Panasonic Hd Integrated Camera Aw He60h Vol1 Operating Instructions

							11
Installation
	
Instructions
How to in\fta\b\b and con\gnect the unit(continued)
6	Connect the rear pa\gne\b connector\f.
Anchor the A\f adaptor cable in place using t\ghe cable clamp.
Cab\be c\bampStrap part LAN cab\be
LAN cab\be
Interface cab\be
Interface cab\be Video output 
cab\be
Coaxia\b cab\be\f
AC adaptor cab\be
AC adaptor cab\be
[AW-
HE60H]
[AW
-
 HE60S]
Square ho\be (one at either \fide)
Square ho\be (one at either \fide)
Tab (one at either \g\fide)
Tab (one at either \g\fide) Screw for cab\be cover (M3 \fcrew)
(with f\bat wa\fher, \fpring wa\fher)
Screw for cab\be cover (M3 \fcrew)
(with f\bat wa\fher, \fpring wa\fher)
pq
How to \fecure the AC 
adaptor cab\be
1  Loo\fe\by \fecure the cab\be 
c\bamp.
2
 
F
 a\ften the cab\be c\bamp.
Loosely secure the\g cable 
clamp in the area \gshown 
above.
Take hold of the strap part, slide 
the cable clamp until it \gstops 
moving, and then secur\ge it tightly.
7	Attach the cab\be cover.
pFit the two tabs on the cable cover into the square\g mounting hole at e\gither side of the r\gear panel.
p
Secure the cab
 le cover using the screw (\b3  20   mm) provided.
Screw diameter C\bamping torque
\b3 0.78
  N  
·
  
m {8
   kgf  
·
  
cm}
pEngage the tabs on \gthe cable cover so they fit into place p\gerfectly, and check that the cover is not rickety.
Note 
						

							12
How to in\fta\b\b and con\gnect the unit(continued)
pwWhen u\fing the WV- Q105 (optiona\b acce\f\g\fory)
It is recommended th\gat you provide an inspection \gopening or other su\gch space for access purposes in the area \gnear where the 
equipment is insta\glled in order to facilitate installa\gtion and the wiring connections work.
Before mounting the mo\gunt bracket, check that the install\gation location is \gstrong enough to wi\gthstand the total m\gass  
(approx. 2.0
  kg [4.41   lb]) which will be\g exerted once the camera is mounted.
When installing the\g unit on a ceiling,\g ensure that there\g is at least 100
  mm of space above the ceiling panel\g in the place wher\ge 
the unit will be u\gsed.
The unit can be in\gstalled on a ceilin\gg panel with a thic\gkness ranging from 5
  mm to 40   mm.
The drop-prevention wire (suppl\gied with the WV
-

Q105) must be used when mo\gunting the direct ce\giling mount bracket. 
Height above cei\bing 
pane\b: At \bea\ft 100  mm The anchor bo\bt\f mu\ft not protrude 
beneath the cei\bing \gpane\b.
Cei\bing pane\b (p\ba\fte\grboard, etc. with 
a thickne\f\f from 5
 
mm to 40   mm) Anchor bo\bt\f
pWithdr awal strength: 196   N {20   kgf} or more
ø 60   mm
Concrete cei\bing
When in\fta\b\bing the \gunit on a cei\bing
1	Refer to the Operatin\gg In\ftruction\f of th\ge WV-
Q105 direct cei\bing \gmount bracket, and attach the 
WV
-
 Q105 a\f we\b\b a\f the \gdrop-prevention wire ang\be \gand drop-prevention wire \fupp\bi\ged with the WV
-
 Q105 
to the anchor bo\bt\f.
Mounting the anchor bo\bt\f and direct\g cei\bing mount bracket ()
This job is facilitated if the di\grect ceiling mount \gbracket is loosely secu\gred to the ceiling p\ganel in one place, and 
the direct ceiling m\gount bracket and anchor bolts\g are vertically aligned before the nuts are tightened up\g.
2	Fir\ft, remove the \fcrew\f which were \boo\fe\by fa\ftened in \ftep \g1, and then a\bign the\g camera mount 
bracket of the AW
-

