Panasonic Electronic Print Board KX-BP800 Operating Instructions

21
Paper Jams
Using
Remove paper jams by the following procedure when copy paper does not co\
me out of the output port or when  
flashes on the multi-copy/error indicator.
Printer Door
Printer
Open Lever
1Push down the printer open lever to open the
printer door.
Film
Cassette
2Remove the film cassette with both hands.
Jammed Paper
3Remove all jammed paper.
Slack Prohibited
Label
Thermal 
Transfer Film4If the thermal transfer film is slack, take up the
slack by winding the gears on the label side of
the...

22
Paper Jams
Blue Label
Grooves
Grooves
5Install the film cassette.
CInsert the film cassette into the printer so that
the blue gear on the cassette aligns with the
blue label on the printer and then insert the
gear shafts on both sides of the cassette into
the grooves inside the printer.
Printer Door
6Close the printer door.
CSecurely close the printer door with both hands
until a click is heard.
CThe  flashing on the multi-copy/error
indicator will go out.
C C
If the flashing   does not go out after...

23
Paper Jams
Using
Maximum Paper LimitGuide
3To prevent paper jams such as those caused
by multiple sheets feeding, once fan the paper
thoroughly, square it, align it with the guide
inside, and insert as far as it will go.
C
Do not stack more copy paper in the unit than
the maximum paper limit indicated by the guide
(see figure to the right) as this may result in
paper jams. [Note that the unit can hold about
80 sheets of paper having a weight of 80g/m
2
(21 lbs).]
Note
Paper Cover
4Close the paper cover. 

24
Before Using the Interactive Function
nSetting the Electronic Pen
Marker for Interactive
CapAdaptorColor 
Identification Cap
Remove the 
temporal cap.
3
1
2
2
Inserting
Pen Holder
LeverLocking
Releasing
Marker for 
Interactive
3
1
23
+
-
+ -
3
1
2
Battery
Cover
Pen Holder1Remove the battery cover on the pen holder,
insert the batteries as shown in the figure to
the right, and re-attach the battery cover.
CAlways use “AAA” size (alkaline) batteries and
be sure that their polarity is properly oriented....

Using
25
Before Using the Interactive Function
+
+
--
Eraser
Eraser
Cover
Electronic
3
1
2
4
Remove the eraser cover, insert the batteries as
shown in the figure to the right, and re-attach the
eraser cover.
C
Always use “AAA” size (alkaline) batteries and be
sure that their polarity is properly oriented.
C Do not mix old and new, different type batteries
when replacing batteries.
n Setting the Electronic Eraser
n Replacing the eraser cloth
Press
Hole
Eraser Cloth1Remove the eraser cloth by pushing...

26
Before Using the Interactive Function
nConnecting to the PC nSystem requirements
Interactive Board
Interactive Cable
To the PC
(communication port)Tray
Interactive
Connector
1Connect one end of the proprietary interactive
cable supplied to the interactive connector
under the tray and the other end to the
computers communication (COM) port.
CBe sure to turn off the electronic print board
and PC before you connect or take off the
interactive cable.
2After connecting the interactive cable, securely...

Using
27
Before you start
Before Using the Interactive Function
n Installing the software
In order to use interactive functions by connecting a computer and the
Interactive Panaboard, it is necessary to install the Interactive
Panaboard Software.
When you insert  the CD-ROM into the  CD-ROM drive, the Installation
Software will run *automatically. This will display the software menu on\
the right. This menu consists of two sub menus;
Manuals C
C
Readme - You can view the readme file
C
C
Operating...

28
Before Using the Interactive Function
C CInstalling Adobe®Acrobat®Reader
(1) Click Acrobat (R) Reader in Manuals group of the Automatic Installation Software.
C C
Installation of Adobe®Acrobat®Reader will start.
(2) Follow the instructions on the screen to complete the installation. C C
In order to view the Operating Instruction Manual on the CD ROM, Reference of the
Interactive Panaboard Operating Instructions in CD-ROM
C C
Adobe®Acrobat®Reader is necessary to refer to the Operating Instructions.
If...

Using
29
Using the Interactive Panaboard Software
nStart up the Interactive Panaboard Software
When the Projector mode is selected:
The calibration start screen will be displayed, then calibrate to adjust\
 the position of the projected image and the
position of the Interactive Panaboard screen.
When the calibration is completed and the Projector mode become active, \
the icon  will be registered in the
Taskbar and the Desktop Drawing Tool will appear automatically.
CIn the Projector mode, the Desktop...

30
Using the Interactive Panaboard Software
nPop-up menu configuration of the Interactive Panaboard Software
nSwitching the mode
Right-click the  in the Taskbar to get the pop-up menu.
Following operations are possible in the pop-up menu.
Select Mode... : Allow you to switch between modes (Projector mode/ Whiteboard mode).
Calibrate : Execute the calibration. (Projector mode only)áPage 33
Tool Draw : Display the Desktop Drawing Tool.  (Projector mode only)áPage 36
View Window : Display the View window....