Panasonic Electronic Print Board KX-BP800 Operating Instructions

							71
Help
Specifications
Wall-mounting Kit KX-B063
Stand KX-BP065
for PrintBoard
PC Interface Kit KX-BP095 (for connection to PC)
Replacement Film
KX-BP081 [contains two 100m (328.1) rolls]KX-BP082 [contains 100m (328.1) roll and film cassette]
Markers (Big) and Eraser SetKX-B035 (contains one black, one red, one blue marker,  and one eraser)
KX-BP0385 (contains one black, one red, one blue and  one green marker)
Pen HolderKX-BP038
KX-BP048
for Interactive
Electronic Eraser
Marker (Small) set
KX-BP0481 (set of 10 cloths)Eraser Cloth (for Electronic Eraser)
n Consumable and accessories
Ruler kit (KX-B05) can not be used with the interactive function.
C The markers (Big) and the eraser are used for other than the interacti\
ve function.
C The markers for interactive (Small) are used while inserted in the pen\
 holder.
The Electronic Pen [a marker for interactive (Small) inserted in the p\
en holder] and the Electronic Eraser are used
with the interactive function.\
C PC Interface (Option)
When the optional PC Interface Kit (KX-BP095) is used, you can scan mo\
nochrome images from the KX-BP800 into
a computer running Microsoft
®Windows®or Windows NT®and print documents on the computer to the printer of the
KX-BP800. 
						

							72
Installation Manual
(for qualified service personnel)
Assembling the Print Board . . . . . . . . . . .
73
CAssembly . . . . . . . . . . . . . . . . . . . . . . .73
Print Board Operations Check  . . . . . . . . .
76
CNormal print board operations check . . . . .76
C Interactive operations check
 . . . . . . . . . . .77
Repacking  . . . . . . . . . . . . . . . . . . . . . . . .
77
Pages
Assembling the Optional Stand (KX-BP065) . . . . .78
CAccessories . . . . . . . . . . . . . . . . . . . . .78
C Assembly
 . . . . . . . . . . . . . . . . . . . . . . .79
Wall-mounting Kit (KX-B063)  . . . . . . . . . .
81
CAccessories . . . . . . . . . . . . . . . . . . . . .81
C Wall-mounting procedure
 . . . . . . . . . . . . .82
C Attaching the wall-mounting fixtures
 . . . . . .83
Pages
T
able of contents
Before installing this set, please read this manual completely.
For instructions on installing the software, please see page 27.
WARNING
DO NOT INSTALL THIS OPTION EXCEPT QUALIFIED SERVICE PERSONNEL.
CAUTION
SAFETY CHECK MUST BE DONE BY QUALIFIED SERVICE PERSONNEL
AFTER INSTALLING THIS OPTION.
Accessories
The following accessories are required for assembly.
Part namePart illustration/quantityAttachment procedure
Power cord Page 75, Item 4.1
Wall mounting template
(for wall mounting)
Page 82, Item 25 1
5
1
All accessories included in the package are given on the next page. 
Make sure that all of these parts are included in the package before pro\
ceeding. 
						

							Installation
73
Assembling the Print Board
nAssembly
· Film cassette . . . . . . . . . . . . . . . . . . . . . . . . .  1
· Blue gear . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1
· Green gears . . . . . . . . . . . . . . . . . . . . . . . . . .  3
· Thermal transfer film [20m (65.6)] . . . . . . .  1
· Markers (Black, Red, Blue-Big) . . . . . . .
Each 1
· Eraser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
· Letter papers . . . . . . . . . . . . . . . . . . . 
20 sheets
· Pen holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
· Markers  for interactive 
(Black, Red, Blue, Green-Small)  . . . . . .
Each 1
· Electronic eraser  . . . . . . . . . . . . . . . . . . . . . . .
1
· Eraser cloth (for electronic eraser)  . . . . . . . . .
2
· Batteries (LR03 AAA)  . . . . . . . . . . . . . . . . . .
6
· Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
· Interactive cable (5m) . . . . . . . . . . . . . . . . . . .
1
· Software CD-ROM . . . . . . . . . . . . . . . . . . . . . .
1
· Operating Instructions . . . . . . . . . . . . . . . . . . .
1
· Software License Agreement  . . . . . . . . . . . . . .
1
· Wall-mounting template . . . . . . . . . . . . . . . . . .
1
· Warranty card . . . . . . . . . . . . . . . . . . . . . . . . .
1
1Assembly of the optional stand or wall-mounting kit. 
nIf you are using a stand, refer to page 78.
n If you are using a wall-mounting kit, refer to page 81.
2Remove the print board from the shipping box. 
Remove the joints, then remove the print board from the shipping box.
CDo not touch the screen film surface as doing so may damage it.
C The shipping box, cushioning material, and other packaging materials wil\
l be necessary if
you ever need to repackage the print board, so do not throw them away.
Note 
						

