Panasonic Electronic Print Board KX-BP800 Operating Instructions

							Installation
81
——
Wall-mounting Kit (KX-B063)
Before attempting installation of this wall-mounting kit, we strongly re\
commend consulting with the building facility nor
manager, engineer, or architect. The installer needs to know the type of\
 construction used for the wall intended for this
installation and the location of wall studs. Selection of hardware is cr\
itical for safe wall-mounting, and dependent upon
the nature of wall construction, installation should not occur until thi\
s consultation takes place.
Procedure for KX-B063 Wall-mounting Kit Installation
.Tools required:
One (1) KX-B063 kit
A minimum of eight (8) pieces of appropriate wall-support hardware (m\
olley, toggle, etc.) 
NOTE :THIS HARDWARE MUST BE LOCALLY PROCURED, IT IS NOT INCLUDED IN THE \
KIT.
Drill (and drill bit of correct size) for hardware installation
Screw driver (Both phillips (+) and slotted (-) will be required.)\
 
Tape measure
Tape or thumb-tacks (2pcs) 
Bubble type level
.Pre-requisites1. Before installation, make sure that the wall intended for installation i\
s capable of supporting flush-mounted. 
[ KX-BP800 is 103 kgf (227 Ibs). ]
2. The position of the intended installation is of adequate size for the se\
lected Panaboard. [ KX-BP800 is 1,575 mm X 1,524 mm (52 55).]
3. An outlet is within 3 m (910
4/32), and it is not located directly behind the Panaboard.
n Accessories
The package includes the parts noted below ; please confirm that all par\
ts are present before beginning installation.
Eight screws for mounting the fixtures on the wall are not provided. Ple\
ase purchase the appropriate wall-mounting
hardware (sold in stores). Refer to pages 83 and 84.
No.Part namePart illustration, Qty
L
Order 
of useNo.Part namePart illustration, QtyOrder 
of use
Wall-mounting
fixture L 3
2
Wall-mountingtemplate
RWall-mounting fixture R 3
Wing bolt
5
2
5 2
5 2
M5 512 mm (
15/32)
No use* No use*
Use the wall-mounting
template provided with
KX-BP800.
These are used for other models.
5
1
Screw
54
M4 516 mm
No use* 
						

							82
Wall-mounting Kit (KX-B063)
nWall-mounting procedure
1Confirm that the wall is strong enough to support the weight of the prin\
t board.
(Please refer to page 81.)
2Tape the wall-mounting template to the wall.
B Do not use the template included in the wall-mounting kit (KX-B063), b\
ut rather the one included
with the electronic print board (KX-BP800).
B When taping the template to the wall, make sure it is level. Caution:
The wall must be capable of supporting at least
1,005N [ 103 kgf (227 Ibs) ] for KX-BP800.
31. Drill holes in the wall for the wall-mounting fixtures. (8 holes tot\
al)
2. After removing the wall-mounting template, attach the wall-mounting f\
ixtures withthe appropriate wall-mounting hardware (two screws in each fixture).
This hardware must be locally procured, it is not included in the kit.
B Refer to the section Attaching the wall-mounting fixtures (pages 83 a\
nd 84) for drilling in the wall and
attaching the mounting fixtures.
Mount the print board. (Please refer to page 74.)
1
5
Wall-mounting
fixture L Wall-mounting
template (provided with KX-BP800)
Wall-
mounting
hard ware*
W all-mounting
fixture L
W all-mounting
fixture R
W all-
mounting
hard ware*
812.8mm (2 8)
70 mm
  (2     )   3 4
50mm
  (2) 762mm (26)
2
1
L
L
R
R 
						

							Installation
83
Wall-mounting Kit (KX-B063)
nAttaching the wall-mounting fixtures
The electronic print board must be mounted with the method most suited t\
o the material of the wall.
Three methods are presented here.
(Other options may be available in your area.)
B Attaching to metal or concrete walls
Stud plugs (sold in stores) are needed.
Drill bit
Metal or concrete
wall
Stud plug
Insert a stud plug in each hole.
Wall-mounting
fixture
Bolt
Drill eight holes in the wall.
For the correct hole size,
refer to the instructions for
the particular stud plugs
used.
Insert each bolt through a
hole in the wall-mounting
fixture and tighten until the
wall-mounting fixture is
securely fixed to the wall. 
						

							84
Wall-mounting Kit (KX-B063)
BAttaching to plasterboard walls
Split-wing toggles (sold in stores) are needed.
Wall-mounting
fixture
Bolt
Plasterboard
split-wing toggle
Arms
Arms
Insert each bolt through a
hole in the wall-mounting
fixture and into the hole in
the wall beneath so that the
arms of the split-wing
toggle are horizontal. 
For the correct hole size,
refer to the instructions for
the particular split-wing
toggles used.
Tighten each bolt until the
wall-mounting fixture is
securely fixed to the wall.
For the correct hole size,
refer to the instructions for
the particular wood screws
used. After the arms expand, pull
the wall-mounting fixture
out until the arms of the
split-wing toggle grip firmly
into the wall.
BAttaching to wooden walls
Use wood screws (sold in stores).
Wall-mounting fixture
Wood screw
Wooden wall 
						

							85
MEMO 
						

							These Operating Instructions are printed on recycled paper.
Panasonic Digital Imaging Solutions Company
Business Unit of Matsushita Electric Corporation of America
Two Panasonic Way, Secaucus, New Jersey 07094
Printed in MalaysiaPBQX50256ZB   K0601E0
©2001 Kyushu Matsushita Electric Co., Ltd. All Rights Reserved.