Panasonic Electronic Print Board KX-BP800 Operating Instructions

71
Help
Specifications
Wall-mounting Kit KX-B063
Stand KX-BP065
for PrintBoard
PC Interface Kit KX-BP095 (for connection to PC)
Replacement Film
KX-BP081 [contains two 100m (328.1) rolls]KX-BP082 [contains 100m (328.1) roll and film cassette]
Markers (Big) and Eraser SetKX-B035 (contains one black, one red, one blue marker,  and one eraser)
KX-BP0385 (contains one black, one red, one blue and  one green marker)
Pen HolderKX-BP038
KX-BP048
for Interactive
Electronic Eraser
Marker (Small) set
KX-BP0481...

72
Installation Manual
(for qualified service personnel)
Assembling the Print Board . . . . . . . . . . .
73
CAssembly . . . . . . . . . . . . . . . . . . . . . . .73
Print Board Operations Check  . . . . . . . . .
76
CNormal print board operations check . . . . .76
C Interactive operations check
 . . . . . . . . . . .77
Repacking  . . . . . . . . . . . . . . . . . . . . . . . .
77
Pages
Assembling the Optional Stand (KX-BP065) . . . . .78
CAccessories . . . . . . . . . . . . . . . . . . . . .78
C...

Installation
73
Assembling the Print Board
nAssembly
· Film cassette . . . . . . . . . . . . . . . . . . . . . . . . .  1
· Blue gear . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1
· Green gears . . . . . . . . . . . . . . . . . . . . . . . . . .  3
· Thermal transfer film [20m (65.6)] . . . . . . .  1
· Markers (Black, Red, Blue-Big) . . . . . . .
Each 1
· Eraser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
· Letter papers . . . . . . . . . . . . . . . . . . . 
20 sheets...

74
Assembling the Print Board
3Attach the print board. 
nIf you are using a stand: 
1. Hang the print board on the attachment fixtures of the stand.
2. Use the two wing bolts (M5  12 mm) provided with the stand
to fasten the print board to the
lower stand attachment fixtures
as shown below. n
If you are using a wall-
mounting kit:
1. Remove the two wing bolts and hang the print board on the wall-
mounting fixtures supplied with
the wall-mounting kit.
(Please refer to page 82.)
2. Use the two wing bolts...

Installation
75
Assembling the Print Board
4Attach the power cord. 
1. Securely fit the supplied powercord into the AC inlet on the
printer unit.
2. Fit the power cord into the cord holder. Do not force it.
CDo not use thinner, benzine or cleaners
containing abrasives as this may result in
discoloration.
C Do not wipe the screen film with a dry
cloth as this may generate a static
charge.
5Wipe the screen film surface. 
Wipe the screen film gently with a
water-dampened cloth that has
been thoroughly...

76
Print Board Operations Check
After assembling the print board, perform the procedures presented in th\
e following table to make sure it functions
properly.
nNormal print board operations check
Step
Normal print board operations (points to check)
Multiple copy/error displayOther points to check
1Turn on the power switch.   flashes after
  lights up.
2Open the printer door and attach the supplied
thermal transfer film, then close the printer door.
C
Installing Thermal Transfer Film procedure 
(refer to...

Installation
77
Print Board Operations Check
nInteractive operations check
1Connect the print board to the PC according to the instructions of page \
26 using the
supplied interactive cable.
2Install the software on the PC according to the instructions of page 27 \
and check that
the interactive function operates.
If the Electronic Pen position shifts, adjust the position according to \
the instructions of page 31.
Joint
Shipping Box
Perform assembly steps 2 through 4 (refer to pages 73 through 75) in r\...

78
Assembling the Optional Stand (KX-BP065)
nAccessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present
before beginning installation.
No.Part namePart illustrationQtyNo.Part namePart illustrationQty
Stand base 2
Pipe 2
Cover 2
Side bar A2
Side bar B1
Screw 12
Fixture
(left)2
Fixture
(right)2
Wing bolt 6
Support
bracket2
Fall-prevention
extension leg4
Screw 4
Nut 4
Wrench 1
M8545mm (125/32)M5512mm (
15/32)
M6560mm (2
3/8)
1 The accessory...

Installation
79
Assembling the Optional Stand (KX-BP065)
nAssembly
1Assembling the stand
13
12
1
11
Assembling the fall-prevention extension legs.
The fall-prevention extension legs increases the safety of the
electronic print board.
Fall-prevention extension legs
C Caster locks are attached to
the back side. Insert the covers to the pipes  .
3
2
]
1
]1A
Assemble with the 
holes toward the front.
Locking casters side.
(rear)
Locking 
casters side.
(rear) C
To lock the fall-prevention
   extension legs,...

80
Assembling the Optional Stand (KX-BP065)
2Attach the attachment fixtures  with the four wing-bolts.8
9
9
9
9
8
8
7
7
3Assemble and install the print board.
Please refer to assembly instructions on page 74.