode and be programmed with the appropriate code
for your equipment.
Operating a CABLE BOX
Program the remote control to use with Cable Box. 
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offProgram
InformationRECALL
SAPSAP
 GuideGUIDE
Navigation
up/downSelect
Channel
Navigation
left/rightSelect dash
numberPROG  
AspectASPECTRecordREC
DTV ActionACTIONMenuMENU
ExitEXIT
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offVo l u m e  + / -
Audio MuteMUTETo select AV input
or Components
Press Remote 
numeric keypad 
Switch inputSurround -REW
Tuner +/-Surround +FF 
Center-/+DVD/VCR CH
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offRewind REW
Select TV/VCRFast ForwardFF 
PVR up/downSelect a Channel
POWER
CH
CH
7
4
12
5
8
0
9
6
3
VOL  VOL
POWERVOL  VOL
AV I P r e s s  1
AV 2 P r e s s  2
AV 3 P r e s s  3
AV 4 P r e s s  4
CD Press 5
TUNER Press 6
PHONO Press 7
TAPE Press 8
AUX Press 9
TV/VIDEO
CH
CH
POWER
TV/VIDEO
CH
CH7
4
12
5
8
0
9
6
3
PVR left/rightPausePAUSE
Change
Channels
up/downDVD/VCR CHReplay zoneR-TUNE
PVR selectACTIONInstant replayTV/VCR
RecordRECReturn to livePROG  
PlayPLAYQuick skipOPEN/CLOSE
StopSTOPReplay guideGUIDE
MenuMENUExitEXIT
EnterRECALL
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offRewind REW
RecordRECFast ForwardFF 
PlayPLAYPausePAUSE
StopSTOPOpen/CloseOPEN/CLOSE
Deck A/BR-TUNE
TO DO THIS...PRESSTO DO THIS...PRESS
Turn on/offVo l u m e
up/down
Audio MuteMUTEEnterACTION
Change
Channels
 up/downSelect a
Channel
Change Channels
up/downDVD/VCR CHPrevious
ChannelR-TUNE
TO DO THIS...PRESSTO DO THIS...PRESS
VOL  VOL
X
POWER
X
POWERVOL  VOL
CH
CH7
4
12
5
8
0
9
6
3 
						

							REMOTE CONTROL OPERATION
15 z
ENGLISH
Programming The Remote Control
The Universal Remote Control can be programmed to
operate many manufacturers’ components using the
component function buttons for VCR, DVD, AUX, RCVR,
TV, DTV CABLE or DBS. Follow the procedures for
programming your Remote Control with or without a code
for the component.
Note:Determine the manufacturer of the component and look
in the table for the code (found on page 16 and 17).
Procedure
1. Confirm that the external component is plugged in and
operating.
2. Turn the component off.
3. Press  and  together for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote
Control: 
VCR, DVD (CD), AUX (VCR2 or TAPE),
RCVR, DTV, CABLE or DBS.
 The component button
will illuminate steadily and all others will go out.
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
6. Press the Remote Control   to test the
component. If the procedure was successful, the
component will turn on and the component key will blink
twice and then go out.
Note:If the component does not operate with the Remote
Control, repeat the steps 3 through 6 using another code
(some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Programming Without A Code
This procedure searches all codes and is called the
“sequence method.”
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
3. Press  and  together, for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press the appropriate component button on the Remote
Control. The component button will illuminate steadily
and all others will go out.
5. Press the   button to set the remote control to the
step and set mode.
6. Point the remote control towards the component.
7. Press VOL X(the mode key will blink three times), then
press the Remote Control   button to test the
component. Continue this process until the proper code
is found. If the procedure was successful, the component
will turn on.
Note:Each time you press the VOL X button, make sure that the
component key blinks twice before pressing the POWER
button.
8. Once the device responds, press   to store the
code. The mode (component) button will blink twice.
Note:It may take many attempts before the correct code
is found. If you miss a code, press WVOL, then press
the   button to test the component.
Component Codes
The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model. Default Modes for Remote Control
DeviceOperatesDefault
TVTV (Panasonic Only)Panasonic TV Code
DTV-STBDTV (Panasonic Only)Panasonic DTV Code
CABLECABLE (Preset)Panasonic CABLE 
Code 
DBSDBS (Preset) Panasonic DBS Code
VCRVCR (Preset)Panasonic VCR Codes
DVD/CDDVD and CD (Preset)Panasonic DVD Codes
AUXPersonal Video Recorders, 
Tape and VCR2Panasonic Personal 
Video Recorder Code
RCVRAudio receiver (Preset)Panasonic RCVR code
ACTIONPOWER
POWER
Write the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.
     VCR DVD DVD (CD)  
AUX (VCR2)  AUX (TAPE)  RECEIVER  
DTV  CABLE  DBS  
ACTIONPOWER
POWER
POWER
ACTION
POWER 
						