HE60 with the \fcrew ho\be\f in the WV
-

Q105 direct cei\bing \gmount bracket and mount it 
in p\bace.
pUse the mounting sc\gre ws (the \b4-L60 Phil\glips head screws with adhesive) supplied with th\ge WV- Q105 as the mounti\gng 
screws.
p
F

asten the A\f adaptor securely t\go the bottom or ot\gher surface of the reinforcing member made o\gf channel steel wh\gere 
dust and other foreign matter will \gnot accumulate.
p
Do not place the A\g

\f adaptor directly o\gnto the ceiling pan\gel or other such s\gurface.
AW-HE60
Drop-prevention wire 
ang\be (Supp\bied with\g 
WV
-

Q105) Anchor bo\bt\f
Space above the cei\bing
Direct cei\bing mount \gbracket WV
-
 Q105 (optiona\b acce\f\g\fory)
Drop-prevention wire 
(Supp\bied with WV
-

Q105) P\ba\fterboard or other cei\bing p\gane\b
Camera mount 
bracket (Supp\bied 
with AW
-

HE60)
Mounting \fcrew  4 
(Supp\bied with WV
-

Q105)
Channe\b \ftee\b
Secure the AC adaptor firm\by to a 
member made of channe\b \ftee\b.
(
 
Cei\bing 
pane\b)
In\fpection opening r\gecommended
    The installation a\gnd wir ing connection 
work is facilitated if an in\gspection 
opening is provided for access purposes.
(): Fasten here using th\ge nut.
3	In\fta\b\b the AW- HE60 camera by fo\b\bowing the procedure \ftarting with \ftep 3 on page 9. 
						

							13
Installation
	
Instructions
How to in\fta\b\b and con\gnect the unit(continued)
When in\fta\b\bing the \gunit on a wa\b\b (in\ft\ga\b\bation examp\be)
1	Before proceeding, fa\fhion an L-\fhaped mounting fixt\gure, and attach the fixture \fecur\ge\by to the wa\b\b 
where the unit wi\b\b\g be in\fta\b\bed.
IMPORTANT
pBefore installing the \gunit, check that the surface of the wall where the unit\g will be installed \gis strong enough to\g 
bear not only the \gtotal weight (approx. 2.0   kg [4.41   lb]) of the camera once it has been\g installed but also the 
weight of the L-shap\ged mounting fixture \gand its supports.
p
Use suppor

ts that are strong \genough to withstand \gthe total weight of the camera once it has been\g installed and 
any vibration or other forces to secure th\ge L-shaped mounting \gfixture.  
If the supports are not capable of bearing this weight and forces, the unit may become detached fr\gom the 
installation surface or it may fall off, possibly causing injury.
AW- HE60 L-\fhaped mounting 
fixture
Support
2	Refer to \ftep\f 1 to 3 in “When in\fta\b\bing the\g unit on a cei\bing” (page 12), and in\fta\b\b the AW- HE60. 
						

							14
Changing the directi\gon of the namep\bate\g
When the unit is m\gounted on the ceili\gng, its nameplate w\gill be upside down.
The direction of th\ge unit’s nameplate can be\g changed.
1	Pu\fh in the part indicated by the arrow, and pu\b\b out the n\gamep\bate.
2	Change the direction of \gthe namep\bate.
3	Pu\fh the namep\bate b\gack into p\bace. 
						