							74
Assembling the Print Board
3Attach the print board. 
nIf you are using a stand: 
1. Hang the print board on the attachment fixtures of the stand.
2. Use the two wing bolts (M5  12 mm) provided with the stand
to fasten the print board to the
lower stand attachment fixtures
as shown below. n
If you are using a wall-
mounting kit:
1. Remove the two wing bolts and hang the print board on the wall-
mounting fixtures supplied with
the wall-mounting kit.
(Please refer to page 82.)
2. Use the two wing bolts removed in step 1 above to fasten the print
board to the lower wall-mounting
fixtures as shown below.
CWhen mounting the print board, avoid banging it.
Such impact may break the internal fluorescent
light or cause other damage.
C After mounting the print board, gradually apply
weight to it to make sure that the wall is strong
enough to support it.
L
R
L
R
1
2
C The stand (KX-BP065) is available as an option. CThe wall-mounting kit (KX-B063) is available as an
option.
Note 
						

							Installation
75
Assembling the Print Board
4Attach the power cord. 
1. Securely fit the supplied powercord into the AC inlet on the
printer unit.
2. Fit the power cord into the cord holder. Do not force it.
CDo not use thinner, benzine or cleaners
containing abrasives as this may result in
discoloration.
C Do not wipe the screen film with a dry
cloth as this may generate a static
charge.
5Wipe the screen film surface. 
Wipe the screen film gently with a
water-dampened cloth that has
been thoroughly wrung.
6Check operations.  
Refer to page 76 Print Board
Operations Check.
Power Cord
AC Inlet
Cord Holder
Note 
						

							76
Print Board Operations Check
After assembling the print board, perform the procedures presented in th\
e following table to make sure it functions
properly.
nNormal print board operations check
Step
Normal print board operations (points to check)
Multiple copy/error displayOther points to check
1Turn on the power switch.   flashes after
  lights up.
2Open the printer door and attach the supplied
thermal transfer film, then close the printer door.
C
Installing Thermal Transfer Film procedure 
(refer to page 14)  flashes.
3Open the paper cover and insert ordinary Letter
test paper, then close the paper cover.
CLoading Copy Paper procedure 
(refer to page 16)  lights up.
4Open the printer door.   flashes.
5Close the printer door.  lights up.
6Press .C
Does the screen film surface
feed smoothly
?
C Are there any strange noises?
7Use the supplied marker to draw a large 
filling the entire copyable area of the 
screen film surface.
C Copyable area (refer to page 9)
Press  twice. (will add to 3 copies)
Cwill be displayed.
Press .
  lights up.
CAre three copies made?
C Is the entire readable area
printed?
C During the copying process, are
there any strange noises or
paper jams? Are multiple sheets
of paper fed through at the same
time?
8Press  to move the screen film surface. 
Write letters, etc. with the marker.
Press once.
Press  
.
C Has the darkness indicator light
turned on?
C Is the image copied properly?
C Are there strange markings on
the copy sheet (e.g., stripes or
lines)?
9Press once.Has the darkness indicator light
turned off?
10Press .1 2Are two screens copied properly?
B If the unit fails on any of the check points, please contact your dealer\
. 
						

							Installation
77
Print Board Operations Check
nInteractive operations check
1Connect the print board to the PC according to the instructions of page \
26 using the
supplied interactive cable.
2Install the software on the PC according to the instructions of page 27 \
and check that
the interactive function operates.
If the Electronic Pen position shifts, adjust the position according to \
the instructions of page 31.
Joint
Shipping Box
Perform assembly steps 2 through 4 (refer to pages 73 through 75) in r\
everse to repack
the print board and accessories. Use the joints to fasten the shipping b\
ox to the upper and
lower box.
C Refer to the shipping box instructions
for information on how to fasten the
16 joints.
Repacking 
						

							78
Assembling the Optional Stand (KX-BP065)
nAccessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present
before beginning installation.
No.Part namePart illustrationQtyNo.Part namePart illustrationQty
Stand base 2
Pipe 2
Cover 2
Side bar A2
Side bar B1
Screw 12
Fixture
(left)2
Fixture
(right)2
Wing bolt 6
Support
bracket2
Fall-prevention
extension leg4
Screw 4
Nut 4
Wrench 1
M8545mm (125/32)M5512mm (
15/32)
M6560mm (2
3/8)
1 The accessory wrench is required when disassembling the electronic print board; please store
it carefully for future use.
CBefore assembly, be sure to lock the casters.
Locking the casters
(Push this side)
Releasing the lock
8
9
10
11
12
13
1 
						

							Installation
79
Assembling the Optional Stand (KX-BP065)
nAssembly
1Assembling the stand
13
12
1
11
Assembling the fall-prevention extension legs.
The fall-prevention extension legs increases the safety of the
electronic print board.
Fall-prevention extension legs
C Caster locks are attached to
the back side. Insert the covers to the pipes  .
3
2
]
1
]1A
Assemble with the 
holes toward the front.
Locking casters side.
(rear)
Locking 
casters side.
(rear) C
To lock the fall-prevention
   extension legs, lift portion A.
6
33
5
2
2
6
6
4
4
10
10
1 Do not tighten the screw  too much. This may deform the pipes. 
						

							80
Assembling the Optional Stand (KX-BP065)
2Attach the attachment fixtures  with the four wing-bolts.8
9
9
9
9
8
8
7
7
3Assemble and install the print board.
Please refer to assembly instructions on page 74.