							16 z
REMOTE CONTROL OPERATION
ENGLISH
Component codes 
Codes For VCR   
BrandCode
Admiral335
Aiwa332
Akai314, 315, 316, 329
Audio 
Dynamic311, 339
Bell & How-
ell305, 313
Broksonic320, 326
Canon323, 325
CCE343
Citizen306
Craig305, 306, 329
Curtis 
Mathes324, 345
Daewoo 301, 324, 343
DBX310, 311, 339
Dimensia345
Emerson303, 319, 320, 
325, 326, 343
Fisher305, 307, 308, 
309, 313
Funai320, 326, 334
GE324, 333, 345
Goldstar306
Gradiente334
Hitachi300, 323, 345
Instant 
Replay323, 324
Jensen339
JVC310, 311, 334, 339
Kenwood306, 310, 311, 339
LXI300, 305, 
306,307, 308, 309
Magnavox323, 324, 331
Marantz310, 311, 339
Marta306
Memorex309, 324
MGA338, 340, 341, 
347,348
Minolta300, 345
Mitsubishi338, 340, 341, 
347, 348
Multitech304, 347
NEC310,311, 334, 339
Olympic323, 324
Optimus306, 321, 328, 335
Orion320, 326
Panasonic321,322, 323, 324
Codes For VCR (Contd.)
BrandCode
Penney300,305, 310, 311, 
324, 339, 345 
Pentax300,311, 345
Philco320, 323, 324, 
326, 331, 343
Philips323, 324, 331
Pioneer323
Proscan300, 301, 302, 
323, 324, 331, 
333, 345, 346
Quasar321, 322, 323, 324
Radio Shack305, 309, 324, 
333, 336, 340
RCA300, 301,302, 
323, 324, 331, 
333, 345, 346
Realistic305, 309, 324, 
336, 340
Samsung302, 304, 333
Sansui320, 326, 339, 352
Sanyo305, 309, 313
Scott301, 302, 304, 
309, 320, 326, 
338, 340, 347, 348
Sears300, 305, 306, 
307, 308
Sharp335, 336
Shintom317
Signature 
2000335
Singer337
Sony328, 329, 330
Sylvania323, 331, 324 
Ta s h i r o306
Tatung310, 311, 339
Teac310, 311, 339
Technics321, 322, 323, 324
Te k n i k a324
To s h i b a301, 346
Ve ct o r 
Research311
Wards306, 309, 335, 
336, 344
Ya m a h a305, 310, 311, 339
Zenith306,344
Codes For Cable Box
BrandCode
ABC124
Archer125, 132
Cableview105, 132
Citizen105,122
Curtis112, 113
Diamond124, 125, 132
Eagle129
Eastern134
GCbrand105, 132
Gemini122
General
Instrument/
Jerrold111, 119, 120, 
121, 122, 124, 
125, 126,127
Hamlin112, 118, 140, 
141, 142, 145
Hitachi103, 124
Macom103, 104, 105
Magnavox133
Memorex130
Movietime105, 132
Oak102, 137, 139
Panasonic109, 110, 114
Philips106,107, 128, 
129, 130
Pioneer101, 116
Pulsar105, 132
Puser132
RCA11 5
Realistic132
Regal112, 118, 140, 
141, 142, 145, 
Regency134
Rembrand105, 132, 137
S.A.111, 112, 113
Samsung105
Scientific 
Atlanta111, 112, 113
Slmark101, 105
Sprucer105, 110
Stargate105, 132
Te l e v i e w101, 105
Texscan144
To c o m135
To s h i b a104
Unika125, 132
Universal122, 132
Videoway106
Viewstar129, 130
Zenith100, 117
Zenith/.Drake 
Satellite100
Codes For DBS  
BrandCode
Dish Network 
(Echostar)105, 115, 116
Echostar105
Express VU105, 115
G.  E .106
G.I. (General 
Instrument)108
Gradiente11 4
Hitachi103, 111, 
11 2
HNS (Hughes)103
Magnavox101, 102
Panasonic104
Philips101, 102
Primestar108
Proscan106, 109, 110, 
11 3
RCA106, 109, 
11 0 ,  11 3
Sony107
Star Choice103, 108
To s h i b a100
Uniden101, 102
Zenith127
Codes For DVD
BrandCode
Denon100
Ferguson101
JVC109
Mitsubishi105
Nordmende101
Panasonic100
Philips103
Pioneer102
RCA101
Saba101
Samsung11 0
Sharp108
Sony104
Technics100
Thomson101
To s h i b a103
Yamaha100
Zenith107 
						

							REMOTE CONTROL OPERATION
17 z
ENGLISH
Component Codes (Cont.)
Codes For Cassette Decks   
BrandCode
Aiwa223, 224, 225
Denon231
Fisher203
Jensen214
JVC229, 230
Kenwood200, 207
Marantz202
Nakamichi205
Onkyo208, 209, 213
Panasonic216, 218
Philips222
Pioneer204
RCA226, 227, 228
Sansui205, 210
Sharp231
Sony219, 220
Te a c210, 211, 215
Technics216, 218
Ya m a h a201, 202
Codes For Receivers 
BrandCode
Admiral120
Aiwa125, 126
Denon134, 135, 136
Fisher104
Garrard11 3
Harman 
Kardon11 5 ,  1 2 3
Jensen129
Codes For Receivers 
(cont.) 
BrandCode
JVC132, 133
Kenwood100, 108
Magnavox127
Marantz124
Mclntosh11 6
Nakamichi106
Onkyo109, 114
Optimus103, 127, 130, 
131
Panasonic118, 119, 121
Philips123
Pioneer105, 107
Quasar118, 119, 121
RCA103, 105, 127, 
130, 131
Sansui103, 111, 139
Sharp134, 137
Sony122
Soundesign138
Te a c111 ,  11 2 ,  11 3
Technics118, 119, 121
Victor132, 133
Ya m a h a101, 102
  