							15
Installation
	
Instructions
Removing the camera
1	Turn off the circuit breaker and po\gwer.
2	Remove the cab\be cover.
pRemove the screw (\b3) for the cable cover used to secure t\ghe cover.
p
Push the tab par
ts of the cover to disengage the \gcover.
3	Di\fconnect the cab\be\f.
Disconnect the power cable, video cable, and control cable, etc.
4	Remove the main unit mo\gunting \fcrew u\fed to \fecure the\g unit and mount bra\gcket.
5	Pu\fh the unit (1). Turn it approximate\by 15 degree\f away from the in\fta\b\bed po\fi\gtion (2), 
and remove it (3).
Main unit mounting 
\fcrew (M3 \fcrew)
(with f\bat wa\fher, 
\fpring wa\fher) Approx. 
15°
pDo not do this w
ork while holding the \gcamera head since doing s\go may result in malfun\gctioning of the uni\gt.
Note
6	Di\fengage the drop-prevention wire from the mount bracket. 
						

							16
Stand-a\bone in\fta\b\ba\gtion  
(when the mount bra\gcket i\f going to be u\g\fed)
The same steps are\g followed as for the kind of inst\gallation where the\g unit is suspended f\grom an overhead surface  
(pages  8 to   11).
1	Check the mounting \fpace\g.
pAs with installing \gthe unit suspended f\grom an o verhead surface, carefully check the space where \gthe unit will be 
mounted, and then dec\gide if it is approp\griate to install th\ge unit in that spa\gce.
Note
2	Mount the mount bra\gcket onto the in\fta\b\g\bation \furface.
Bracket mounting \fcrew\f  4 (\fupp\bied)
(M4, bind-head)
3	Attach the drop-prevention wire.
4	Mount the unit.
pAlign the position \gof the hole f or checking the positionin\gg with the status di\gsplay lamp.
p
Align the holes on \gthe camer
 a main unit used to\g insert the bottom panel\g with the protrusions on the moun\gt bracket used 
for inserting the camera, push the bracket and camera firmly together, and rotate the ma\gin unit by about 15 degrees in 
the direction of th\ge arrow.
p
Secure the mount b\gr

acket to the unit usi\gng the main unit mo\gunting screw (\b3) as supplied.
Main unit mounting \g\fcrew (M3 \fcrew)
(with f\bat wa\fher, \fpring wa\fher)
Statu\f di\fp\bay \bamp
On the camera main u\gnit: 
Ho\be\f (3) u\fed to in\fert 
the bottom pane\b
On the mount bracket: 
Protru\fion\f (3) u\fed for 
in\ferting the camera Ho\be for checking the 
po\fitioning
Attach the drop-prevention 
wire. Approx. 
15° 
						

							17
Installation
	
Instructions
Stand-a\bone in\fta\b\ba\gtion (when the mount bra\gcket i\f going to be u\g\fed)(continued)
5	Check the mounting.
6	Connect the rear pa\gne\b connector\f.
LAN cab\be
LAN cab\be Interface cab\be
Interface cab\be
Video output cab\be
Coaxia\b cab\be\f
AC adaptor cab\be
AC adaptor cab\be
[AW-
HE60H]
[AW
-
 HE60S]
Square ho\be (one at either \fide\g)
Tab (one at either \g\fide)
Tab (one at either \g\fide) Screw for cab\be cover 
(M3 \fcrew)
(with f\bat wa\fher, 
\fpring wa\fher)
Screw for cab\be cover (M3 \fcrew)
(with f\bat wa\fher, \fpring wa\fher)
Square ho\be 
(one at either \fide\g)
Cab\be c\bamp
Strap part
pqHow to \fecure the AC 
adaptor cab\be
1  Loo\fe\by \fecure the cab\be 
c\bamp.
2
 
F
 a\ften the cab\be c\bamp.
Loosely secure the\g cable 
clamp in the area \gshown 
above.
Take hold of the strap part, slide 
the cable clamp until it \gstops 
moving, and then secur\ge it tightly.
7	Attach the cab\be cover. 
						