Codes For CD Player  
BrandCode
Admiral226
Aiwa233, 235
Carver229
Denon242
Emerson239
Fisher205
Harman/Kardon219, 220, 
221, 223
Hitachi207
Jensen234
JVC240, 241, 245
Kardon223
Kenwood200, 201, 211, 
245
LXI/Sears236
Magnavox229, 232
Marantz229
McIntosh221
Nakamichi210
Onkyo214, 215
Optimus208, 218, 
220, 222
Panasonic224, 225, 227
Philips229, 230
Pioneer208
Quasar224, 225, 227
RCA231, 237, 
238, 247
Sansui210, 246
Sanyo205
Scott210, 246
Sharp242, 243
Sherwood220
Sony228
Soundesign244
Te a c212, 216, 218
Technics224, 225, 227
Victor240, 241, 245
Ya m a h a202, 203, 204
Codes For Personal Video 
Recorders
BrandCode
Panasonic Replay 
TV100
Philips Tivo102
Sony Tivo101 
						

							18 z
BASIC MENU NAVIGATION
ENGLISH
Basic Menu Navigation
EXIT
Press
Press
Press
Press to select OTHER ADJ.to display the
Main Menu.
to choose the 
desired icon.
sub Menu
Field
Press
Press to exit Main Menu.
NORMAL PICTURE
EXIT
Press to enter the sub-
menu field.
PICTUREPIC MODE
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
OTHER ADJ.
PRESS ACTION FOR MAIN MENU
VIVID
- - - - - - - - - - - - - - - - I- - - - - - - - - - - - - - - -I I I I I I I I I I I I I I II I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I II I I I I I I I I I I I I I I I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
I I I I I I I I I I I I I I I I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
NO
PICTUREPIC MODE
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
OTHER ADJ.
PRESS ACTION FOR MAIN MENU
VIVID
- - - - - - - - - - - - - - - - I- - - - - - - - - - - - - - - -I I I I I I I I I I I I I I II I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I II I I I I I I I I I I I I I I I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
I I I I I I I I I I I I I I I I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
NO
PICTUREPIC MODE
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
OTHER ADJ.
PRESS ACTION FOR MAIN MENU
VIVID
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I 
NO
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - l
- - - - - - - - - - - - - - - - - - - - - l - - - - - -
Pressto select desired
sub-menu.PICTUREPIC MODE
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
OTHER ADJ.
PRESS ACTION FOR MAIN MENU
VIVID

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I 
NO
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - l
- - - - - - - - - - - - - - - - - - - - - l - - - - - -
to select or adjust
desired sub-menu.
BRIGHTNESS  32  ----------I--------- 
Note: For sub-menu with OTHER ADJ. 
PICTUREPIC MODE
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
OTHER ADJ.
PRESS ACTION FOR MAIN MENUPRESS X to ENTER
Press to enter sub sub-menu
field.
Pressto select desired sub
sub-menu.PICTURE
PRESS ACTION TO  RETURNOTHER ADJ.COLOR TEMP
NATURAL COLOR
VIDEO NR
3D Y/C FILTER
COLOR MATRIX
VM
MPEG NR
NORMAL
ON
OFF
ON
SD
ON
OFF
PRESS      FOR MORE
Pressto select or adjust
desired sub sub-
menu.PICTURE
PRESS ACTION TO  RETURNOTHER ADJ.COLOR TEMP
NATURAL COLOR
VIDEO NR
3D Y/C FILTER
COLOR MATRIX
VM
MPEG NR
WA R M
ON
OFF
ON
SD
ON
OFF
PRESS      FOR MORE
Note: To EXIT menus.   
repeatedly until Main Menu
Icon is highlighted.EXIT
Main Menu Icon
sub sub-Menu
Field
PICTURE
PRESS ACTION TO  RETURNOTHER ADJ.COLOR TEMP
NATURAL COLOR
VIDEO NR
3D Y/C FILTER
COLOR MATRIX
VM
MPEG NR
NORMAL
ON
OFF
ON
SD
ON
OFF
PRESS      FOR MORE
PICTUREPIC MODE
COLOR
TINT
BRIGHTNESS
PICTURE
SHARPNESS
NORMAL
OTHER ADJ.
PRESS ACTION FOR MAIN MENU
VIVID
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ I 
NO
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - -I- - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - l
- - - - - - - - - - - - - - - - - - - - - l - - - - - -