							18
Stand-a\bone in\fta\b\ba\gtion  
(when the mount bra\gcket i\f not going to \gbe u\fed)
pwWhen in\fta\b\bing the \gunit on a de\fktop
P\bace the unit f\bat \gon the \furface.
p
Install the unit i\gn a stab
 le location which \gwill not be suscep\gtible to shaking. If the unit is in\gstalled in a locati\gon which is 
susceptible to shaking, this\g will cause the un\git’s images to shake in turn.
p
T

ake care not to allo\gw the unit to fall or otherwise b\ge damaged during installation.
p
When carr

ying the unit, do no\gt hold it by its head.
p
Do not tak

e hold of the camer\ga head or rotate it\g. Doing so may cause malfunctio\gning.
p
T

ake care not to pull\g the connected cables. Doing so may cause the unit t\go fall and/or it may result in injury.
Note\f
En\fure that the uni\gt wi\b\b not fa\b\b off.
OK NG
pwWhen mounting the u\gnit on a  tripod
Attach the tripod to the threaded \gholes for mounting the cam\gera on the camera’s bottom panel.
Place the tripod on a completel\gy flat and level surface.
Tighten the screws by hand to mount the\g tripod securely.
Use screw for mounting the tripod that satisfy t\ghe following standard.
Screw for mounting tripod
1/4-20UNC, ISO1222 (6.35
  mm)
4.5
  mm to 6   mm
(0.18 to 0.24
  inche\f)
pDo not install the\g unit where people\g will be passing ba\gc k and forth.
p
When using the unit\g mounted on a tr
 ipod, do not put the\g tripod high above the floor level.
p
\bount the unit secu\grely so there is n\go looseness

. Looseness may cause the unit t\go fall off and/or resu\glt in injuries.
p
When the unit is go\ging to be used f

or a prolonged period of time, take steps to ensure \gthat the unit will\g not topple or fall 
over and that it will\g not fall off or fall down. After using the un\git, restore the in\gstallation locatio\gn to its original state withou\gt 
delay.
Note\f 
						

							19
Installation
	
Instructions
Connection\f
pwConnection\f with an\g  HD monitor
HD monitor HDMI \figna\b (AW
-
 HE60H on\by), SDI \figna\b (AW
-
 HE60S on\by) or 
HD ana\bog component \g\figna\b HD Integrated Camer\ga 
AW
-
 HE60
Wire\be\f\f remote contr\go\b\ber (optiona\b acce\f\g\fory)
Up to four units can be o\gperated using one remot\ge control. 
						

							20
Connection\f(continued)
pwConnection\f with a \g contro\b\ber (AW- RP655 or AW- RP555)
YPBPRVINOUT
LAN cab\be (\ftraight cab\be)
Pan-ti\bt head/ 
camera contro\b \figna\b\f HD Integrated Camer\ga 
AW
-

HE60
Mu\bti Hybrid 
Contro\b Pane\b 
AW
-

RP555 HDMI/SDI video \fign\ga\b
AC Adapter 
AW
-

PS550 Acce\f\fory AC adaptorMonitor
Mu\bti-Function Cont\gro\b\ber 
AW
-

RP655 AC Adapter 
AW
-

PS550Mu\bti-Interface 
Cab\be
AW
-

CA20T6
RJ-45 re\bay 
adapter
pPrecaution\f when u\fi\gng the A
W- RP655 or AW- RP555 contro\b\ber
Before connecting a mo\gdel AW
-
 RP655 or AW–RP555 controller \gthat was manufactured prior to June 2010 to the 
AW
-

HE60H or AW
-
 HE60S camera and using it to co\gntrol the camera, the firmware of the control\gler must be updated.
For details, consult your dealer.
Note
Mu\bti-Interface Cab\g\be AW- CA20T6
Y
PB
PR
V
IN
OUT
pHD/SD component out\gput   1, 
VBS output  1
p
RS-422 interface
p
Use of this cab

le makes it possible for the component a\gnd VBS signals to be o\gutput at the same \gtime as the output\g of the 
HD\bI (AW
-

HE60H) or SDI (AW
-

HE60S) signals.